Haws 3602 Assembly Instruction Manual

Page 1 of 12 1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424 E-mail: [email protected]  website: www.hawsco.com No. 0580001169 (1) MODELS 3602 & 3602FR Outdoor Drinking Fountain INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS LIMITED WARRANTY HAWS warrants that this specific product is guaranteed against defective material or poor workmanship for a period of one year from date of shipment. HAWS liability under this warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods, or part thereof, which shall appear to the Company upon inspection to be of defective material or not of first class workmanship, provided that claim is made in writing to Haws within a reasonable period after receipt of the product. Where claims for defects are made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or for any expense connected therewith made by the owner or his agents, except upon written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective materials or poor workmanship, except for replacements, as provided above. Buyer agrees that HAWS shall not be liable for general, special, or consequential damages claimed to arise under the contract of sale. The drinking fountain manufactured by HAWS is warranted to function if installation and maintenance instructions provided are adhered to. The units also must be used for the purpose for which they were intended. NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED OR GIVEN BY HAWS. NOTE TO INSTALLER: Please leave this information with the Maintenance Department. SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS MODEL PLEASE CALL: TECHNICAL SUPPORT: 1-800-766-5612 FOR CUSTOMER SERVICE: 1-888-640-4297

Page 2 of 12 RECOMMENDED TOOLS: - Measuring Tape - PVC Pipe Cutter - Plastic Tubing Cutter - PVC Solvent Weld Glue - ¼” Bit-Holding Screwdriver - Level - 10” Pipe Wrench - Adjustable Plier - 1/8 and 5/32 Tamper Resistant Hex Bits (Supplied) - 9/16” and 5/8” Box/Open Combination Wrenches, 8” Max Length - 3/8” Socket Wrench/Rachet, 8” Max Length - 9/16” Deep Socket - 15/16” Socket LOCATION OF UNIT: The Model 3602/3602FR Bottle Filler / Fountain can be installed and assembled to be ADA accessible by first locating the pedestal base with at least 8 inches of clear unobstructed hardscape behind the pedestal. Provide hardscape that is at least 74 inches wide. When the right pedestal arm is installed in the high orientation, the height dimensions shown on the model specification sheet meet current Federal Americans with Disabilities Act (ADA) wheelchair requirements. When a fountain is installed on top of the pedestal, the height dimensions shown on the model specification sheet meet current ADA standing height requirements. When installing this unit, local, state and federal (including ADA) codes must be adhered to. If height other than shown is required, then dimensions must be adjusted accordingly. SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6 ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter is recommended. PLUMBING CONNECTIONS: Water supply inlet connection is a 3/8“O.D. compression fitting. Waste outlet is 1-1/2” PVC pipe. Plumbing connections vary depending on how the unit is configured during assembly. Please consult the installation drawings below for supply and waste fitting arrangements and assembly for your specific model. MAINTENANCE: For 3602 models- Periodically clean the pushbutton valve strainer. Refer to 5874 Series Valve Operation and Maintenance Sheet for more information. For 3602FR models- Refer to 6518 Operation and Maintenance Sheet for more information. INSTALLATION PROCEDURE Follow the installation procedures outlined in the installation diagrams for your specific model below. Note: 3602FR versions must be connected to Haws Model 6518 series freeze resistant bury valve(s), sold separately. See 6518 installation manual for instructions. GENERAL NOTES: 1. For all compression fitting connections, only connect NSF-61 copper or plastic 3/8” outside diameter tubing. The following assembly instructions must be followed to ensure a watertight connection: a. Cut tubing square and clean. Deburr if necessary. b. Place compression nut and ferrule over end of tubing. c. For plastic tubing (must be ¼” inside diameter), insert supplied tubing insert into end of tubing.

Page 3 of 12 d. Push tube into the fitting until it bottoms out. e. Thread nut onto fitting and tighten snugly with 5/8” wrenches. *For more information about Haws products, see our website: www.hawsco.com © 2021 Haws® Corporation – All Rights Reserved HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. Tube Sizes O.D. Tolerance Insertion Depth 3/8” ±.005” 3/4” TROUBLESHOOTING PROBLEM REPAIR CHECKLIST 1. Insufficient bubbler flow (From Drinking Fountain) 1a. Verify minimum 30 psi flowing supply pressure. b. For 3602- Check that inlet screwdriver stop valve is wide open. Clean inlet strainer or adjust valve to increase flow. See 5874 Series Valve Manual*. c. For 3602FR- Adjust valve to increase flow. See 6518FR Manual*. 2. Insufficient bottle filler flow 2a. b. c. Nozzle strainer is clogged. Use nozzle removal tool to remove strainer and replace. Replacement strainers may be ordered by calling Customer Service. For 3602- Check that inlet screwdriver stop valve is wide open. Clean inlet strainer or adjust valve to increase flow. See 5874 Series Valve Manual.* For 3602FR- Adjust valve to increase flow. See 6518FR Manual.*

WHEN ORDERING PARTS, PLEASE IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:2 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV PARTS BREAKDOWN DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT 0580001169 SHEET 1 OF 2 SPECIFY PART NUMBER WEBSITE: WWW.HAWSCO.COM DP ECN: E-MAIL: [email protected] 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 © 2021 Haws Corporation - All Rights Reserved. 3602 / 3602FR PARTS BREAKDOWN REPLACEMENT PARTS ALL MODELS MODEL PBA7 BUTTON ASSEMBLY (NON FR MODELS) MODEL VRK5874 VALVE REPAIR KIT (NON FR MODELS) 0006983506 SPANNER WRENCH (NON FR MODELS) 0510001030 HEX BIT, PINNED, 5/32" 0510001029 HEX BIT, PINNED, 1/8" OPTIONAL ACCESSORIES MODEL 3661 HOSE BIB (NOT FREEZE RESISTANT) MODEL 3660 LOCKABLE HOSE BIB (NOT FREEZE RESISTANT) PAGE 4 OF 12 3602 / 3602FR MODULAR OUTDOOR FOUNTAIN SYSTEM MODEL 5703M BUBBLER HEAD REPLACEMENT PARTS DRINKING FOUNTAIN MODEL 5874PB PUSHBUTTON (NON FR MODELS) MODEL 5881PBA BUTTON ASSEMBLY (FR MODELS) MODEL 3670 DOG BOWL (NOT FREEZE RESISTANT) MODEL MTG.3600 INSTALLATION AID

PARTS BREAKDOWN 3602 / 3602FR MODULAR OUTDOOR FOUNTAIN SYSTEM *FR (FREEZE RESISTANT) MODELS REQUIRE THE USE OF SEPARATE FREEZE RESISTANT VALVES (NOT SUPPLIED). SEE INSTALLATION DRAWINGS ON THE FOLLOWING PAGES FOR DETAILS. THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:16 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV PARTS BREAKDOWN DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM DP ECN: WHEN ORDERING PARTS, PLEASE SPECIFY PART NUMBER SHEET 2 OF 2 0580001169 © 2021 Haws Corporation - All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. PAGE 5 OF 12 3602 / 3602FR MODEL 3671 PEDESTAL ARM ASSEMBLY MODEL 3680 OR 3680FR* FOUNTAIN ASSEMBLY MODEL 3690 OR 3690FR* BOTTLE FILLER ASSEMBLY MODEL 3674 PEDESTAL ASSEMBLY

© 2021 Haws Corporation - All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. 3602 / 3602FR IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:24 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV INSTALLATION DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT 0580001169.D SHEET 1 OF 7 ECN: WEBSITE: WWW.HAWSCO.COM DP 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] PAGE 6 OF 12 NOTES: 1. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE ADHERED TO. INSTALL A TRAP IN THE WASTE LINE AND A SCREWDRIVER STOP IN THE SUPPLY LINE IF REQUIRED. ADA WHEELCHAIR ACCESSIBLE HEIGHT PERSON'S HEIGHT ADA STANDING CONCRETE ANCHORS INCLUDED. RE-USABLE TEMPLATE MODEL MTG.3600 AVAILABLE, SOLD SEPARATELY. 34 3/4" 882mm 787mm 31" 406mm 16" 687mm 27" 41 1/2" 1053mm 21" 533mm 10" 254mm 10" 254mm 254mm 10" 10" 254mm 2X 21" 533mm FRONT ACCESS PANEL FULL HEIGHT BOTH SIDES SIDE PANEL LOWER ACCESS HAWS MODEL 3602 OR MODEL 3602FR IS FULLY COMPLIANT WITH THE FEDERAL 2010 AMERICANS WITH DISABILITIES ACT (ADA) ACCESSIBILITY REQUIREMENTS WHEN INSTALLED AS SHOWN HERE AND WHEN INSTALLED WITH PROPER CLEARANCES AND ACCESS. LOCATE THE PEDESTAL BASE WITH AT LEAST 8" OF CLEAR UNOBSTRUCTED HARDSCAPE BEHIND THE PEDESTAL. IT IS THE RESPONSIBILITY OF THE INSTALLER TO ADHERE TO LOCAL, STATE,AND FEDERAL CODES WHEN INSTALLING THIS UNIT. DISTANCE TO SURROUNDING OBJECTS, APPROACH SURFACES, ETC. SHOULD BE CONSIDERED.

WITHIN THIS AREA FRONT FACE 4X 5/8" BOLTS AND WASHERS (SUPPLIED) 4X CAST-IN ANCHORS (SUPPLIED). SET AT 7" SQUARE SPACING AND ORIENT AS SHOWN © 2021 Haws Corporation - All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:24 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV INSTALLATION DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM DP ECN: SHEET 2 OF 7 0580001169.D 3602 / 3602FR PAGE 7 OF 12 PAGE 7 OF 12 INSTALLATION INSTRUCTIONS STEP 1 MOUNT PEDESTAL TO CONCRETE SLAB IN DESIRED ORIENTATION. SLAB TO BE 30" MINIMUM SQUARE AND 6" MINIMUM THICK (BY OTHERS). PLUMBING CAST IN CONCRETE MUST FIT IN 7" DIAMETER AREA CENTERED UNDER PEDESTAL LOCATION. FOR 3602FR MODEL, SEE REQUIRED BURY VALVE (NOT SUPPLIED) INSTALLATION REQUIREMENTS ON SHEET 6. MODEL MTG.3600 (OPTIONAL) TEMPLATE FOR SPACING ANCHORS DURING CONCRETE POUR STEP 2 REMOVE BOTTOM COVER PLATES FROM ARMS BY REMOVING 3 1/4" BUTTON HEAD SCREWS. INSTALL ONE FOUNTAIN ARM ON RIGHT SIDE AS SHOWN. USE 1/4" FLAT HEAD SCREWS (SUPPLIED) TO INSTALL PLATE. USE 3/8" BOLTS AND NUTS (SUPPLIED) AND TORQUE TO 18 FT-LBS TO INSTALL ARM. E E SECTION E-E 4X 5/8" BOLTS AND WASHERS SUPPLIED WITH ANCHORS 7" 178mm 7" 178mm 4X 7/8" 21mm MOUNTING HOLES 4X 1/4" FLAT HEAD SCREWS PLATE, ORIENT AS SHOWN 4X 3/8" NUTS 4X 3/8" BOLTS FOUNTAIN ARM

PLACE ONE FOUNTAIN ASSY. ON TOP OF TRIM RING, FACING THE FRONT. USE 3/8" BOLTS AND NUTS VIA THE FRONT ACCESS PANEL TO SECURE FOUNTAIN ASSY. TO PEDESTAL. PLACE TRIM RING AND INSTALL 2ND FOUNTAIN ASSY. ON ARM AS SHOWN. CAREFULLY CENTER TRIM RINGS AND TORQUE BOLTS AND NUTS TO 18 FT-LBS © 2021 Haws Corporation - All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:24 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV INSTALLATION DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM DP ECN: SHEET 3 OF 7 0580001169.D 3602 / 3602FR PAGE 8 OF 12 PAGE 8 OF 12 FOUNTAIN ASSEMBLY (FOUNTAINS INTERCHANGEABLE) 4X 3/8" BOLTS AND NUTS, INSTALL VIA FRONT ACCESS PANEL TRIM RING FRONT FACE FOUNTAIN ASSEMBLY (FOUNTAINS INTERCHANGEABLE) 4X 3/8" BOLTS & NUTS, INSTALL FROM UNDERSIDE TRIM RING

WASHERS ADAPT FROM 1-1/4" TO 1-1/2" AT EACH DRAIN TAIL PIECE. BLACK COMPRESSION WASHERS ARE USED IN TRAP ADAPTERS AT TEE. USE APPROPRIATE PVC CEMENT TO MAKE SOLVENT CEMENT CONNECTIONS. TRIM WASTE BEND AND/OR TAIL PIECE LENGTH IF REQUIRED. NOTE THAT EXTRA PARTS MAY BE INCLUDED TO FACILITATE OTHER CONFIGURATIONS OF THIS FOUNTAIN. INSTALLATION INSTRUCTIONS © 2021 Haws Corporation - All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:24 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV INSTALLATION DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM DP ECN: SHEET 4 OF 7 0580001169.D 3602 / 3602FR PAGE 9 OF 12 PAGE 9 OF 12 WASTE BEND 2X COMPRESSION NUT AND RED COMPRESSION WASHER 2X COMPRESSION NUT AND BLACK COMPRESSION WASHER PVC TRAP ADAPTER IS GLUED INTO PVC TEE 1-1/2" PVC TEE 1-1/2" PVC DRAIN PIPE WASTE LINE INSTALLED PER LOCAL CODES AND STANDARDS 8" TAIL PIECE

3602FR SUPPLY PLUMBING* FROM BURY VALVES (NOT SUPPLIED) TO NOZZLE TO NOZZLE STEP 5 COMPLETE WATER SUPPLY PLUMBING AS SHOWN. OPEN SUPPLY VALVE(S) AND TEST. REPLACE ARM BOTTOM PLATES AND PEDESTAL ACCESS PLATES. BURY VALVES (NOT SUPPLIED) ARE REQUIRED FOR 3602FR INSTALLATION. REFER TO BURY VALVE OPERATION AND MAINTENANCE MANUAL FOR ADDITIONAL INFORMATION. * SEE NEXT SHEET OF THIS DRAWING FOR MORE INFORMATION ON INSTALLING BURY VALVES WITH THIS MODEL. INSTALLATION INSTRUCTIONS © 2021 Haws Corporation - All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:24 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV INSTALLATION DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM DP ECN: SHEET 5 OF 7 0580001169.D 3602 / 3602FR PAGE 10 OF 12 PAGE 10 OF 12 NPT TO COMPRESSION ADAPTER (SUPPLIED) COMPRESSION TEE WITH MALE NPT (SUPPLIED) 3/8" TUBING (SUPPLIED) INSERTS, FERRULES, AND COMPRESSION NUTS (SUPPLIED) DRAIN PIPING NOT SHOWN FOR CLARITY TUBING INSULATION (SUPPLIED) OVER 3/8" TUBING (SUPPLIED) 2X COMPRESSION STRAIGHT CONNECTORS WITH INSERTS, FERRULES, AND NUTS (SUPPLIED) PNEUMATIC TUBING FOR BURY VALVE ACTUATION (NOT SUPPLIED)

WITH MANUFACTURER'S INSTRUCTIONS. INSTALLATION MUST COMPLY WITH LOCAL CODES / STANDARDS, INCLUDING ADA CODES IF APPLICABLE. VALVE BOX (BY OTHERS) NOTE LOCATION SHOWN FOR DRAWING CONVENIENCE, DO NOT LOCATE BOXES UNDER FOUNTAINS OR WITHIN ADA CLEARANCE REQUIREMENTS. 3602FR GENERAL BURY VALVE LAYOUT (FOR REFERENCE ONLY) CONNECT TO WATER SUPPLY MODEL 6518FR.2 DUAL BURY VALVE REQUIRED (SOLD SEPARATELY) WASTE LINE INSTALLED PER LOCAL CODES / STANDARDS CONCRETE PAD (BY OTHERS) MODEL 3602FR 7" 178 MAX © 2021 Haws Corporation - All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:24 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV INSTALLATION DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM DP ECN: SHEET 6 OF 7 0580001169.D 3602 / 3602FR PAGE 11 OF 12 PAGE 11 OF 12

FOUNTAINS CAN BE INSTALLED TO FACE ANY DIRECTION ADA ARM HEIGHT POSITION OPTIONS LEFT SIDE* RIGHT SIDE* ARM HEIGHT (LOWER EDGE) BUBBLER NOZZLE HEIGHT STANDING ADA YES (STD) NO 31-7/8 [809 mm] 39-3/8 [999 mm]** WHEELCHAIR ADA YES YES (STD) 27 [687 mm] 34-5/8 [878 mm] CHILD ADA YES YES 22-1/4 [566 mm] 29-7/8 [757 mm] * RIGHT AND LEFT CAN BE REVERSED IF PEDESTAL IS ROTATED 180 . **NOZZLE HEIGHT IS 41-1/2" WHEN FOUNTAIN IS INSTALLED ON TOP OF PEDESTAL. NOTES ON OPTIONAL CONFIGURATIONS HAWS 3600 SERIES OUTDOOR FOUNTAINS ARE MODULAR AND CAN BE ASSEMBLED AND CONFIGURED MANY DIFFERENT WAYS. DISPLAYED HERE ARE A FEW EXAMPLES. CONFIGURATIONS OTHER THAN THAT SHOWN IN THE INSTALLATION INSTRUCTIONS FOR THE 3602 / 3602FR MAY AFFECT COMPLIANCE WITH ADA REGULATIONS. IT IS THE RESPONSIBILITY OF THE INSTALLER TO UNDERSTAND LOCAL, STATE, AND FEDERAL REGULATIONS AS APPLICABLE IF INSTALLING THIS FOUNTAIN IN CONFIGURATIONS OTHER THAN THAT INDICATED ON SHEET 1 (PAGE 6 OF 12). ADA ARM HEIGHT POSITION OPTIONS LEFT SIDE* RIGHT SIDE* ARM HEIGHT (LOWER EDGE) BUBBLER NOZZLE HEIGHT STANDING ADA YES (STD) NO 31-7/8 [809 mm] 39-3/8 [999 mm]** WHEELCHAIR ADA YES YES (STD) 27 [687 mm] 34-5/8 [878 mm] CHILD ADA YES YES 22-1/4 [566 mm] 29-7/8 [757 mm] * RIGHT AND LEFT CAN BE REVERSED IF PEDESTAL IS ROTATED 180 . **NOZZLE HEIGHT IS 41-1/2" WHEN FOUNTAIN IS INSTALLED ON TOP OF PEDESTAL. © 2021 Haws Corporation - All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation. THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE. APPROVED: DRAWN: PART NUMBER SCALE: REVISION DHP 6/11/20 1 1:24 FV 03/18/21 DRAWING TYPE: SIZE: A 5652 BY: FV INSTALLATION DATE: DATE: REV. ECN: 5652 CHK'D.: MODEL(S) 1455 KLEPPE LANE SPARKS, NEVADA 89431 (775) 359-4712 FAX (775) 359-7424 E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM DP ECN: SHEET 7 OF 7 0580001169.D 3602 / 3602FR PAGE 12 OF 12 PAGE 12 OF 12 BOTTLE FILLER CAN BE INSTALLED ON ARMS ADA STANDING HEIGHT FOUNTAIN INSTALLED ON PEDESTAL 27" 687mm WHEELCHAIR ADA POSITION 22 1/4" 564mm CHILD ADA POSITION