DeWalt DCD735 Original Instructions Manual

DCD730, DCD780 Cordless Compact 13 mm (1/2") Drill/Driver/ Hammerdrill DCD735, DCD785 Congratulations! You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the most reliable partners for professional power tool users.TD  Battery pack DCB140 DCB141 DCB180 DCB181 DCB182 DCB183 DCB184 Battery type Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion Voltage VDC 14.4 14.4 18 18 18 18 18 Capacity Ah 3.0 1.5 3.0 1.5 4.0 2.0 5.0 Weight kg 0.53 0.30 0.64 0.35 0.61 0.40 0.62 Technical Data DCD730 DCD735 DCD780 DCD785 Voltage VDC 14.4 14.4 18 18 Battery Type Li-Ion Li-Ion Li-Ion Li-Ion Power output W 300 300 350 350 Max. torque Nm 57 57 60 60 Chuck capacity mm 13 13 13 13 35 35 38 38 13 13 13 13 Weight (without battery pack) kg 1.2 1.24 1.2 1.24 Charger DCB105 Mains voltage 220~240 V Battery type Li-Ion Approx. charging time min Weight kg 0.49 No-load speed 1st gear 2nd gear min-1 min-1 0–550 0–1900 0–550 0–1900 0–600 0–2000 0–600 0–2000 Impact rate 1st gear 2nd gear min-1 min-1 – – 0–9350 0–32300 – – 0–10200 0–34000 mm mm mm 13 – 13 – VAC 30 (1.5Ah battery p acks) 55 (3.0Ah battery packs) 70 (4.0Ah battery packs) Maximum drilling capacity Wood Metal Masonry

min Weight kg 0.5 (1.3Ah battery p acks) (3.0Ah battery p acks) (4.0Ah battery packs) (5.0Ah battery packs) Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.  NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage. Denotes risk of electric shock. Denotes risk of fire.  WARNING: To reduce the risk of injury, read the instruction manual. General Power Tool Safety Warnings  WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 22 45 60 75 22 (1.5Ah battery packs) 30 (2.0Ah battery packs) e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc., in accordance with these instructions taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. c) When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. d) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 6) serviCe a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Drill/Driver/Hammerdrill • Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. • Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. • Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Wear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly. Flying particles can cause permanent eye damage. • Accessories and tool may get hot during operation. Wear gloves when handling them if performing heat producing applications such as hammerdrilling and drilling metals. • Do not operate this tool for long periods of time. Vibration caused by hammer action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods. • Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in moving parts. Residual Risks The following risks are inherent to the use of drills: – Injuries caused by touching the rotating parts or hot parts of the tool. In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are: – Impairment of hearing. – Risk of squeezing fingers when changing accessories. – Health hazards caused by breathing dust developed when working in wood. – Risk of personal injury due to flying particles. – Risk of personal injury due to prolonged use. Markings on Tool The following pictograms are shown on the tool: Read instruction manual before use. Date Code Position The Date Code, which also includes the year of manufacture, is printed into the housing surface that forms the mounting joint between tool and battery. Example: 2019 XX XX Year of Manufacture Important Safety Instructions for All Battery Chargers­ SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instruc tions for the DCB105 and DCB115 battery charger. • Before using the charger, read all instructions and cautionary markings on charger, battery pack and product using the battery pack. WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result. Caution: Burn hazard. To reduce the risk of injury, charge only DeWALT rechargeable battery packs. Other types of batteries may overheat and burst resulting in personal injury and property damage. CAUTION: Children should be supervised to ensure that they do not play with the appliance. NOTICE: Under certain conditions, with the charger plugged in to the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. • DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together.

any uses other than charging DeWALT rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution. • Do not expose charger to rain or snow. • Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric plug and cord. • Make sure that cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage or stress. • Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock or electrocution. • When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. • Do not block the ventilation slots on the charger. The ventilation slots are located on the top and sides of the charger. Place the charger in a position away from any heat source. • Do not operate charger with damaged cord or plug — have them replaced immediately. • Do not operate charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to an authorised service centre. • Do not disassemble the charger; take it to an authorised service centre when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire. • In case of damaged power supply cord the supply cord must be replaced immediately by the manufacturer, its service agent or similar qualified person to prevent any hazard. • Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk. • NEVER attempt to connect 2 chargers together. • The charger is designed to operate on standard 220~240 V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger. SAVE THESE INSTRUCTIONS Chargers Charging The DCB105 and DCB115 charger accepts 10.8V, 14.4V and 18V Li-Ion (DCB121, DCB140, DCB141, DCB180, DCB181, DCB182 , DCB1 83 and DCB184) battery packs. This charger requires no adjustment and is designed to be as easy as possible to operate. Procedure (figure 2) 1. Plug the charger into an appropriate 220~240 V outlet before inserting the battery pack. 2. Insert the battery pack (j) into the charger, making sure the pack is fully seated in the charger. The red (charging) light will blink continuously indicating that the charging process has started. 3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger. Note: To ensure maximum performance and life of Li-Ion batteries, charge the battery pack fully before first use. Charging Process Refer to the table below for the state of charge of the battery pack. Charge indicators: DCB105 charging –– –– –– –– fully charged ––––––––––––––––– hot/cold pack delay –– • –– • –– • –– • x problem pack or charger • • • • • • • • • • • • problem powerline •• •• •• •• •• •• Charge indicators: DCB115 charging fully charged hot/cold pack delay* This charger will not charge a faulty battery pack. The charger will indicate faulty battery by refusing to light or by displaying problem pack or charger blink pattern. NotE: This could also mean a problem with a charger.

and battery pack to be tested at an authorised service centre. Hot/Cold Pack Delay When the charger detects a battery that is too hot or too cold, it automatically starts a hot/cold pack delay, suspending charging until the battery has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery life. XR Li-Ion tools are designed with an Electronic Protection System that will protect the battery against overloading, overheating or deep discharge. The tool will automatically turn off if the Electronic Protection System engages. If this occurs, place the Li-Ion battery on the charger until it is fully charged. A cold battery pack will charge at about half the rate of a warm battery pack. The battery pack will charge at that slower rate throughout the entire charging cycle and will not return to maximum charge rate even if the battery warms. Important Safety Instructions for All Battery Packs When ordering replacement battery packs, be sure to include the catalog number and voltage. The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below and then follow the charging procedures outlined. Read all Instructions • Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery pack from the charger may ignite the dust or fumes. • Never force the battery pack into charger. Do not modify the battery pack in any way to fit into a non-compatible charger as battery pack may rupture causing serious personal injury. • Charge the battery packs only in designated DeWALT chargers. • DO NOT splash or immerse in water or other • For best results, make sure the battery pack is fully charged before use. WARNING: Never attempt to open the battery pack for any reason. If the battery pack case is cracked or damaged, do not insert it into the charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to the service centre for recycling. Caution: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over. Specific Safety instructions for Lithium Ion (Li-Ion) • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium ion battery packs are burned. • If battery contents come into contact with the skin, immediately wash the area with mild soap and water. If the battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. • Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention. WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame. liquids. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40˚ C (105° F) (such as outside sheds or metal buildings in summer). Battery pack BATTERY TYPE The DCD730 and DCD735 operate on 14.4 volt battery packs. The DCD780 and DCD785 operate on 18 volt battery pack.

DCB183 or DCB184 battery packs may be used. Refer to Technical Data for more information. Storage Recommendations 1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use. 2. For long storage, it is recommended to store a fully charged battery pack in a cool, dry place out of the charger for optimal results. Note: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use. Labels on Charger and Battery Pack In addition to the pictographs used in this manual, the labels on the charger and the battery pack show the following pictographs: Read instruction manual before use. Charging. Fully charged. Hot/cold pack delay. x Problem pack or charger. Problem powerline. Do not probe with conductive objects. Do not charge damaged battery packs. Use only with DeWALT battery packs. Others may burst, causing personal injury and damage. Do not expose to water. Have defective cords replaced immediately. Charge only between 4° C and 40° C. Discard the battery pack with due care for the environment. Do not incinerate the battery pack. Charges Li-Ion battery packs. See technical data for charging time. Only for indoor use. Package Contents The package contains: 1 Drill/driver or 1 drill/driver/hammerdrill 1 Charger 2 Batteries 1 Kitbox 1 Instruction manual Note: Battery packs, chargers and kitboxes are not included with N-models. • Check for damage to the tool, parts or accessories which may have occurred during transport. • Take the time to thoroughly read and understand this manual prior to operation. Description (figure 1) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. a. Trigger switch b. Forward/reverse control button c. Torque adjustment collar d. Gear shifter e. Worklight f. Keyless chuck g. Belt hook h. Mounting screw i. Bit clip j. Battery pack k. Battery release button

for professional drilling, percussion drilling and screwdriving applications. Do not use under wet conditions or in presence of flammable liquids or gases. These drills/drivers/hammerdrills are professional power tools. Do not let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. • This product is not intended for use by persons (including children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with this product. Electrical Safety The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains.  Your DeWALT charger is double insulated in accordance with IEC 60335; therefore no earth wire is required. If the supply cord is damaged, it must be replaced by a specially prepared cord available through the DeWALT service organisation. Using an Extension Cable An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger (see Technical Data). The minimum conductor size is 1 mm2; the maximum length is 30 m. When using a cable reel, always unwind the cable completely. Assembly and adjustments Warning: Prior to assembly and adjustment, always remove the battery pack. Always switch off the tool before inserting or removing the battery pack. Warning: Use only DeWALT battery packs and chargers. Inserting and Removing the Battery Pack from the Tool (figure 2) NOTE: For best results, make sure your battery pack is fully charged. To install the battery pack into the tool handlE 1. Align the battery pack (j) with the rails inside the tool’s handle (figure 2). 2. Slide it into the handle until the battery pack is firmly seated in the tool and ensure that it does not disengage. To remove the battery pack from the tool 1. Press the battery release button (k) and firmly pull the battery pack out of the tool handle. 2. Insert battery pack into the charger as described in the charger section of this manual. Variable Speed Trigger Switch (figure 1) To turn the tool on, squeeze the trigger switch (a). To turn the tool off, release the trigger switch. Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fully released. NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided. Forward/Reverse Control Button (figure 1) A forward/reverse control button (b) determines the direction of the tool and also serves as a lock-off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool. To select reverse, depress the forward/reverse control button on the left side of the tool. The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released. NotE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem.

Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of fastener shapes and sizes and in some models, a hammer mechanism for drilling into masonry. Circling the collar (c) are numbers, a drill bit symbol, and in some models, a hammer symbol. These numbers are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener which can be driven. To select any of the numbers, rotate until the desired number aligns with the arrow. Dual Range Gearing (figure 1) The dual range feature of your drill/driver allows you to shift gears for greater versatility. 1. To select speed 1 (high torque setting), turn the tool off and permit it to stop. Slide the gear shifter (d) forward (towards the chuck). 2. To select speed 2 (low torque setting), turn the tool off and permit it to stop. Slide the gear shifter back (away from the chuck). NOTE: Do not change gears when the tool is running. Always allow the drill to come to a complete stop before changing gears. If you are having trouble changing gears, make sure that the dual range gear shifter is either completely pushed forward or completely pushed back. Worklight (figure 1) There is a worklight (e) located just above the trigger switch (a). The worklight is activated when the trigger switch is depressed. When the trigger is released the worklight will stay illuminated for up to 20 seconds. NOTE: The worklight is for lighting the immediate work surface and is not intended to be used as a flashlight. Keyless Single Sleeve Chuck (figure 7–9) WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may result. Always lock off trigger switch and disconnect tool from power source when changing acces­sories. Warning: Always ensure the bit is secure before starting the tool. A loose bit may eject from tool causing possible personal injury. Your tool features a keyless chuck (f) with one rotating sleeve for one-handed operation of the chuck. To insert a drill bit or other accessory, follow these steps. 1. Turn tool off and disconnect tool from power source. 2. Grasp the black sleeve of the chuck with one hand and use the other hand to secure the tool. Rotate the sleeve counterclockwise far enough to accept the desired accessory. 3. Insert the accessory about 19 mm (3/4") into the chuck and tighten securely by rotating the chuck sleeve clockwise with one hand while holding the tool with the other. Your tool is equipped with an automatic spindle lock mechanism. This allows you to open and close the chuck with one hand. Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the tool for maximum tightness. To release the accessory, repeat steps 1 and 2 above. Belt Hook and Bit Clip (figure 1) warning: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. warning: To reduce the risk of serious personal injury, DO NOT suspend tool overhead or suspend objects from the belt hook. ONLY hang tool’s belt hook from a work belt. warning: To reduce the risk of serious personal injury, ensure the screw holding the belt hook is secure. important: When attaching or replacing the belt hook or bit clip, use only the screw (h) that is provided. Be sure to securely tighten the screw. The belt hook (g) and bit clip (i) can be be attached to either side of the tool using only the screw (h) provided, to accommodate left- or right- handed users. If the hook or bit clip is not desired at all, it can be removed from the tool.

(h) that holds it in place then reassemble on the opposite side. Be sure to securely tighten the screw. Operation Instructions for Use Warning: Always observe the safety instructions and applicable regulations. WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Proper Hand Position (figure 3) WARNING: To reduce the risk of serious personal injury, Always use proper hand position as shown. WARNING: To reduce the risk of serious personal injury, always hold securely in anticipation of a sudden reaction. Proper hand position requires one hand on the top of the drill (l) as shown, with the other hand on the main handle (m). Drill Operation (figure 4) WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the material. 1. Turn the collar (c) to the drill symbol. 2. Select the desired speed/torque range using the gear shifter to match the speed and torque to the planned operation. 3. For Wood, use twist bits, spade bits, power auger bits or hole saws. For Metal, use high- speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. 4. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting, but do not push hard enough to stall the motor or deflect the bit. 5. Hold tool firmly with both hands to control the twisting action of the drill. If model is not equipped with side handle, grip drill with one hand on the handle and one hand on the battery pack. caution: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip the drill firmly to control the twisting action and avoid injury. 6. IF DRILL STALLS, it is usually because it is being overloaded or improperly used. RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL — THIS CAN DAMAGE THE DRILL. 7. To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of the hole. 8. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming. 9. With variable speed drills there is no need to center punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep enough to drill without the bit skipping out. Hammerdrill Operation (figure 5) 1. Turn the collar (c) to the hammerdrill symbol. 2. Select the high speed setting by sliding the selector back (away from the chuck). Important: Use carbide-tipped or masonry bits only. 3. Drill with just enough force on the hammer to keep it from bouncing excessively or “rising” off the bit. Too much force will cause slower drilling speeds, overheating and lower drilling rate. 4. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit when drillling as this will cause clogging of the bit flutes and a slower drilling speed. 5. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the hole with tool stil running to help clear debris from the hole. NotE: A smooth, even flow of dust from the hole indicates proper drilling rate.

1. Select the desired speed/torque range using the dual range gear selector to match the speed and torque of the planned operation. 2. Turn the torque adjustment collar (c) to the desired position. Lower numbers indicate lower torque settings; higher numbers indicate higher torque settings. 3. Insert the desired fastener accessory into the chuck as you would any drill bit. 4. Make some practice runs in scrap or on unseen areas to determine the proper position of the clutch collar. 5. Always start with lower torque settings, then advance to higher torque settings to avoid damage to the workpiece or fastener. Maintenance Your DeWALT power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. The charger and battery pack are not serviceable. There are no serviceable parts inside. Lubrication Your power tool requires no additional lubrication. Cleaning Warning: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure. Warning: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Charger Cleaning Instructions WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Optional Accessories Warning: Since accessories, other than those offered by DeWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DeWALT, recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories. Protecting the Environment Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your DeWALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

recycling of DeWALT products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent by contacting your local DeWALT office at the address indicated in this manual. Alternatively, a list of authorised DeWALT repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com. Rechargeable Battery Pack This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before. At the end of its technical life, discard it with due care for our environment: • Run the battery pack down completely, then remove it from the tool. • Li-Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly.

13 毫米 (1/2")紧凑型充电式电钻/起子/冲击钻 DCD735, DCD785 恭喜！ 恭喜您选择了DEWALT工具。多年的经验和深入的产品开发创新使DEWALT成为专业电动工具使用者最可靠的合作伙伴 之一。 技术性数据 15 简体中文 DCD730,DCD780 电池组 DCB140 DCB141 DCB180 DCB181 DCB182 DCB183 DCB184 电池类型 锂电池 锂电池 锂电池 锂电池 锂电池 锂电池 锂电池 电压 VDC 14.4 14.4 18 18 18 18 18 容量 Ah 3.0 1.5 3.0 1.5 4.0 2.0 5.0 重量 kg 0.53 0.30 0.64 0.35 0.61 0.40 0.62 DCD730 DCD735 DCD780 DCD785 电压 VDC 14.4 14.4 18 18 电池类型 锂电池 锂电池 锂电池 锂电池 W 300 300 350 350 1 2 1 2 Nm 57 57 60 60 mm 13 13 13 13 35 35 38 38 13 13 13 13 kg 1.2 1.24 1.2 1.24 充电器 DCB105 电源电压 VAC 220V 电池类型 锂电池 大概充电时间 min 重量 kg 0.49 充电器 DCB115 电源电压 VAC 电池类型 大概充电时间 min 重量 kg min-1 min-1 0–550 0–1900 0–550 0–1900 0–600 0–2000 0–600 0–2000 min-1 min-1 – – 0–9350 0–32300 – – 0–10200 0–34000 mm mm mm 13 – 13 – 30 （1.5安培电池组） 55 （3.0安培电池组） 70 （4.0安培电池组） （1.3安培电池组） （3.0安培电池组） 220V 锂电池 22 45 0.5 22 （1.5安培电池组） 30 （2.0安培电池组） 60 （4.0安培电池组） 75 （5.0安培电池组）

通用安全警告 。 。 。 。 警告！阅读随电动工具提供的所有安全 警告、说明、图示和规定。不遵照以下所 列说明会导致不遵照以下所列说明会导致。 保存所有警告和说明书以备查阅 警告中的术语“电动工具”指市电驱动（有线）电动工 具或电池驱动（无线）电动工具。 a) b) 工作场地的安全 电气安全 保持工作场地清洁和明亮。杂乱和黑暗的场地 会引发事故。 不要在易爆环境，如有易燃液体、气体或粉尘 的环境下操作电动工具。电动工具产生的火花会 点燃粉尘或气体。 操作电动工具时，远离儿童和旁观者。注意力 不集中会使你失去对工具的控制。 电动工具插头必须与插座相配。绝不能以任何方 式改装插头。需接地的电动工具不能使用任何转 换插头。未经改装的插头和相配的插座将降低电 击风险。 避免人体接触接地表面，如管道、散热片和冰箱。 如果你身体接触接地表面会增加电击风险。 不得将电动工具暴露在雨中或潮湿环境中。水 进入电动工具将增加电击风险。 1） 2） 3） 1） 2） 3 ） c) d) 人身安全 不得滥用软线。绝不能用软线搬运、拉动电动 工具或拔出其插头。使软线远离热源、油、锐 边或运动部件。受损或缠绕的软线会增加电击 风险。 当在户外使用电动工具时，使用适合户外使用 的延长线。适合户外使用的电线将降低电击风 险。 如果无法避免在潮湿环境下操作电动工具，应 使用带有剩余电流装置（RCD）保护的电源。 RCD的使用可降低电击风险。 4） 5） 6） 保持警觉，当操作电动工具时关注所从事的操作 并保持清醒。当你感到疲倦，或在有药物、酒精 或治疗反应时，不要操作电动工具。在操作电动 工具时瞬间的疏忽会导致严重人身伤害。 使用个人防护装置。始终佩戴护目镜。 。防护装 置，诸如适当条件下使用防尘面具、防滑安全鞋、 安全帽、听力防护等装置能减少人身伤害。 防止意外起动。在连接电源和/或电池盒、拿 起或搬运工具前确保开关处于关断位置。手指 放在开关上搬运工具或开关处于接通时通电会 导致危险。 在电动工具接通之前，拿掉所有调节钥匙或扳 手。遗留在电动工具旋转零件上的扳手或钥匙 会导致人身伤害。 手不要过分伸展。时刻注意立足点和身体平衡。 这样能在意外情况下能更好地控制住电动工具。 着装适当。不要穿宽松衣服或佩戴饰品。让你 的头发和衣服远离运动部件。宽松衣服、佩饰 或长发可能会卷入运动部件。 如果提供了与排屑、集尘设备连接用的装置， 要确保其连接完好且使用得当。使用集尘装置 可降低尘屑引起的危险。 1） 2） 3） 4） 5） ） 6 7） 不要因为频繁使用工具而产生的熟悉感而掉以 轻心，忽视工具的安全准则。某个粗心的动作 可能在瞬间导致严重的伤害。 8） 电动工具使用和注意事项 1） 2） 3） 16 简体中文 不要勉强使用电动工具，根据用途使用合适的 电动工具。选用合适的按照额定值设计的电动 工具会使你工作更有效、更安全。 如果开关不能接通或关断电源，则不能使用该 电动工具。不能通过开关来控制的电动工具是危 险的且必须进行修理。 在进行任何调节、更换附件或贮存电动工具之 前，必须从电源上拔掉插头和／或卸下电池包 (如可拆卸）。这种防护性的安全措施降低了电 动工具意外起动的风险。

请保存这些说明：本手册包含重要的DCB105和DCB115 电池充电器安全和操作说明。 将闲置不用的电动工具贮存在儿童所及范围之 整到位或卡住，检查零件破损情况和影响电动 工具运行的其他状况。如有损坏，应在使用前 修理好电动工具。许多事故是由维护不良的电 维护电动工具及其附件。检查运动部件是否调 按照使用说明书，并考虑作业条件和要进行的 当电池包不用时，将它远离其他金属物体，例 在滥用条件下，液体可能会从电池组中溅出， 5）不要使用损坏或改装过的电池包或工具。损坏 应避免接触。如果意外碰到液体，用水冲洗。 如果液体碰到了眼睛，还要寻求医疗帮助。 从电池中溅出的液体可能会发生腐蚀或燃烧。 或改装过的电池组可能呈现无法预测的结果， 导致着火、爆炸或伤害。 6）不要将电池包暴露于火或者高温中。电池包暴 露于火或高于130℃的高温中可能导致爆炸。 如回形针、硬币、钥匙、钉子、螺钉或其他小 金属物体，以防电池包一端与另一端连接。电 池组端部短路会引起燃烧或着火。 8）保持手柄和握持表面干燥、清洁，不得沾有油 仅使用生产者规定的充电器充电。将适用于某 仅使用配有专用电池包的电动工具。使用其他 作业来选择电动工具、附件和工具的刀头等。 脂。在意外的情况下，湿滑的手柄不能保证握持 种电池包的充电器用到其他电池包时可能会发生 电池包可能会产生伤害和着火危险。 着火危险。 保持切削刀具锋利和清洁。维护良好地有锋利 外，并且不允许不熟悉电动工具和不了解这些 说明的人操作电动工具。电动工具在未经培训 电池式工具使用和注意事项： 1）让专业维修人员使用相同的备件维修电动工具。 这将保证所维修的电动工具的安全。 2）决不能维修损坏的电池包。电池包仅能由生产 者或其授权的维修服务商进行维修。 维修 电钻/起子/冲击钻的附加安全细则 e) f) 当在钻削附件可能触及暗线的场合进行操作时，要通 过绝缘握持面握持工具。钻削附件碰到带电导线会使 工具外露金属零件带电而使操作者遭受电击。 在紧固件可能触及暗线进行操作时，要通过绝缘握 持面来握持工具。紧固件碰到带电导线会使工具外 露的金属零件带电从而使操作者受到电击。 请佩戴安全护目镜或其他护目装备。冲击或钻孔会 导致碎片飞散。飞散的颗粒会对眼睛造成永久性伤 害。 钻头和工具会在使用过程中发热。接触时请佩戴手 套。 带耳罩进行冲击作业。暴露于噪声环境会导致失聪。 使用辅助手柄。失控会导致人身伤害。 工具使用前应得到适当支撑。由于工具输出转矩 大，运行时没有适当支撑会失控导致人身伤害。

x 电池组或充电器故障 • • • • • • • • • • • • 电源线故障 •• •• •• •• •• •• 充电状态:DCB115 充电中 已完全充电 热/冷电池组延迟* D C B 1 4 1 、 10.8 V, 14.4 V DCB184）电池组。 （D C B 1 2 1、D C B 1 4 0、 DCB183 和 DCB105 和 DCB115 和18 V D C B 1 8 0、DCB181、DCB182、

DCD780 DCD785 使用 18 DCB140、DCB141、DCB180、DCB181、DCB182 DCB183 或DCB184 电池组都可以使用。更多信息， 请参阅技术性数据。 如果电子保护系统处于运作状态，该工具将自动停止运 转。如果发生这种情况，请将锂离子电池放在充电器上 直到完全充电。 XR锂离子电池工具的设计带有防止电池超载、过热或深 度放电的电子保护系统。 热/冷电池延迟 当充电器检测到电池太热或太冷时，它会自动启动热/冷 电池延迟模式，暂停充电，直到电池达到适当的温度， 然后自动切换到电池组充电模式。此功能可确保电池拥 有最长的寿命。

废弃电池请回收。 禁止焚烧电池组。 锂离子电池组充电。 充电时间，请参阅技术性数据。 只能在室内使用。 警告：禁止改装电动工具或其任何部分。 否则可能导致损失或人身伤害。 说明(图1) 触发开关 正转/反转控制按钮 扭矩调节轴环 变速杆 工作灯 无键夹头 皮带扣 安装螺钉 钻头夹具 电池组 电池释放按钮. a. b. c. d. e. f. g. h. i. j. k. 本产品不适合身体、感官或心智能力有缺陷以及缺 乏经验、知识或技能的人（包括儿童）使用，除非 有人负责他们的安全监督。请勿将儿童单独留在存 放本产品的地方。 您的DEWALT充电器按IEC60335双重绝 缘，因此无需接地线。 ● 电器安全 电动机只有一个工作电压。请务必检查电池组的电压是 否和铭牌上的电压一致。另外，确保充电器电压和电源 对应。 使用延长线 除非绝对必要，否则不应使用延长线。请使用适合您的 充电器电源输入的合格延长线（见技术性数据）。导线 的最小尺寸为1mm2 ，最大长度为30m。 当使用电缆卷筒时，请务必完全卷出电缆。 电源线损坏时必须用DEWALT服务机构专门制备的电线 更换。 预期用途 这些电钻/起子/冲击钻是为专业的钻孔、冲击钻孔、起子 用途而设计的。 请勿在潮湿环境中或有易燃液体或气体的环境中使用。 该电钻/起子/冲击钻是专业的电动工具。 请勿让儿童接触工具。缺乏经验的操作员需要在监督下 使用此工具。 简体中文 禁止用导电物体碰触。 禁止给损坏的电池组充电。 禁止暴露于水中。 只使用DEWALT电池组。其他电池组可能 会爆炸，造成人身伤害和损害。 故障电源线。

正转/反转控制按钮(图1) 正转/反转控制按钮（b）确定工具方向，也有锁止按钮的 功能。 选择向前旋转时，释放触发开关，按下工具右侧的正转/ 反转控制按钮。 选择反向旋转时，按下工具左侧的正转/反转控制按钮。 控制按钮的中心位置会将工具锁定在关闭状态。改变控 制按钮的位置时，确保触发开关处于释放状态。 注意：改变旋转方向后第一次运行该工具时，您可能会 在启动时听到“啪嗒”声。这是正常现象，并不代表出 现故障。 扭矩调节轴环(图1) 您的工具带有可调扭矩起子功能用于拧紧和拆除不同形 状和大小的紧固件，以及为砖石钻孔的冲击钻功能。轴 环（c）周围有数字和钻头符号，在某些机型上，还有冲 击钻符号。这些数字是用来设置夹具的扭矩范围。轴环 上数字越大，扭矩和可驱动的紧固件就越大。选择任何 一个数字时，旋转轴环直到所需的数字与箭头对齐。 工作灯(图1) 触发开关（a）的上方有一工作灯。挤压触发开关即可激 活工作灯。从触发开关到释放后，工作灯照明状态将最 大停留20秒。 注意：工作灯是用于照明紧邻的工作表面，不能当作手 电筒使用。 您的工具配有无键夹头（f）。夹头带有一旋转套筒，用 于夹头的单手操作。要插入钻头或其他部件时，请按下列 步骤操作： 无键单套夹头(图7-9) 警告：禁止通过抓住夹头的前部并启动工 具来拧紧钻头（或任何其它配件）。这会 损坏夹头并导致人身伤害。更换配件时， 切记锁定触发开关，并将工具和电源断 开。 警告：确保启动工具前，紧固钻头。松弛 的钻头可能从工具上弹出，引起人身伤 害。 1. 2. 关闭工具和断开电源。 用一只手抓住夹头的黑色外套，并用另一只手固定 工具。逆时针旋转套筒使其足以容纳所需配件。 变速触发开关(图1) 开启该工具请按下触发开关（a）。关闭工具请释放触发 开关。您的工具配备有制动系统。触发开关完全释放时 钻头夹将停止运作。 注意：不建议在变速范围内连续使用工具。否则可能会 损坏开关。请尽量避免。 1. 2. 按电池释放按钮（k），并用力将电池组从工具手柄 中拉出。 按本手册充电器部分所述将电池组插入充电器中。 从工具上移除电池组 21 简体中文 插入/拆除电池组(图2) 注意：为达到最佳效果，请确保电池组完全充电。 将电池组安装到工具手柄中: 组装和调试 警告：组装和调试前，请务必拆下电池组。 插入或取出电池之前，务必关掉工具。 警告：只使用DEWALT电池组和充电器。 1. 2. 将电池组（j）对齐工具手柄内的轨道（图 2）。 将电池组滑入手柄内，使其牢牢地固定在工具内， 并确保不会脱离。 双档调速(图1) 您的起子/电钻的双档调速功能使你能够调档，从而获得 更大的灵活性。 注意：工具运行时切勿换挡。换挡前电钻要完全停止运 作。如果换档出现问题，确保双档变速杆要么是彻底推 到前部或完全推到后部。 1. 2. 要选择转速1(高扭矩设定)时，关闭工具使其停止运 作。向前滑动变速杆（d）（朝向夹头）。 要选择转速2(高扭矩设定)时，关闭工具使其停止运 作。向后滑动变速杆（远离夹头）。

住工具，用另一只手顺时针旋转夹头套筒，使其紧 固。您的工具配备自动主轴锁定机制。这可以让你 用一只手打开和关闭夹头。 请务必使用一只手握住夹头套筒，一只手握住工具，紧 固到最大限度。 要释放配件，请重复上述步骤1和步骤2.

维护 您的DEWALT电动工具设计精良，可以长期使用，只需 最低限度的维护。连续令人满意的操作取决于适当的工 具护理和定期清洁。 润滑 您的电动工具无需另行润滑。 充电器和电池都不能被维修，里面没有可以维修的部 件。 警告：为了减少严重人身伤害的危险， 调整或拆卸/安装附件或配件前，请务必 关闭工具，断开电池组。偶然的启动可能 导致人身伤害。 环境保护 分类回收。该产品不能与普通生活垃圾一 起处理。 使用过的产品和包装的分类回收能够得以 再循环和再利用。再生材料的再利用有助 于防止环境污染，并降低对原材料的需 求。 如果有一天您发现您的DEWALT产品需要更换，或不能继 续使用，禁止把它和生活垃圾一起处理。请单独分类回 收。 市政废物处理场或您购买新产品的零售商处，地方性法规 可能要求电器产品和生活垃圾分开回收。 23 简体中文 注意：如果钻屑平稳均匀地从孔中清除出来，则表示钻 孔速度适当。 1. 2. 3. 4. 5. 使用双档换档变速杆选择所需的转速/转矩范围，以 配合计划的运作速度和转矩。 转动扭矩调节轴环（c）到所需位置。数字越小表 示扭矩设置越低；数字越大表明转矩设置越高。 把所需的紧固件配件插入夹头，与安装钻头的操作 一样。 在废料上或在不可见的区域做些练习，确定离合器 环的适当位置。 启动时，始终采用较低的扭矩设置，然后升高到较 高的扭矩设置，以避免损坏工件或紧固件。 螺丝起子操作(图6) 4. 5. 直线钻进，使工件和钻头成直角。钻进时，不得对 钻头施加侧向力，这会堵塞屑槽、降低钻进速度。 钻深孔时，如果冲击钻的速度开始下降了，请把钻 头从孔中拉出一部分，同时保持工具运行，以帮助 钻屑从洞口清除出来。 清洁 可选配件 请向您的经销商咨询更多关于合适配件的信息。 充电器清洁说明 警告：通风口和周围积聚可见的粉尘 时，请用干燥的空气吹走主机外壳内的粉 尘和灰尘。执行此过程时，需戴上经认可 的护目装备和防尘口罩。 警告：触电危险。清洁前，请把充电器 从交流电源插座上断开。可用布或非金属 软刷清除充电器外部的污垢和油脂。禁止 使用水或任何清洁剂。 警告：由于除了DEWALT提供的配件， 其他配件都未经此产品兼容性测试，本工 具若使用此类配件将存在安全隐患。为了 减少受伤的风险，本产品只可使用 DEWALT推荐的配件。 警告：切勿使用溶剂或其他烈性化学制 品来清洁工具的非金属零件。这些化学物 质可能会削弱这些部位使用的材料。请用 布蘸温和的肥皂水擦拭。切勿让任何液体 进入工具，禁止让工具的任何部分在液体 中浸泡。 DEWALT提供设施收集和回收使用寿命到期的DEWALT 产品。要充分利用这项服务，请将产品返回任何授权的 维修代理，他们将代表我们回收您的产品。 您可以在本手册查找离您最近的授权维修代理的位置， 与本手册注明的当地DEWALT办事处联系。另外，也可 以登陆以下网址查看授权DEWALT维修代理商清单，以 及我们的售后服务的详细资料和联系方式： www.2helpU.com.

产 地:江苏苏州

鋰電充電式13mm電鑽起子機 鋰電充電式13mm三用震動電鑽起子機 DCD735, DCD785 恭喜！ 恭喜您選擇了DEWALT工具。多年的經驗和專業的產品開發創新使DEWALT成為專業電動工具使用者最可靠的合作夥伴 之一。 技術性資料 25 繁體中文 DCD730,DCD780 電池組 DCB140 DCB141 DCB180 DCB181 DCB182 DCB183 DCB184 電池類型 鋰電池 鋰電池 鋰電池 鋰電池 鋰電池 鋰電池 鋰電池 電壓 VDC 14.4 14.4 18 18 18 18 18 Ah 3.0 1.5 3.0 1.5 4.0 2.0 5.0 重量 kg 0.53 0.30 0.64 0.35 0.61 0.40 0.62 DCD730 DCD735 DCD780 DCD785 電壓 VDC 14.4 14.4 18 18 電池類型 鋰電池 鋰電池 鋰電池 鋰電池 W 300 300 350 350 1 2 1 2 Nm 57 57 60 60 mm 13 13 13 13 35 35 38 38 13 13 13 13 kg 1.2 1.24 1.2 1.24 充電器 DCB105 電源電壓 VAC 110V 電池類型 鋰電池 大概充電時間 min 重量 kg 0.49 充電器 電源電壓 VAC 電池類型 大概充電時間 min 重量 kg min-1 min-1 0–550 0–1900 0–550 0–1900 0–600 0–2000 0–600 0–2000 min-1 min-1 – – 0–9350 0–32300 – – 0–10200 0–34000 mm mm mm 13 – 13 – 30 （1.5安培電池組） 55 （3.0安培電池組） 70 （4.0安培電池組） 0.5 DCB115 110V 鋰電池 22 （1.3安培電池組） 22 （1.5安培電池組） 30 （2.0安培電池組） 45 （3.0安培電池組） 60 （4.0安培電池組） 75 （5.0安培電池組）

2 ) 電器安全 保持工作場地清潔和明亮，雜亂或陰暗的地方 容易引發事故。 禁止在易爆環境中操作電動工具，如有易燃液 體、氣體或粉塵的環境。電動工具產生的火花 會點燃粉塵或煙霧。 操縱電動工具時禁止兒童和旁觀者靠近。干擾 可能會導致您操作不當。 電動工具插頭必須與同規格的插座搭配。禁止 以任何方式改裝插頭。需要接地的電動工具不 能使用任何轉接插頭。原廠所附的插頭與同規 格的插座將減少觸電的危險。 避免人體與接地表面接觸, 如管道、散熱器、爐 灶、冰箱。如果您的身體接地，觸電危險性會 增加。 請勿將電動工具暴露在雨中或潮濕環境中。電 動工具進水將增加觸電危險。 a） b） c） a） b） c） 3 ) 人身安全 切勿濫用電線。切勿使用電源線搬運、拉動或 拔下電動工具。保持電源線遠離熱源、油、銳 邊或運動部件。受損或纏繞的電線會增加觸電 的危險。 在室外操作電動工具時，請使用適合戶外使用 的外接電線。適合戶外使用的電線會減少觸電 的危險。 如果必須得在潮濕的地方操作電動工具，請使 用剩餘電流裝置(RCD)保護的電源。RCD的使 用減少了觸電的危險. d） e） f） 保持警覺，操作電動工具時注意操作，保持清 醒。切勿在疲倦或治療時或在藥物或酒精的影 響下使用電動工具。操作電動工具時注意力不 集中可能會導致嚴重的人身傷害。 使用個人防護裝備。始終佩戴護目鏡。適當的 條件下使用防護裝備將減少人身傷害，如防塵 口罩、防滑安全鞋、安全帽、聽力保護設備。 防止意外啟動。在連接電源或電池組之前以及 拿起或攜帶工具之前請確保開關處於關閉位 置。攜帶電動工具時把手指放在開關上或充電 時開關處於打開位置會造成人身危險。 打開工具前拆下所有調整鍵或扳手。連接在電 動工具旋轉零件上的扳手或調整鍵可能導致人 身傷害。 禁止手伸得太長，時刻注意腳下和身體平衡。 這樣在意外情況下能更好地控制電動工具。 穿著得當。操作電動工具時切忌穿寬鬆的衣服 或佩戴首飾。讓您的頭髮、衣服和手套遠離運 動的零件。寬鬆的衣服、首飾或長髮可能會捲 入運動零件中。 如果有提供連接排屑集塵設備的裝置，請確保 這些裝置連接完好，使用正常。集塵可減少與 粉塵有關的危害。 a） b） c） d） e） f） g） 4 ) 電動工具的使用和注意項 禁止強制使用電動工具。根據用途，使用正確 的電動工具。正確的電動工具在設計的額定功 率下能更好更安全地完成工作。 禁止使用開關不能打開和關閉的電動工具。任 何不能用開關控制的電動工具都很危險，必須 進行修理。 調整、更換附件或儲存電動工具前，請將電動 工具和電源插頭或電池組斷開。這種預防性安 全措施能減少意外啟動電動工具的風險。 a） b） c） 26 繁體中文 定義：安全方針 d）將電動工具儲存在兒童不能拿到的地方，禁止 不熟悉電動工具或本說明書的人操作電動工 具。讓未經訓練的用戶操作電動工具是很危險 的。

製造年份 針對所有電池充電器的 重要安全說明 本手冊包含重要的DCB105和DCB115 電池充電器安全和操作說明。 5 ) 電池工具使用和注意事項 6 ) 服务 佩戴安全護目鏡或其他保護眼睛的設備。錘擊和鑽 孔作業會導致碎片亂飛。四射的小型物可能會造成 永久性的眼部損傷。 配件和工具可能會在操作過程中變熱。執行錘鑽和 金屬鑽孔等這些會產生熱的作業時，請戴上手套。 ● ● ●禁止長時間操作本工具。錘鑽的運動所引起的振動 可能會傷害您的手和胳膊。使用手套會提供額外的 緩衝，頻繁的休息也能限制傷害。 通風口通常包括運動部件，應儘量避免。寬鬆的衣 服、首飾或長髮可能會捲入運動零件中。 ●

電池（DCB121、DCB140、DCB141 、 DCB180、DCB181 、DCB182 、 DCB183 和 DCB184）電池組。 DCB105 和 DCB115 18V 和20 V 為了確保鋰電池的最佳性能和壽命，請在第一次 使用前將電池組完全充電。 充電程式(圖2) 充電過程 關於電池組的充電狀態，請參閱下表。 充電器不會為故障的電池組充電。充電器會透過不亮燈或 顯示電池組故障或充電器閃爍模式來代表電池組故障。 注意：這也可能意味充電器有故障。 如果充電器提示有故障存在，請將充電器和電池組送到授 權的服務中心進行測試。 1. 2. 3. 插入電池組前請將充電器插入到合適的110~120V插 座。 將電池組（j）插入到充電器中，確定電池組完全就 位。紅色(充電)指示燈將閃爍不斷，表明充電過程 已經開始。 紅色燈的持續亮起表示充電完成。此時電池組已完 全充電，此時您可使用電池組或將電池組留在充電 器上。 繁體中文 充電狀態:DCB105 充電 –– –– –– –– 電力全滿 ––––––––––––––––– 電池組熱/冷延遲 –– • –– • –– • –– • x 電池組或充電器故障 • • • • • • • • • • • • 電源線故障 •• •• •• •• •• •• 充電狀態:DCB115 充電中 電力全滿 電池組熱/冷延遲*

請參閱技術性資料。 充電器和電池上的標籤 除了在本手冊中使用的標誌，充電器和電池組的標籤還 包括： 注意：電池組儲存時不能處於電荷完全耗盡的狀態。在 使用電池組前需要充電。 存儲建議 1. 2. 最好將電池存放在陰涼、乾燥、遠離陽光直射、不 會過熱或過冷的地方。為了獲得最佳的電池性能和 壽命，在不使用時請將電池組存儲在室溫下。 長期儲存時，建議將完全充電的充電器儲存在陰 涼、乾燥的地方，以達到電池組最佳的效果。 29 禁止在易爆環境中充電或使用電池組，如有易燃液 體、氣體或粉塵的環境。插入或取出電池組時可能 會點燃粉塵或煙霧。 切勿將電池組強行插入充電器。禁止將電池組插入 不相容的充電器，禁止任何方式改裝電池組，這種 操作可能會導致電池組破裂，造成嚴重的人身傷 害。 只使用指定的DEWALT充電器為電池組充電。 禁止把電池組浸泡在水或其他液體中，或潑灑水或 其他液體到電池組上。 禁止在溫度可能達到或超過40˚C(105°F)的地方(如 夏天戶外的棚子或金屬建築物中)儲存或使用工具和 電池組。 為達到最佳效果，請確保電池組在使用前完全充 電。 ● ● ● ● ● ● 即使在電池組嚴重受損或完全磨損的情況下，也請 勿焚燒電池組。電池可能在火中爆炸。鋰電池組被 燒毀時會產生有毒氣體和材料。 ● 如果電池裏的東西與皮膚接觸，請立即用溫和肥皂 和水沖洗接觸的地方。如果電池液進入眼睛，用水 清洗睜開的眼睛15分鐘或直到刺激感消失。如果需 要醫療救助，請告知醫護人員：電池的電解質是由 有機碳酸鹽和鋰鹽的混合物組成。 電池裏的成分可能刺激呼吸道。此時請提供新鮮空 氣。如果症狀仍然存在，請就醫。 ● ● 針對所有電池充電器的 重要安全說明 在要求更換電池組時，請務必附上目錄號碼和電壓。 貨箱中的電池組是未完全充電的。在使用電池和充電器 之前，請閱讀下面的安全說明，然後按照充電程式進行 操作。 請閱讀所有說明。 冷電池組充電速率是溫熱的電池組充電速率的一半左 右。電池組在整個充電週期的充電速度都會較慢，即使 電池升溫也不會返回到最高速度。 鋰電池的安全說明 警告：無論任何理由，都禁止打開電池 組。電池組外殼破裂或損壞時，禁止將電 池組插入充電器。請勿擠壓、跌落或損壞 電池組。禁止使用受過強烈衝擊、跌落、 碾壓或以任何其他方式(如被釘子穿破、 受到錘子的重擊)被損壞的電池或充電 器。否則會引起觸電。損壞的電池組應交 回服務中心回收。 注意：在不使用時，請將工具放置在不會 引起人摔倒的穩定表面上。一些帶大型電 池組的工具會電池端朝下直立，很容易被 撞翻。 繁體中文 熱/冷電池延遲 當充電器檢測到電池過熱或過冷時，它會自動啟動過熱/ 過冷電池延遲模式，暫停充電，直到電池達到適當的溫 度，然後自動切換到電池組充電模式。此功能可確保電 池擁有最長的壽命。 XR鋰電池工具的設計帶有防止電池超載、過熱或深度放 電的電子保護系統。 如果電子保護系統處於運作狀態，該工具將自動停止運 轉。如果發生這種情況，請將鋰電池放在充電器上直到 完全充電。

廢棄電池請回收。 禁止焚燒電池組。 鋰電池組充電。 充電時間，請參閱技術性資料。 只能在室內使用。 警告：禁止改裝電動工具或其任何部分， 否則可能導致損失或人身傷害。 說明(圖1) 觸發開關 正轉/反轉控制按鈕 扭矩調整卡環 變速杆 工作燈 無鍵夾頭 皮帶扣 安裝螺釘 鑽頭夾具 電池組 電池釋放按鈕. a. b. c. d. e. f. g. h. i. j. k. 本產品不適合身體、感官或心智慧力有缺陷以及缺 乏經驗、知識或技能的人(包括兒童)使用，除非有 人負責他們的安全監督。請勿將兒童單獨留在存放 本產品的地方。 ● 電器安全 電動機只有一個工作電壓。請務必檢查電池組的電壓是 否和銘牌上的電壓一致。另外，確保充電器電壓和電源 對應。 使用延長線 除非絕對必要，否則不應使用延長線。請使用適合您的 充電器電源輸入的合格延長線(見技術性資料)。導線的 最小尺寸為1mm2，最大長度為30m。 當使用電纜捲筒，請務必完全卷出電纜。 電源線損壞時必須用DEWALT服務機構專門製備的電線 更換。 預期用途 這些電鑽/起子/錘鑽是為專業的鑽孔、衝擊鑽孔、起子用 途而設計的。 請勿在潮濕環境中或有易燃液體或氣體的環境中使用。 這些電鑽/起子/錘鑽是專業的電動工具。 請勿讓兒童接觸工具。缺乏經驗的操作員需要在監督下 使用此工具。 繁體中文 禁止用導電物體碰觸。 禁止給損壞的電池組充電。 禁止暴露于水中。 只使用DEWALT電池組。其他電池組可能 會爆炸，造成人身傷害和損害。 您的DEWALT充電器按IEC60335雙重絕緣， 因此無需接地線。 熱/冷電池延遲。 故障電池組或充電器。 故障電源線。

功能。 選擇向前旋轉時，釋放觸發開關，按下工具右側的正轉/ 反轉控制按鈕。 選擇反向旋轉時，按下工具左側的正轉/反轉控制按鈕。 控制按鈕的中心位置會將工具鎖定在關閉狀態。改變控 制按鈕的位置時，確保觸發開關處於釋放狀態。 注意：改變旋轉方向後第一次運行該工具時，您可能會 在啟動時聽到“啪嗒”聲。這是正常現象，並不代表出 現故障。 扭矩調整卡環(圖1) 您的工具帶有可調扭矩起子功能用於鎖和拆除不同形狀 和大小的緊固件，以及為磚石鑽孔的錘鑽功能。扭力環 (c)周圍有數位和鑽頭符號，在某些機型上，還有錘鑽符 號。這些數字是用來設置夾具的扭矩範圍。扭力環上數 字越大，扭矩和可驅動的緊固件就越大。選擇任何一個 數字時，旋轉扭力環直到所需的數字與箭頭對齊。 LED內置工作燈(圖1) 觸發開關( a )的上方有一工作燈。擠壓觸發開關即可啟 動工作燈。從觸發開關到釋放後，工作燈照明狀態將 最大停留20秒。 注意：工作燈是用於照明緊鄰的工作表面，不能當做 手電筒使用。 您的工具配有無鑰匙夾頭(f)。夾頭帶有一個旋轉套筒， 用於夾頭的單手操作。要插入鑽頭或其他部件時，請按 下列步驟操作。 無鑰匙夾頭(圖7-9) 警告：禁止通過抓住夾頭的前部並啟動 工具來擰緊鑽頭(或任何其他配件)。這 會損壞夾頭並導致人身傷害。更換配件 時，切記鎖定觸發開關，並將工具和電源 斷開。 警告：確保啟動工具前，緊固鑽頭。鬆 弛的鑽頭可能從工具上彈出，引起人身傷 害。 1. 2. 關閉工具和斷開電源。 用一隻手抓住夾頭的黑色外套，並用另一隻手固 定工具。逆時針旋轉套筒使其足以容納所需配 件。 變速觸發開關(圖1) 開啟該工具請按下觸發開關( a )。關閉工具請釋放觸發開 關( a )。您的工具配備有制動系統。觸發開關完全釋放時 鑽頭夾將停止運作。 注意：不建議在變速範圍內連續使用工具。否則可能會 損壞開關。請儘量避免。 1. 2. 按電池釋放按鈕(k)，並用力將電池組從工具手柄中 拉出。 按本手冊充電器部分所述將電池組插入充電器中。 從工具上移除電池組 繁體中文 插入/拆除電池組(圖2) 注意：為達到最佳效果，請確保電池組完全充電。 將電池組安裝到工具手柄中。 組裝和調試 警告：組裝和調試前，請務必拆下電池組。 插入或取出電池之前，務必關掉工具。 警告：只使用DEWALT電池組和充電器。 1. 2. 將電池組( j )對齊工具手柄內的軌道(圖2)。 將電池組滑入手柄內，使其牢牢地固定在工具內， 並確保不會脫離。 二段調速(圖1) 您的起子/電鑽的二段調速功能使你能夠調速，從而獲 得更大的靈活性。 注意：工具運行時切勿換擋。換擋前電鑽要完全停止 運作。如果換檔出現問題，確保二段調速杆要麼是徹 底推到前部或完全推到後部。 1. 2. 要選擇轉速1(高扭矩設定)時，關閉工具使其停止 運作。向前滑動變速杆(d)(朝向夾頭)。 要選擇轉速2(高扭矩設定)時，關閉工具使其停止 運作。向後滑動變速杆(遠離夾頭)。 31

可使用提供的螺釘(h)將皮帶扣(g)和鑽頭夾具(i)裝到工具 的任意一側，以方便習慣左手操作或習慣右手操作的用 戶使用。無需皮帶扣和鑽頭夾具時，可以從工具上拆 除。 要拆除皮帶扣和鑽頭夾具時，卸下固定它們的螺絲(h)， 然後在另一邊重新裝上。 切記要擰緊螺釘。 正確的手持方式如圖所示，一隻手應該放在電鑽(l)頂 部，另一隻手放在在主手柄(m)上。 操作 使用說明 正確的手持方式(圖3) 警告：請務必遵守安全說明和適用的法 規。 警告：為了減少嚴重人身傷害的危險， 調整或拆卸/安裝附件或配件前，請務必 關閉工具，斷開電源。 警告：為了減少嚴重人身傷害的危險， 請務必使用如圖所示的正確的手持方式。 警告：為了減少嚴重人身傷害的風險， 請務必緊握住工具以防突發狀況。 6. 7. 8. 9. 電鑽停轉通常是因為超載或使用不當。請立即鬆開 觸發開關，取出鑽頭，並確定停轉原因。切勿通過 點動觸發開關來啟動停轉的電鑽，這樣可能會損壞 電鑽。 為了儘量減少停轉故障，避免鑽頭在材料中折斷， 請降低對電鑽的壓力，讓鑽頭在孔的最後部分緩和 下來。 從成孔中拉出鑽頭時，請保持電機運行。這有助於 防止卡死。 使用變速電鑽時，無需中心沖定位。啟動時使用較 低速度，當鑽孔夠深可以防止跳鑽時，加力擠壓觸 發開關進行加速。 1. 2. 3. 轉動卡圈(c)到錘鑽標誌。 向後(遠離夾頭)滑動選擇開關選擇高速設置。 重要：僅可使用硬質合金或磚石鑽頭。 對錘鑽的用力應剛好防止過度回彈或“跳離”。用 力過猛會導致鑽孔速度減慢、過熱和降低轉速。 錘鑽操作(圖5) 注意：電鑽超載時會停止運轉，並導致 突然扭轉。請務必考慮到停轉的可能性。 握緊工具，控制扭轉效應並避免受傷。 繁體中文 警告：為了減少嚴重的人身傷害的風 險，確保固定皮帶扣子的螺釘是牢固的。 皮帶扣和鑽頭夾具(圖1) 警告：為了減少嚴重人身傷害的危險， 調整或拆卸/安裝附件或配件前，請務必 關閉工具電源，斷開電池組。 警告：為了減少嚴重人身傷害的危險， 請勿將工具懸掛在頭頂上方或用皮帶扣懸 掛物品。只可以使用工作皮帶懸掛工具的 皮帶扣。 重要：安裝或更換皮帶扣或鑽頭夾具時，只可以使用提 供的螺釘(h) 。切記要擰緊螺釘。 鑽孔操作(圖4) 警告：為了減少嚴重人身傷害的危險， 調試或拆卸/安裝附件或配件前，請務必 關閉工具，斷開電源。 1. 2. 3. 4. 5. 轉動扭力環(c)到鑽孔標誌。 使用變速杆選擇所需的轉速/轉矩範圍，以配合計畫 的運作速度和轉矩。 鑽木材時，應使用鐵工鑽頭、扁平鑽頭、電力螺旋 鑽頭或圓穴孔鋸。鑽金屬時，使用高速鋼鐵工鑽頭 或孔鋸。鑽金屬時使用切削潤滑劑。鑄鐵和黃銅是 例外。 用力方向始終與鑽頭成直線。施加鑽咬所需的壓力 不應過大，以免導致馬達失速或鑽頭傾斜。 用雙手緊握工具，控制鑽頭的扭轉效應。 如果該型 號沒有配備側手柄，請用一隻手握住電鑽手柄，另 一隻手握住電池組。 警告：為了減少人身傷害的危險，請確 保夾緊或固定工件,如果在薄材料上鑽 孔，請使用木材“襯墊”以防止材料損 壞。 32 3. 將配件插入夾頭約19mm(3/4")，收緊然後一隻手 握住工具，用另一隻手順時針旋轉夾頭套筒，使 其緊固。您的工具配備自動主軸鎖定機制。這可 以讓你用一隻手打開和關閉夾頭。 請務必使用一隻手握住夾頭套筒，一隻手握住工具， 緊固到最大限度。 要釋放配件，請重複上述步驟1和步驟2.

維護 您的DEWALT電動工具設計精良，可以長期使用，只需 簡單的基礎維護。連續令人滿意的操作取決於適當的工 具護理和定期清潔。 潤滑 您的電動工具無需另行潤滑。 充電器和電池都不能被維修。裏面沒有可以維修的部 件。 警告：為了減少嚴重人身傷害的危險， 調整或拆卸/安裝附件或配件前，請務必 關閉工具電源，斷開電池組。偶然的啟動 可能導致人身傷害。 環境保護 分類回收。該產品不能與普通生活垃圾一 起處理。 使用過的產品和包裝的分類回收能夠得以 再迴圈和再利用。再生材料的再利用有助 於防止環境污染，並降低對原材料的需 求。 如果有一天您發現您的DEWALT產品需要更換，或不能繼 續使用，禁止把它和生活垃圾一起處理。請單獨分類回 收。 所在地環保單位或您購買新產品的零售商處，根據廢棄物 清理法規定，電器產品和生活垃圾需分開回收。 33 繁體中文 注意：如果鑽屑平穩均勻地從孔中清除出來，則表示鑽 孔速度適當。 1. 2. 3. 4. 5. 使用二段轉速變速杆選擇所需的轉速/轉矩範圍， 以配合計畫的運作速度和轉矩。 轉動扭矩調整卡圈(c)到所需位置。數字越小表示扭 矩設置越低；數字越大表明轉矩設置越高。 把所需的緊固件配件插入夾頭，與安裝鑽頭的操作 一樣。 在廢料上或在不可見的區域做些練習，確定離合器 環的適當位置。 啟動時，始終採用較低的扭矩設置，然後升高到較 高的扭矩設置，以避免損壞工件或緊固件。 螺絲起子操作(圖6) 4. 5. 直線鑽進，使工件和鑽頭成直角。鑽進時，不得對 鑽頭施加側向力，這會堵塞屑槽、降低鑽進速度。 鑽深孔時，如果錘鑽的速度開始下降了，請把鑽頭 從孔中拉出一部分，同時保持工具運行，以幫助鑽 屑從洞口清除出來。 清潔 可選配件 請向您的經銷商諮詢更多關於合適配件的資訊。 充電器清潔說明 警告：通風口和周圍積聚可見的粉塵 時，請用乾燥的空氣吹走主機外殼內的粉 塵和灰塵。執行此過程時，需戴上經認可 的護目裝備和防塵口罩。 警告：觸電危險。清潔前，請把充電器 從交流電源插座上斷開。可用布或非金屬 軟刷清除充電器外部的污垢和油脂。禁止 使用水或任何清潔劑。 警告：由於除了DEWALT提供的配件， 其他配件都未經此產品相容性測試，本工 具若使用此類配件將存在安全隱患。為了 減少受傷的風險，本產品只可使用 DEWALT推薦的配件。 警告：切勿使用溶劑或其他烈性化學製 品來清潔工具的非金屬零件。這些化學物 質可能會削弱這些部位使用的材料。請用 布蘸溫和的肥皂水擦拭。切勿讓任何液體 進入工具，禁止讓工具的任何部分在液體 中浸泡。 DEWALT提供設施收集和回收使用壽命到期的DEWALT 產品。要充分利用這項服務，請將產品返回任何授權的 維修代理，他們將代表我們回收您的產品。 您可以在本手冊查找離您最近的授權維修代理的位置， 與本手冊注明的當地DEWALT辦事處聯繫。另外，也可 以登陸以下網址查看授權DEWALT維修代理商清單，以 及我們的售後服務的詳細資料和聯繫方式： www.2helpU.com.

可充電電池組 本長壽命電池組不能提供順利完成工作所需的電力時必 須進行充電。其技術壽命結束時，要謹慎處理，注意保 護環境： 耗盡電池組的電力，然後從工具上拆下。 鋰電池是可回收的。將它們送往您的經銷商處或當 地的回收站。回收的電池組將被妥善回收或處理。 ● ● 34 繁體中文 進口商:新加坡商百得電動工具(股)公司台灣分公司 地址:台北市士林區德行西路33號2樓 電話:02-28341741 總經銷商：永安實業股份有限公司 地址：新北市三重區新北大道二段137號 電話：02-29994633

–– • –– • –– • –– • x 문제 팩 또는 충전기 • • • • • • • • • • • • 문제 송전선 •• •• •• •• •• •• 충전 상태:DCB115 충전 중 완전 충전됨 냉/온 팩 지연*