Sunex Tools 8013ADLX Manual 

4 rev. 082107 Item Part # # Req’d Description 1 * 2 Chrome Leg/ea. 2 RSSCPLW 2 Locking Caster/ea. 3 RSSCPW 2 Non-Locking Caster/ea. 4 RSSCPP1 1 Set of 4 Plastic Inserts 5 RSSCPHK 1 Bolt Kit (Incl. 8 ea. of 10mm and 14mm bolts, nuts, washers and 4 screws) 6 8011 1 Red Pry Bar Holder 8011BK Black Pry Bar Holder 8011BL Blue Pry Bar Holder 8011Y Yellow Pry Bar Holder 5 7 8004 1 Red Side Work Station 8004BK Black Side Work Station 8004BL Blue Side Work Station 8004Y Yellow Side Work Station 8 8002 1 Red Top Lid 8002BK Black Top Lid 8002BL1 Blue Top Lid 8002Y Yellow Top Lid * For replacement, purchase RSSC7, Chrome Leg, and 8014, Leg Extensions. PARTS BREAKDOWN MODEL 8013ADLX / 8013ABKDLX 8013ABLDLX / 8013AYDLX SERVICE CART WITH LOCKING TOP & DRAWERS INCLUDES PRY BAR HOLDER AND SIDE WORK BENCH Replacement Parts LIST 2 1 4 3 6 7 1 8 Part # Description RS3DHDL Short Chrome Drawer Handle RS3DHDLB Short Black Drawer Handle RS8006HDL Long Chrome Drawer Handle RS8006HDLB Long Black Drawer Handle RS8006HDLS Handle Screws (Set of 4) RSRBSLIDEC2 Clip-On Roller Bearing Slide/pr. 8006RB Red Replacement Large Drawer 8006CRBBK Black Replacement Large Drawer 8006CRBBL Blue Replacement Large Drawer 8006CRBY Yellow Replacement Large Drawer 8016 Red Replacement 3 Drawer Unit 8016BK Black Replacement 3 Drawer Unit 8016BL Blue Replacement 3 Drawer Unit 8016Y Yellow Replacement 3 Drawer Unit 8007 Red Replacement Third Shelf 8007BK Black Replacement Third Shelf 8007BL1 Blue Replacement Third Shelf 8007Y Yellow Replacement Third Shelf 8013LS 4-Piece Lock & Key Set, Keyed Alike 1110 EVA Foam for Trays / 10-pk. 1111 EVA Foam for Drawers / 10-pk. 8004SSM Rubber Liner for Side Shelf / 10-pk. ALSO AVAILABLE

 rev. 082107 Chrome Legs (2) (With Inserts Installed) Keys (Attached to Legs) Locking Casters (2) Non-Locking Casters (2) Locking Drawer Assembly 14mm Bolts, Nuts, & Washers (8 Pcs. Each) Bottom Tray Pry Bar Holder Side Work Bench Rubber Mallet Table or Workbench 10mm Wrench Phillips Head Screwdriver 2 People Long Drawer Handle (1) Drawer Handle Screws (12) Short Drawer Handles (4) TOOLS NEEDED OPERATING MANUAL THIS OPERATING MANUAL CONTAINS IMPORTANT SAFETY INFORMATION. READ CAREFULLY AND UNDERSTAND ALL INFORMATION BEFORE OPERATING THIS TOOL. SAVE THIS MANUAL FOR FUTURE USE. PARTS LIST Examine box contents, then proceed with the following instructions. MODEL 8013ADLX / 8013ABKDLX 8013ABLDLX / 8013AYDLX SERVICE CART WITH LOCKING TOP & DRAWERS INCLUDES PRY BAR HOLDER AND SIDE WORK BENCH 10mm Bolts, Nuts, & Washers (8 Pcs. Each) © Copyright 2007, Sunex Tools®

 rev. 082107 Do not fully tighten fasteners until prompted. Step 1: Assembly preparation. Clear table top and set Locking Drawer Assembly on table top, with lid facing up. Position the Locking Drawer Assembly so that one end hangs off of the table enough to allow the chrome legs to go through the square holes. Insert one set of chrome legs through the overhanging holes as shown in Figure 1. Do not bolt legs to top. Step 2: Connecting legs and side accessory to drawer assembly Choose one of the side accessories (Pry Bar Holder or Side Work Bench - Figure 2 shows Pry Bar Holder) for attachment to the overhanging end of the service cart. Align the outermost bolt holes in the accessory with the bolt holes in the end of the cart and with the uppermost holes the chrome legs. Position a washer and insert a 10mm bolt through the washer, bolt holes, and legs as shown. Secure bolts with a flat washer, lock washer, and nut on inside of Lock- ing Drawer Assembly. Tighten bolts until parts fit together firmly. Repeat steps 1 and 2 for other end of cart, using remaining side accessory. 2. 3.2 Locking Drawer Assy. Chrome Legs Table 10mm Bolt Table Pry Bar Holder Chrome Legs Locking Drawer Assy. 1. 2. Locking Top Locking Top ASSEMBLY INSTRUCTIONS NOTE

 rev. 082107 Bottom Tray 10mm Bolts Chrome Legs Step 3: Connecting the bottom tray to the chrome legs. Lift the cart and place on top of the bottom tray with chrome legs through the square leg-holes. Align bolt holes in bottom tray with lower holes in legs and insert a 10mm bolt through the washer, bolt holes, and legs as shown. Repeat with all remaining holes in bottom tray. Step 4: IMPORTANT: Tighten all bolts. At this point, all bolts should be tightened. Tighten bolts opposite each other rather than tightening all bolts on one side first so that cart remains aligned. Avoid using excessive force when tightening bolts. Over-tightening bolts can make drawers bind and hinder their operation. Step 5: Attaching handles to drawer faces. Open the bottom drawer of the service cart. Align the ends of the long handle with the edges of the bot- tom drawer, so that the channel in the handle covers all four holes in the front of the drawer. Insert screws through each hole from inside the drawer and into the drawer handle channel. Tighten the screws. Repeat for all remaining drawers using short handles. Do not allow the handles to over hang the ends of the drawer faces, as they will interfere with the operation of the drawer. Step 6: Attaching casters. With the provided keys, lock all drawers, the top, and the Pry Bar Holder to prevent them from opening. Turn the cart upside down, allowing it to rest on chrome leg tops with the plastic inserts facing up. Do not allow the Side Work Bench to swing freely, as it may be damaged or cause injury as cart is turned upside down. Insert the stem of one caster into the hole in a plastic insert. Using a rubber mallet, hammer the casters into place until the stem is no longer visible. Repeat with other casters. Ensure that both locking casters are on same end of the cart. Once casters are installed, stand cart upright. Assembly is complete. ASSEMBLY INSTRUCTIONS 3. 5. NOTE NOTE NOTE 6.