Fortin E400 Quick Installation Manual

REMOTE STARTER & ALARM PROGRAMMING REMOTE TRANSMITTER(S) WIRING / CONNECTION GUIDE The system can learn up to a maxi- mum of 4 transmitters. Any transmitters can be stored in more than 1 memory slot. When a 5th transmitter is learned the 1st remote is erased (FIFO). Red Black White Black Blue Blue Programming LED (4-pin) Antenna (4-pin) RS-232 Data-Link (2pin) Valet/Programming Button Shock Sensor (3-pin) (4-pin) Antenna White#14 Brown #18 Red #14 Red #14 Red #22 Power Power (utility) Power Parklights Ign/Acc/Start Tachometer Foot-Brake Door Pin Pos Trunk/Hatch (open) Lock Starter Parklight (-) while running Purple White Orange White/Black Dk. Blue White/Red Yellow/Red Yellow/Black Brown/White Lt. Green Lt. Green/Black 24 8 Ignition Starter Ignition Switch Aux.1 Aux.2 INPUT OUTPUT Arm ~ Cut loop for automatic transmission mode. External LED (2-pin) Yellow #14 Orange #14 Pink #14 Black #18 Starter Accessory Ignition Ground Hood Pin E-Brake Door Pin Neg. Trunk/Hatch Pin Starter Kill Unlock Disarm Ignition Accessory Horn Siren Aux.IN Grey Brown Dk. Green Pink Yellow White/Green Yellow/Green Pink/Black Orange/Black Red/Black Red Purple/White 1 1 To Vehicle To Vehicle Starter-Kill / Anti-Grind Relay See programming guide, Function #10 Neutral Safety Switch for manual transmission vehicle Optional Relay Not Use Lt.Blue QUICK INSTALLATION GUIDE RF25BV/RF252W COPYRIGHT © 2015-2016, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED MADE IN CANADA REV.:20161011 WIRING / CONNECTION GUIDE PROGRAMMING REMOTE TRANSMITTER(S) The system can learn up to a maxi- mum of 4 transmitters. Any transmitters can be stored in more than 1 memory slot. When a 5th transmitter is learned the 1st remote is erased (FIFO). STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 X1 X1 X1 Turn the Ignition ON. Press and hold the valet switch until the Parking lights turn ON, the horn/ siren will chirp. Press and release the valet-switch once. The parking lights will fl ash to confi rm. Press and re- lease the brake pedal once. On each Transmitter press the LOCK button once (maximum 4 transmitters), the parking lights will fl ash to confi rm. Press and release the brake-pedal once. Turn the Ignition OFF to exit programming. 1 3 2 4 ONE ONE E400 ONE GUIDE # 32501

Program Driver 2 Multivehicle program — — — 2 Programmable Output (+) Ign/Acc/Start/ Park-Light 2nd Ignition 2nd Accessory 2nd Starter Pink Ignition Pink Ignition Pink Ignition Orange 2nd Ignition Orange Accessory Orange Accessory White Starter White 2nd Ignition White Starter Yellow 2nd Starter Yellow Starter Yellow 2nd Starter Brown Park-Light (+) Brown 2nd Accessory Brown 2nd Ignition Aux. 1 Park-Light (-) Aux. 1 Park-Light (-) 3 Tachless sensivity Increase crank time (By default) Decrease crank time 4 Remote car starter runtime Gas: 15 minutes Diesel: 30 minutes Gas: 7 minutes Diesel: 14 minutes Gas: 3 minutes Diesel: 6 minutes — — — 5 — — — — — — — 6 Lock/Unlock control No Unlock before remote- start & Lock after remote-start. Lock after remote-start. Unlock and relock after shut-down. Relock 10 sec.after shut-down. Disarm before shut down. 7 Ignition Lock/Unlock control No Lock after foot-brake & unlock after key is turned off. Unlock after key is turned off. Doorlock Output at Ignition only. — — 8 Unlock Pulse Time Single 0.25 sec Double 0.25 sec Single 4.0 sec Single 2.5 sec Single 1.5 sec Single 0.75 sec 9 Active or Passive Alarm & Starter Kill Active Press LOCK to activate the Alarm and starter- kill. Passive (Lock disabled) Arm alarm activate starter-kill 30(MODE 4), 60(MODE5), or 120(MODE6) sec. after the door is closed. Passive (Lock enabled) Arm alarm, activate starter-kill and lock doors 30(MODE 4), 60(MODE5), or 120(MODE6) sec. after the door is closed. Passive arm 30 seconds (by default if MODE 2 ot 3 is activated. Passive arm 60 seconds. (if MODE 2 ot 3 is activated. Passive arm 120 seconds. (if MODE 2 ot 3 is activated. 10 Starter Kill Output Starter-kill &anti-grind Anti-grind only Relay normally open — — — 11 Sound confi rmation & LED antenne 1st LOCK/UNLOCK silent - 2nd LOCK/ UNLOCK sound --------------------------- Antenna LED active. LOCK/UNLOCK sound always. Antenna LED disabled. Antenna LED disabled with ignition. Confi rmation sound at LOCK only Panic mode disabled 12 Horn/Siren confi rmation Horn(-) only. Siren(+) only Siren(+) & Horn(-) During alarm siren(+) will pulse and horn(-) is constant. — — 13 Confi rmation Pulse Long Short — — — — 14 Alarm ON/Off Starter ON/Off Alarm OFF Remote-starter ON Alarm ON Remote-starter ON Alarm ON Remote-starter OFF — — — FUNCTION MASTER RESET OF ALL PROGRAMMED FUNCTIONS AND REMOTES STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 Disarm alarm, disable valet. Turn the Igni- tion ON. Press and hold the valet switch until the Parking lights turn ON, the horn/siren will chirp. Press and release the valet switch 23 times. X1 Press and release the brake- pedal once. Press and hold the valet switch for 5 seconds. The Parking lights will flash to confirm. Turn the Ignition OFF to exit programming. The Parking lights will flash 4 times. STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 X1 MODE 1 - LOCK MODE 2 - UNLOCK MODE 3 - TRUNK MODE 4 - START MODE 5 - LOCK + UNLOCK MODE 6 - TRUNK + START Disarm alarm, disable valet. Turn the Igni- tion ON. Press and hold the valet switch until the Parking lights turn ON, the horn/siren will chirp. Press and release the valet switch X times for the desired function. The Park- ing lights will flash and the horn/siren will chirp each time to confirm. Press and release the brake-pedal once. Turn the Igni- tion OFF to exit programming. The Parking lights will flash 4 times. Press the BUTTON on a programmed remote to select the mode (X). The Parking lights will flash 1-6 times to confirm. Return to step 3 to programmed the next option FUNCTION PROGRAMMING

Disable (Unlock signal) Automatically LO CK and rearm alarm if door(s) are not opened after 30 seconds. Automatic Lock when starter kill arms. Lock pulse only when its Unlock — — 16 Cold Start Timer 3 hours at -5oc/Runtime 1.5 hours at -5oc/ Runtime 3 hours at -5oc/5 minutes 1.5 hours at -5oc/5 minutes Cold time OFF — 17 Domelight Delay Disable Enable Ignore door trigger (dome light) when arming or Remote-starting — — — — 18 Diesel Mode Disable Enable (20 seconds) Delay between Ignition power up and Starter (crank). Enable (10 seconds) Delay between Ignition power up and Starter (crank). Enable No delay between Ignition power up and Starter (crank). — — 19 Turbo timer Disable Run 2 minutes. Run 4 minutes. — — — 20 Engine supervision: -Tachless - -analog tach- -Tach Data- Link- Tachless on crank and supervision Tach Data- Link or analogic after Tachless only. ( vehicles with automatic transmission only) Analog Tach learning (see p.4 for programming) Start (crank) 8 sec on tachless. ( vehicles with automatic transmission only) Start (crank) 8 sec+ Supervision by Data-Link Tach (Data interface required) Tach Data-Link only (Data interface required) 21 Start Attempts 2 1 3 — — — 22 TRANSMITTER START/STOP FUNCTION Start: (button 4) 1 sec. Stop: (AUX --> button 4) 1 sec. Start : (button 4) 3 sec. Stop : (AUX --> button 4) 1 sec. 1-way remote only Option alarm active 2-way remote Battery saver Start:(AUX --> button4) 1sec. Stop : (button 4) 1 sec.1-way remote only — — 23 Master RESET RESET all programming options by default. (Retains already programmed remote.) — — — — — 24 Special application Disable Application 1 Application 2 Application 3 — — 25 Auxiliary 1 Output AUX--> LOCK 0.5 seconds & disarm alarm 0.5 seconds 10 sec latch or until a button is pressed. 20 sec latch or until a button is pressed. 30 sec latch or until a button is pressed. Latch until shutdown 26 Hybrid mode Gas / Diesel vehicle Hybrid vehicle — — — — 27 Auxiliary 2 Out- putAUX--> UNLOCK 0.5 seconds & disarm alarm 0.5 seconds 10 sec latch or until a button is pressed. 20 sec latch or until a button is pressed. — 28 Manual transmission Neutral safety switch Special Application No application Enable (see p.4) For manual transmission vehicles equipped with neutral safety switch. DO NOT CUT THE LOOP. Connect the auxiliary IN (Purple/White) to the neutral safety switch of the vehicle. 29 Alarm Duration 30 seconds 60 seconds 120 seconds — — — 30 Valet code Ignition ON Valet button x3 times. Ignition ON Valet button x3 times and x1 times 3 seconds. Ignition ON Valet button x4 times and x1 times 3 seconds. Ignition ON Valet button x5 times and x1 times 3 seconds. Ignition ON Valet button x6 times and x1 times 3 seconds. Ignition ON Valet button x7 times and x1 times 3 sec. 31 Special application Programmable output (+) No special application Priority on function 2 Special application - Function 2 (all option) not available. — — Enable at ground out, disable with vehicle ignition off White wire (5th relays): Trunk output(+) White wire (5th relays): (+)Parking light output 32 Configuration Dk.Blue (Pin17) Yellow/Red (Pin19) wire Dk.Blue (Ground out, Pin17): Shut-down 1 second after remote start run time. ------------------ Yellow/Red (Pin19)=Arm Dk.Blue (Ground out, Pin17): Shut-down 3 seconds after remote start run time. Yellow/Red (Pin19) (Arm): Shutdown after — — — 33 Manual transmission function Activated by the remote starter remote. See page 4. Automatically activated by hand-brake and Foot Brake. Manual sequence completed by locking the doors Cancel ready mode when trunk open. — — 34 Trunk output Pulse 0.5 seconds Pulse 2.5 seconds Unlock before trunk pulse 0.5sec Trunk Output at ignition only — — 35 Door unlock Special application No special application Activate vehicle ignition at unlock. Activate vehicle ignition and accessory at unlock. — — — 36 Activation/ desactivation remote Valet Mode by remote : LOCK + UNLOCK or Valet button. by remote : AUX --> Lock + Unlock or valet button. By Valet button only — — — 37 Security Remote car starter Special application No special application Security ON: Shutdown Engine if the door is opened before UNLOCK is pressed. (Door trigger required). — — — — 38 System control by OEM Remote Disable Enable (Press 3x Lock to remote start) (Bypass module required) — Enable Alarm controled by OEM Remote. Enable (Press Lock, Unlock Lock to remote start) (Bypass module required) — 39 AUX1 CONTROLED BY Temperature Disable Enable : AUX1 activated at +5oc when remote started (see function 25) — — — — LEGEND: FUNCTION BY DEFAULT

COLD START MODE REMOTE START / ALARM DIAGNOSTICS Insert the key and turn it to the ignition (RUN/ON) position. Within 10 seconds press and release the Valet switch 3 times. The LED will turn ON solid and remain ON. STANDARD • Open any door(s) • Open the hood • Disengage the parking brake WITH NEUTRAL SAFETY SWITCH • Transmission not in neutral position • Open the hood • Disengage the parking brake Note : If the parking lights flash 3 times when Remote-Starting, Ready Mode is not enabled. READY MODE REMOTE STARTER Parking Light flashes (before starting) : 3x Ready Mode disabled 4x Valet Mode activated (The LED is on) 5x Hood open Parking Light flashes (after starting) : 1x Normal stop (Brake, Park Brake) 3x Runtime expired or shut down by Transmitter 4x No tachometer signal 5x Hood open 6x Over crank threshold (8 sec- onds) ALARM DIAGNOSTICS Parking Light flashes (after disarm) : 3x Door open – zone 3 4x Shock sensor – zone 4 5x Hood open – zone 5 6x Trunk open – zone 6 7x Auxiliary IN– zone 7 8x Tilt Sensor – zone 8 X INDICATES THE NUMBER OF TIMES THE PARKING LIGHTS WILL FLASH AVERTISSEMENT The engine’s tachometer signal must be detected by the remote starter to operate in a manual transmission. Tachometer is connected directly to the vehicle: Option 20: Mode 1 or 3 - or - Tachometer is obtained Through the interface module EVO-ALL or EVO- CHR:Option 20: Mode 1 or 6 Make sure that all doors are closed and the transmission is in the NEUTRAL position. While the engine is running. Engage the parking brake. Release the brake pedal. NOTE If the parking lights flash 3 timed: Verify the Tachometer signal. Remove the key from the ignition barrel. The vehicle will remain running with the Remote-Starter. Exit the vehicle and close all of the doors.The Remote-Starter will stop running once all the doors are closed. ANALOG TACH LEARNING (PURPLE WIRE) READY MODE FOR NEUTRAL SAFETY SWITCH WARNING MULTI- LINK PROGRAM REMOTE-STARTER OPTIONS WITH ONE CLICK The MULTI-LINK displays diagnostic information and changes the remote- starters programming options. IGN START OFF READY MODE FOR NEUTRAL SAFETY SWITCH 1 Make sure that the transmission is in the NEUTRAL position. 3 Engage the parking brake. 2 MULTI-LINK Remove the key from the ignition barrel.The vehicle is ready to start. (and not running) NOTE: This feature will be functional only if the Tach is detected by a bypass module or connected directly to the vehicle. ENTER/EXIT VALET MODE Press and release 20 times the valet-switch. The park-lights will flash and the horn/siren will chirp once to confirm. X20 A long chirp indicates tach learning failed. If the procedure fails or to re-learn the tach setting, re-start the procedure. MULTI- LINK PROGRAM REMOTE-STARTER OPTIONS WITH ONE CLICK The MULTI-LINK displays diagnostic information and changes the remote- starters programming options. IGN START OFF 4 Press and release the brake-pedal once. 5 READY MODE FOR NEUTRAL SAFETY SWITCH START Start the engine with the key. 1 2 3 TACH LEARNING 1 Make sure that the transmission is in the NEUTRAL position. 3 Press and hold the valet-switch until the LED flashes, then release. Engage the parking brake. 2 MULTI-LINK Remove the key from the ignition barrel.The vehicle is ready to start. (and not running) NOTE: This feature will be functional only if the Tach is detected by a bypass module or connected directly to the vehicle. Press and release 20 times the valet-switch. The park-lights will flash and the horn/siren will chirp once to confirm. X20 A long chirp indicates tach learning failed. If the procedure fails or to re-learn the tach setting, re-start the procedure. MULTI- LINK PROGRAM REMOTE-STARTER OPTIONS WITH ONE CLICK The MULTI-LINK displays diagnostic information and changes the remote- starters programming options. IGN START OFF 4 Press and release the brake-pedal once. 5 READY MODE FOR NEUTRAL SAFETY SWITCH START Start the engine with the key. 1 2 3 TACH LEARNING 1 Make sure that the transmission is in the NEUTRAL position. 3 Press and hold the valet-switch until the LED flashes, then release. Engage the parking brake. 2 MULTI-LINK Remove the key from the ignition barrel.The vehicle is ready to start. (and not running) NOTE: This feature will be functional only if the Tach is detected by a bypass module or connected directly to the vehicle. Press and hold the valet switch until the Parking lights turn ON, the horn/siren will chirp. Push the VALISE button. The Parking lights will flash once and then remain on. Push the START button. The Parking lights will flash once and then remain on. + Press simultaneously UNLOCK and START buttons for 1 second until the parking lights flash once. TO DISABLE • Press simultaneously UNLOCK and START buttons for 1 second until the parking lights flash twice. • Put the Remote-Starter/alarm into Valet • Remote-Start the vehicle • Open the hood • Press the brake pedal • Turn the key to the ignition position. • Disable Ready Mode (manual transmission). NE The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, including either damage to the vehicle itself or to the remote-starter module. This module must be installed by a certified technician including all of the supplied safety devices. Please note that this guide has been written for trained professional technicians, a certain level of skills and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work. By default this system is setup for vehicles with a manual transmission. For vehicles with an automatic transmission the safety wire loop on the main unit must be cut. Before proceeding to the installation, make sure that the vehicle does not attempt to start when the when the vehicle is in the “drive” or “reverse” position. If an automatic transmission vehicle starts when the transmission is in gear, ensure that the safety wire loop on the unit is not cut. Once the safety wire loop is cut, the system is considered an automatic transmission remote-starter indefinitely. Once a loop is cut all warranties, guaranties, and liability is immediately void if the unit is install on a manual transmission vehicle.Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be install by qualified technician. This instruction guide may change without notice. To download the installation guide, user guide, or the latest quick installation guide, visit: www.fortin.ca Technical support: TEL: 514-255-4357 1-877-336-7797

POUR TRANSMISSION AUTOMATIQUE ET MANUELLE GUIDE D’INSTALLATION RAPIDE RF25BV/RF252W FILAGE / GUIDE DE BRANCHEMENTS PROGRAMMATION DES TÉLÉCOMMANDES Le système peut apprendre jusqu’à 4 télécommandes. Une seule télécommande peut prendre les 4 emplacements (programmée 4 fois). La 5e télécommande programmée supprime la première. (2 pin) Valet/Button de programmation ENTRÉE SORTIE Blanc #14 Brun #18 Rouge #14 Rouge #14 Rouge #22 Batterie Batterie (utilitaire) Batterie Feux de stationnement Ign/Acc/Start Tachymètre (AC) Pédale de frein Contact porte Pos. Valise/Hayon arrière (open) Verrouiller Armer Démarreur Feux de stationnement Masse d'activation Violet Blanc Orange Blanc/Noir Bleu foncé Blanc/Rouge Jaune/Rouge Jaune/Noir Brun/Blanc Vert pâle Vert pâle/Noir 24 8 Ignition Démarreur Barillet de contact DEL de programmation (4 pin) Antenne Détecteur de choc (3 pin) Aux 1. Aux 2. ~ Red Black White Black Blue Blue (4-pin) RS-232 Data-Link Coupez la boucle pour le mode transmission automatique. DEL extérieur (4 pin) Antenne Jaune #14 Orange #14 Rose #14 Noir #18 Démarreur Accessoires Ignition Masse Contact capot Frein à main Contact Porte Neg Contact Valise Antidémarreur Déverouiller Désarmer Ignition Accessoires Klaxon Sirène Aux. IN. Gris Brun Vert foncé Rose Jaune Blanc/Vert Jaune/Vert Rose/Noir Orange/Noir Rouge/Noir Rouge Violet/Blanc 1 1 Vers le véhicule Vers le véhicule Relais Anti-démarreur/Anti-grincement Voir guide de programmation, fonction #10 Relais optionnel 87 86 87a 85 30 Neutral Safety Switch pour véhicule à transmission manuel Non Utilisé Bleu pâle FILAGE / GUIDE DE BRANCHEMENTS PROGRAMMATION DES TÉLÉCOMMANDES COPYRIGHT © 2015-2016 FORTIN AUTO RADIO INC TOUS DROITS RÉSERVÉS FABRIQUÉ AU CANADA REV.:20161011 1 3 2 4 ÉTAPE 1 ÉTAPE 2 ÉTAPE 3 ÉTAPE 4 ÉTAPE 5 ÉTAPE 6 ÉTAPE 7 X1 X1 X1 Tournez l’ingnition à ON Appuyez et tenez enfoncé le bouton valet jusqu’à ce que les feux de positionnement s’allument et que le klaxon/ sirène retentisse, puis relâchez. Appuyez et relâchez le bouton valet une fois. Les feux de posi- tionnement clignoteront pour confirmer. Appuyez et relâchez une fois la pédale de frein. Appuyez sur le bouton de verrouillage de chacune des télécommandes (max 4), les feux de positionnement clignoteront pour confirmer chacune des programmations. Appuyez et relâchez la pédale de frein. Tournez l’ignition à OFF. ONE ONE E400 GUIDE # 32501