SUNPRO DD2700H Instructions

seconds. If there is no input within 6 seconds, the remote will exit the current setting procedure 2. The motor will jog and beep as a hint. Continue programming after the hint. UPPER LIMIT Move the screen up to the desired upper limit LOWER LIMIT Move the screen down to the desired lower limit Adjust Upper Limit Adjusting Lower Limit Motorized Screen Remote Instructions DD2700H Remote – Single Channel DD2702H Remote - 15 Channel 1 Pairing IMPORTANT READ ME FIRST Apply power to motor (1 jog and long beep once), within 7s, press STOP for 2s (2 jogs and 3 beeps), the motor has been paired successfully 2 Switching Rotating Direction (Optional) If the UP button is pressed, but the screen goes down, you will need to complete this step Press and hold the UP and DOWN buttons simultaneously for 2s, motor will jog once and rotation will be switched successfully *The motor needs to be in the reversing operation without limits 3 Setting Upper and Lower Limits Press and hold UP + STOP simultaneously for 2s (2 jogs, 3 beeps) upper limit is set Press and hold DOWN + STOP simultaneously for 2s (2 jogs, 3 beeps) Lower limit is set 4 Adjusting Limits Press and hold UP + STOP simultaneously for 5s (1 jog, 1 Long beep) Repeat step 3 Press and hold DOWN + STOP simultaneously for 5s (1 jog, 1 Long beep) Repeat step 3

Check that both upper and lower limits are set. Operate the screen to the desired preferred position. Press P2 (1 jog and 1 beep), press STOP (1 jog and 1 beep), press STOP again (2 jogs and 3 beeps), preferred position is now set Remove Preferred Press P2 (1 jog and 1 beep), press STOP (1 jog and 1 beep), press STOP again (1 jog and 1 Long beep), preferred position is now deleted Press P2 (1 jog and 1 beep), Down and 1 beep), P2 (2 jogs and 3 beeps), all limits are now removed On existing remote, Press P2 (1 jog and 1 beep) Press P2 again (1 jog and 1 beep), then on new remote, press P2 (2 jogs and 3 beeps). New remote is now linked. Repeat for any additional remotes 1. Press the LEFT and RIGHT buttons simultaneously, a “C” will appear followed by “15” 2. Press the LEFT arrow to display the desired number of channels to be displayed on the remote 3. Press the Stop Button, a square will appear on the screen, number of channels has been saved Issue – Possible Cause Solution Motor has no response - No Power or poor wire connection Check power and connections Motor has no response - Remote battery low Replace Battery Motor has no response - RF Interference Check motor antenna, check for other RF source interference Motor has no response - Out of remote control range Move remote closer to unit Remote can’t control single motor - Multiple motors paired to the same channel Use multi-channel remote to control multiple screens or single channel per screen Motor starts slow or makes loud noise - Incorrect installation or overload Verify installation is correct and level Motor stops during travel - Motor has reached limit Adjust limits Motor stops during travel - Run time exceeds 4 minutes Allow motor to cool to reset the internal thermal fuse Screen does not reach lower limit or goes too far into the housing – Screen has re- wrapped itself Remove hood and check for re-wrap, break limits if needed to relieve re-wrap Remote A → Remote A → Remote B 5 Preferred Position 6 Delete All Limits 7 Pair / Unpair Additional Remotes 8 Remove All Remotes 9 Setting Number of Channels Troubleshooting Press P2 (1 jog and 1 beep), STOP (1 jog and one beep), P2 (2 jogs and 3 beeps) 10 Motor Mode Switching Press P2 (1 jog and 1 beep), UP (1 jog and one beep), UP (1 jog and 1 long beep)