CUBETAPE C190POS Quick Start Manual

LED OFF: Battery 40% - 100%. LED Slow Flash: Battery 20% - 40%. LED Medium Flash: Battery 10% - 20%. LED Fast Flash: Battery below 10% - recharge immediately. USB Cable PC Cradle Charging: To charge battery place the device in the cradle. Battery is charging when the charge LED is RED. Battery is fully charged when the charge LED is off. C190POS Quickstart Guide V ERSION 1.0.1 Register your device at www.cubetape.com/register 1. Power ON: Hold down ‘m’ button for 2 seconds. Power OFF: Hold down ‘m’ button for 5 seconds. 3. Connect Cubetape to Cradle: Scan Cradle Pairing Barcode to pair. Blue LED solid when connected. 2. Cradle Install on PC: LED on cradle confirms power connection. C190POS is a precision measuring instrument and barcode scanner with a wide range of configurable options including measurement units, precision and data formatting and will connect to most platforms including Windows Android and iOS. Cubetape scanner dimensioners have factory defaults set for common terminal, communication and measurement requirements. Settings can be changed by scanning the barcodes in this guide with further options available at www.cubetape.com/downloads ‘m’ Button Battery Tape Cassette Push in the direction of the arrow CHARGE BLUETOOTH Cradle Pairing Barcode Measuring Techniques: 1. Hook the tape end over the far edge of the package. 2. Align the tape exit to the near edge. 3. Press the ‘m’ button to record and transmit the measurement. Battery and Tape Compartments: 1. Remove the silicone rubber sleeve. 2. Slide the back cover open and remove it. 3. Remove the tape cassette or battery. Battery/Power Management: For power management of USB devices when PC is in sleep mode: https://www.top-password.com/blog/ set-windows-to-power-on-off-usb- devices-in-sleep-mode/ 1 2 3 1 2 3 For full manual go to www.cubetape.com/downloads For support email [email protected] Some features in this guide are unsupported in product with SN prior 201xxxx. C190POS Quickstart Guide V ERSION 1.0.1 Register your device at www.cubetape.com/register Sleeve

Scan Bluetooth Direct Mode (HID) barcode. Open PC Settings/Add Bluetooth Device/Select Cubetape. When LED is solid BLUE, Cubetape is paired. Connect directly to Android Device (without cradle): Scan Bluetooth Direct Mode (HID) barcode. Open Android Device Settings/Add Bluetooth Device/Select Cubetape. When LED is solid BLUE, Cubetape is paired. Bluetooth Direct Mode (HID) C190POS User Shortcuts: Automate data input with shortcut barcodes. C190POS General Settings: Add/Append Default Factory Setting EURO Pallet 120 x 80 CHEP Pallet 117 x 117 UK Pallet 120 x 100 US Pallet 48 x 40 Bluetooth SPP Mode Bluetooth HID Mode Bluetooth Reset Resend Reverse Tare On Default Engine Setting Add/Append Default Factory Setting EURO Pallet 120 x 80 CHEP Pallet 117 x 117 UK Pallet 120 x 100 US Pallet 48 x 40 Bluetooth SPP Mode Bluetooth HID Mode Bluetooth Reset Resend Reverse Tare On Default Engine Setting Add/Append Default Factory Setting EURO Pallet 120 x 80 CHEP Pallet 117 x 117 UK Pallet 120 x 100 US Pallet 48 x 40 Bluetooth SPP Mode Bluetooth HID Mode Bluetooth Reset Resend Reverse Tare On Default Engine Setting Add/Append Default Factory Setting EURO Pallet 120 x 80 CHEP Pallet 117 x 117 Bluetooth SPP Mode Bluetooth HID Mode Default Engine Setting Add/Append Default Factory Setting UK Pallet 120 x 100 US Pallet 48 x 40 Bluetooth SPP Mode Bluetooth HID Mode Bluetooth Reset Resend Reverse Tare On Default Engine Setting UK Pallet 120 x 100 US Pallet 48 x 40 Bluetooth SPP Mode Bluetooth HID Mode Bluetooth Reset Resend Add/Append Default Factory Setting CHEP Pallet 117 x 117 UK Pallet 120 x 100 US Pallet 48 x 40 Bluetooth SPP Mode Bluetooth HID Mode Bluetooth Reset Resend Reverse Tare On Default Engine Setting Add/Append Default Factory Setting EURO Pallet 120 x 80 CHEP Pallet 117 x 117 Bluetooth SPP Mode Bluetooth HID Mode Default Engine Setting Add/Append Default Factory Setting EURO Pallet 120 x 80 CHEP Pallet 117 x 117 Bluetooth SPP Mode Bluetooth HID Mode Bluetooth Reset Default Engine Setting Suffix = CRLF Suffix = CR Suffix = TAB Factory default settings are: Dip switches beneath cradle: 1 2 3 4 ON 1 2 3 4 ON Setting Factory Default Bluetooth Cradle Pairing Mode Keyboard English Send Option 1DIM Data Format TAB Source Prefix OFF Units inches Precision nearest whole Reverse Tare Value 112 About C190POS Quickstart Guide V ERSION 1.0.1 Register your device at www.cubetape.com/register For full manual go to www.cubetape.com/downloads For support email [email protected] Some features in this guide are unsupported in product with SN prior 201xxxx.