aion Apollo Mk I Manual 

1 PROJECT NAME APOLLO MK. I BASED ON EFFECT TYPE PROJECT SUMMARY DOCUMENT VERSION Catalinbread® WIIO An adaptation of the Hiwatt amplifier used by Pete Townshend of The Who during their “Live at Leeds” performance from 1970. Overdrive / Amp Emulation 1.0.0 (2021-02-19) Actual size is 2.3” x 1.86” (main board) and 1.78” x 0.87” (bypass board). BUILD DIFFICULTY Intermediate This documentation is for the Mk. I version of the project. There is also a Mk. II version, based on the RAH. While the names are similar, the circuit and part numbering are different. Please be sure your PCB is labeled “Apollo Mk. I” before proceeding with this build document. IMPORTANT NOTE

2 TABLE OF CONTENTS 1 Project Overview 7 Drill Template 2 Introduction & Usage 8 Enclosure Layout 3-4 Parts List 9 Wiring Diagram 5 Build Notes 10 Licensing 6 Schematic 10 Document Revisions INTRODUCTION The Apollo Preamp Drive Mk. I is an adaptation of the Catalinbread WIIO, based on the Hiwatt amplifiers used by Pete Townshend of The Who, particularly their Live at Leeds show from February 14, 1970. (The artwork for the original pedal makes it obvious that “WIIO” is intended to resemble “WHO”.) The WIIO was originally released in 2009 as a limited run of 100. The limited availability caused a huge debacle as people from gear forums bought up all the preorders and flipped them for profit, capitalizing on Catalinbread’s favored status among gear aficionados. Catalinbread was not happy with the way the circuit turned out, so before releasing the non-limited version, they overhauled the circuit to reduce the gain and tweak the EQ so it was more versatile as an amp platform. Most people agree that the second version is superior, but the hype surrounding the first version has given it a lasting reputation. The WIIO was succeeded by the RAH, which is largely the same circuit but with a midrange knob added, and the circuit re-voiced for Led Zeppelin’s famous show at the Royal Albert Hall. (They even referred to the RAH as the “Royal Albert Hall Edition of the WIIO” in the manual.) The WIIO was discontinued shortly after the release of the RAH. The Apollo Mk. I is a direct adaptation of the V2 WIIO (non-limited version). The only modification is the addition of a trimmer that makes a feedback resistor variable, allowing adjustments to the gain, tone and feel of the circuit. The RAH is also available from Aion FX as the Apollo Mk. II. USAGE The Apollo Mk. I has the following controls: • Gain controls the amount of gain coming out of the first amplifier stage. • Bass and Treble form a 2-band tone stack adapted from the original amplifier. • Master is the overall output level. • Feedback (internal trimmer) controls the global feedback from the third stage back to the first. Set it just past the halfway point for the stock circuit, and then adjust it to taste.

3 PARTS LIST This parts list is also available in a spreadsheet format which can be imported directly into Mouser for easy parts ordering. Mouser doesn’t carry all the parts (most notably potentiometers) so the second tab lists all the non-Mouser parts as well as sources for each. View parts list spreadsheet → PART VALUE TYPE NOTES R1 10M Metal film resistor, 1/4W R2 3k3 Metal film resistor, 1/4W R3 3k3 Metal film resistor, 1/4W R4 1k Metal film resistor, 1/4W R5 12k Metal film resistor, 1/4W R6 10M Metal film resistor, 1/4W R7 3k3 Metal film resistor, 1/4W R8 3k3 Metal film resistor, 1/4W R9 100k Metal film resistor, 1/4W R10 10k Metal film resistor, 1/4W R11 10M Metal film resistor, 1/4W R12 3k3 Metal film resistor, 1/4W R13 3k3 Metal film resistor, 1/4W R14 130R Metal film resistor, 1/4W R15 47k Metal film resistor, 1/4W R16 12k Metal film resistor, 1/4W R17 12k Metal film resistor, 1/4W R18 62k Metal film resistor, 1/4W R19 82k Metal film resistor, 1/4W R20 100R Metal film resistor, 1/4W RPD 2M2 Metal film resistor, 1/4W LEDR 4k7 Metal film resistor, 1/4W C1 270pF MLCC capacitor, NP0/C0G C2 100n Film capacitor, 7.2 x 2.5mm C3 100uF Electrolytic capacitor, 6.3mm C4 100n Film capacitor, 7.2 x 2.5mm C5 47n Film capacitor, 7.2 x 2.5mm C6 100uF Electrolytic capacitor, 6.3mm C7 4.7uF Electrolytic capacitor, 4mm C8 4n7 Film capacitor, 7.2 x 2.5mm

4 PARTS LIST, CONT. PART VALUE TYPE NOTES C9 10n Film capacitor, 7.2 x 2.5mm C10 10n Film capacitor, 7.2 x 2.5mm C11 470pF MLCC capacitor, NP0/C0G C12 100n Film capacitor, 7.2 x 2.5mm C13 100uF Electrolytic capacitor, 6.3mm C14 470n Film capacitor, 7.2 x 3mm C15 10uF Electrolytic capacitor, 5mm C16 2n2 Film capacitor, 7.2 x 2.5mm C17 2n2 Film capacitor, 7.2 x 2.5mm C18 47uF Electrolytic capacitor, 5mm C19 100uF Electrolytic capacitor, 6.3mm C20 100n MLCC capacitor, X7R D1 1N5817 Schottky diode, DO-41 Z1 1N4739A Zener diode, 9V, DO-41 Z2 1N4739A Zener diode, 9V, DO-41 Z3 1N4739A Zener diode, 9V, DO-41 Q1 BS170 MOSFET, N-channel, TO-92 Q2 BS170 MOSFET, N-channel, TO-92 Q3 BS170 MOSFET, N-channel, TO-92 GAIN 500kA 16mm right-angle PCB mount pot BASS 500kA 16mm right-angle PCB mount pot TREBLE 500kB 16mm right-angle PCB mount pot MSTR. 100kA 16mm right-angle PCB mount pot FDBK. 250k trimmer Trimmer, 10%, 1/4" See build notes. IN 1/4" stereo 1/4" phone jack, closed frame Switchcraft 112BX or equivalent. OUT 1/4" mono 1/4" phone jack, closed frame Switchcraft 111X or equivalent. DC 2.1mm DC jack, 2.1mm panel mount Mouser 163-4302-E or equivalent. FSW 3PDT Stomp switch, 3PDT ENC 125B Enclosure, die-cast aluminum Can also use a Hammond 1590N1.

5 BUILD NOTES Setting feedback trimmer The WIIO circuit contains a global feedback loop similar to the amplifier it’s based on. A 200k resistor and 470n capacitor send the output from the third stage back to the point just after the gain control between the first and second stage, which reduces the gain, cuts some of the top end, and makes it feel more “amp-like”. The Apollo Mk. I adds a trimmer in series with the feedback resistor, allowing the feedback to be varied to taste. Global feedback does several things at once with the gain, EQ and compression The stock position is between 1-2:00 on the trimmer and this should be the starting point for any builds. From there, adjust it up or down and see if you like what it does. If you want to omit this control, jumper the outer pins of the trimmer and use 200k for R15.

6 GND 2M2 1N5817 100uF 500kA 500kA GND 500kB 100kA +9V 100n VA 270pF 100n GND 10M 100R 62k 82k 47uF GND GND VB VB 1N4739A BS170 3k3 VA 3k3 1k GND GND 100uF 100n 12k GND 47n 10M 1N4739A BS170 3k3 100uF GND GND 3k3 VB VA 4u7 100k 4n7 10n GND GND 10k 10n GND 470pF 100n 10M VB 1N4739A BS170 3k3 VA 3k3 130R GND GND 100uF 10uF 12k 2n2 2n2 12k 47k 470n 250k GND GND GND IN OUT RPD D1 C19 GAIN 1 2 3 BASS 1 2 3 TREBLE 1 2 3 MASTER 1 2 3 C20 C1 C2 R1 R20 R18 R19 C18 Z1 Q1 R2 R3 R4 C3 C4 R5 C5 R6 Z2 Q2 R7 C6 R8 C7 R9 C8 C9 R10 C10 C11 C12 R11 Z3 Q3 R12 R13 R14 C13 C15 R16 C16 C17 R17 R15 C14 FEEDBACK 1 2 3 GND

7 DRILL TEMPLATE Cut out this drill template, fold the edges and tape it to the enclosure. Before drilling, it’s recommended to first use a center punch for each of the holes to help guide the drill bit. Ensure that this template is printed at 100% or “Actual Size”. You can double-check this by measuring the scale on the printed page. Top jack layout assumes the use of closed-frame jacks like the Switchcraft 111X. If you’d rather use open-frame jacks, please refer to the Open-Frame Jack Drill Template for the top side. LED hole drill size assumes the use of a 5mm LED bezel, available from several parts suppliers. Adjust size accordingly if using something different, such as a 3mm bezel, a plastic bezel, or just a plain LED. 0 1 2 CM 0 1 INCH x: -0.65, y: +1.71 x: 0.65, y: +1.71 ø9/32” ø9/32” x: -0.65, y: +0.41 ø9/32” x: 0.65, y: +0.41 ø9/32” x: 0, y: -1.20 ø15/32” x: -0.775, y: -1.20 ø5/16” CENTER (0,0) 125B ø3/8” ø1/2” 0.385” 0.625” 0.625” ø3/8” OUT DC IN MASTER GAIN BASS TREBLE FOOTSWITCH LED

8 ENCLOSURE LAYOUT Enclosure is shown without jacks. See next page for jack layout and wiring. 125B

9 WIRING DIAGRAM 125B IN +V GND N.C. N.C. OUT PCB IN GND +V +V JACK GND JACK OUT IN GND GND PCB OUT

10 LICENSE & USAGE No direct support is offered for these projects beyond the provided documentation. It’s assumed that you have at least some experience building pedals before starting one of these. Replacements and refunds cannot be offered unless it can be shown that the circuit or documentation are in error. All of these circuits have been tested in good faith in their base configurations. However, not all the modifications or variations have necessarily been tested. These are offered only as suggestions based on the experience and opinions of others. Projects may be used for commercial endeavors in any quantity unless specifically noted. No attribution is necessary, though a link back is always greatly appreciated. The only usage restrictions are that (1) you cannot resell the PCB as part of a kit without prior arrangement, and (2) you cannot “goop” the circuit, scratch off the screenprint, or otherwise obfuscate the circuit to disguise its source. (In other words: you don’t have to go out of your way to advertise the fact that you use these PCBs, but please don’t go out of your way to hide it. The guitar effects industry needs more transparency, not less!) DOCUMENT REVISIONS 1.0.0 (2021-02-19) Initial release.