Bosch HSG9483 Series Instruction Manual

Bosch Security Systems | 26 March 2004 HSG9483 Series | Instruction Manual | Installation 3. Feed-through Wiring Use feed-through mounts to feed cabling through the foot of the housing. a. Prior to mounting the camera, remove the two dome plugs located inside the housing (see FIGURE 6). Figure 6: Feed-through Wiring b. Screw the two 3/8in. NPT fittings into the foot of the housing. c. Pull the cabling through the fittings and into the housing. Tighten the fitting to 4.0 N.m to 4.5 N.m (35in.lb to 40in.lb). This torque rating is approximately 1 to 1-1/2 turns past the point where the f ...

Bosch Security Systems | 26 March 2004 4.8 Lens Wiring WARNING: For lens wiring, use only the cables specified under INSTALLATION, Cable Requirements. 1. Install the last 3/8in. NPT fitting into the remaining hole in the rear cap. 2. If installing a zoom lens, insert the lens control cable through the last fitting at the rear of the housing. Attach the lens wiring to the lens mating connector and connect it to the lens. If a mating connector is not available, connect directly to the lens cable. 3. Pull any excess wire out of the housing and tighten the fitting to 8.5 N.m to 9.0 N.m (75 ...

Bosch Security Systems | 26 March 2004 HSG9483 Series | Instruction Manual | Installation 4 INSTALLATION CAUTION: These units must be properly and securely mounted to a supporting structure capable of sustaining the unit weight. Use care when selecting mounts or pan/tilts (not supplied) for installation; the mounting surface and unit's weight should be carefully considered. 4.1 Tools Required • Small flat blade screwdriver • Phillips screwdriver (#1) • Adjustable wrench • Wire cutter/stripper/crimper tool 4.2 Cable Requirements Video Transmission (Coaxial) Cable Type: RG-59/U fo ...

3935 890 46712 04-13 | Updated March 26, 2004 | Data subject to change without notice. Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 USA Tel: 800-326-3270 Fax: 1-717-735-6560 www.boschsecuritysystems.com Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven The Netherlands Tele +31 40 27 80000 Bosch Security Systems Pte Ltd. 38C Jalan Pemimpin Singapore 577180 Republic of Singapore Tel: 65 (6) 319 3486 ...

Bosch Security Systems | 26 March 2004 e. Pull any excess wire out of the housing and tighten the fitting to 8.5.N.m to 9.0 N.m (75in.lb to 80in.lb). This torque rating is approximately 1 to 1-1/2 turns past the point where the fitting starts to grip the wire. Be sure to securely tighten all fittings to ensure a liquid-tight seal. Failure to do this could allow water to enter the housing and damage electronic parts, camera, and lens. f. Connect the supply power wires to the terminal block (see WIRING DIAGRAM in Table 1). Strip no less than 6mm (0.25in) and no more than 8mm (0.31in) of ...

Bosch Security Systems | 26 March 2004 HSG9483 Series | Instruction Manual | Installation 3. Feed-through Wiring Use feed-through mounts to feed cabling through the foot of the housing. a. Prior to mounting the camera, remove the two dome plugs located inside the housing (see FIGURE 6). Figure 6: Feed-through Wiring b. Screw the two 3/8in. NPT fittings into the foot of the housing. c. Pull the cabling through the fittings and into the housing. Tighten the fitting to 4.0 N.m to 4.5 N.m (35in.lb to 40in.lb). This torque rating is approximately 1 to 1-1/2 turns past the point where the f ...

Bosch Security Systems | 26 March 2004 HSG9483 Series | Instruction Manual | Installation 4 INSTALLATION CAUTION: These units must be properly and securely mounted to a supporting structure capable of sustaining the unit weight. Use care when selecting mounts or pan/tilts (not supplied) for installation; the mounting surface and unit's weight should be carefully considered. 4.1 Tools Required • Small flat blade screwdriver • Phillips screwdriver (#1) • Adjustable wrench • Wire cutter/stripper/crimper tool 4.2 Cable Requirements Video Transmission (Coaxial) Cable Type: RG-59/U fo ...