Alula RE101 Manual 

with industry-leading wireless range and battery life. It is typically used to sense opening and closing of doors and windows, but can secure just about anything using its two external contact zones. It will alarm when the magnet is pulled away from the sensor or when an external contact is opened. Features •  Industry-leading wireless range and battery life •  One door window zone and two external contact zones •  Secure encrypted wireless transmissions •  5 year warranty Enroll by placing the panel into wireless enrollment mode and then sending an enrollment signal from the sensor. Enrollment Signal for Reed Switch •  Remove the battery tab and trip tamper to enroll reed switch and External 1 Install by mounting the sensor and magnet on a door or window using the mounting screw locations. Make sure to align the alignment marks on the sensor and magnet when mounting. Additionally, the sensor can be used with up to two external contacts. External Contacts •  Use normally-closed contacts because the door window sensor will transmit an alarm when it sees an external contact open •  Do not use end-of-line resistors •  Wire contact wires to one or both outside terminals, using the center terminal as common •  External 1 takes the place of the reed switch if installed •  External 2 is a different zone with a different ID •  To enroll, hold down tamper while inserting battery Mounting Screw Holes Use the panel installation guide to verify proper system setup. Door Window Sensor RE101, RE201, RE201T, RE301, RE601 I N S T A L L G U I D E I Resolution Compatibles Enrollment Signal for External Contact •  External 2 is enrolled by holding down tamper while installing battery

applied for over 10 seconds. Surface Preparation •  Clean the surface •  Ensure the mounting surface temperature is above 50 °F Wireless performance is optimized when mounted near the top of the door in a vertical orientation. OK BEST WRONG Wire an external contact by securing one wire to either the external 1 or external 2 port and the other wire to the common port. If both external contacts are used two wires will be inserted into the common port. Battery - + Cover Tamper rnal 1 m nal 1 Magnetic Reed Switch External 1 Terminal External 2 Terminal Center Common Terminal Tamper

X Axis Z Axis Non-Ferromagnetic Surface Nominal Mounting Distance X Axis - Make Break Y Axis - Make Break Z Axis - Make Break 1.00 inches (2.5 cm) 1.10 inches (2.8 cm) 1.30 inches (3.3 cm) 2.40 inches (6.1 cm) 2.55 inches (6.5 cm) 1.20 inches (3.0 cm) 1.35 inches (3.5 cm) Ferromagnetic Surface Nominal Mounting Distance X Axis - Make Break Y Axis - Make Break Z Axis - Make Break 0.50 inches (1.2 cm) 0.60 inches (1.5 cm) 0.65 inches (1.7 cm) 1.70 inches (4.3 cm) 1.75 inches (4.5 cm) 1.05 inches (2.7 cm) 1.10 inches (2.9 cm) Y Axis

first five (5) years, and portable products that are defective in their first two (2) years. IC NOTICE This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux cnr d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage, et (2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IC: 8310A-RE101 FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Alula could void the user’s authority to operate this equipment. FCC ID: U5X-RE101X TRADEMARKS Alula is a trademark owned by Alula Holdings, LLC. “Interlogix” is a trademark owned by United Technologies Electronic Controls Inc. Alula products will function with Interlogix systems. However, no Alula product is produced by, endorsed by, or is officially associated with Interlogix. Alula recommends verifying proper enrollment and operation, per control panel installation instructions, at installation. 3M and VHB are trademarks owned by 3M Company. Panasonic is a trademark owned by Panasonic Corporation. Specifications subject to change without notice Physical Housing Dimensions Weight with Battery Mounting Fastener 3.25 x 1.40 x 1.05 inches (8.3 x 3.6 x 2.7 cm) 1.90 ounces (54 grams) Four #6 screws (provided) Environmental Operating Temperature Maximum Humidity 32° to 120 °F (0° to 49 °C) 85% non-condensing relative humidity Sensor Specifications Frequency Replacement Battery Nominal Battery Life Battery Voltage Current Draw Transmitted Indications Max Wire Length on External Contacts 319.5 MHz One Panasonic® CR123A 10 to 15 years 3.0 VDC (Nominal), 2.2 VDC (Low) 20 mA (Maximum), 0.6 uA (Quiescent) Cover Tamper, Low Battery, Supervision 7.5 feet Certification RE101 FCC, IC Specifications 47-0004-01 • REV C • 2018-12-11 Tech Support Line • (888) 88-ALULA • (888) 882-5852 alula.net 01