Sunbeam HTD8216C Instruction Manual

INDEX Foreword Safety Information Overview Operation Troubleshooting Cleaning, Care and Storage Replacing the Battery Disposal Warranty EMC Declaration Body temperature 3 4 10 16 21 22 23 23 24 24 30 FOREWORD The Infrared Body Thermometer Operating Instructions intend to provide the necessary information for proper operation of the HTD8216C Thermometer model. Only Body Mode was reviewed and certified. General knowledge of Infrared Thermometer and an understanding of the features and functions of the HTD8216C Thermometer model are prerequisites for proper use. The Infrared Body Thermometer is a medical device, and can be used repeatedly. The device shelf life is 5 years. Do not operate HTD8216C Thermometer without completely reading and understanding these instructions. PLEASE READ THE MANUAL FIRST BEFORE USING IT. IF THE USAGE IS NOT FULLY UNDERSTOOD, PLEASE STOP USING THE THERMOMETER. NOTICE PURCHASE OR POSSESSION OF THIS DEVICE DOES NOT CARRY ANY EXPRESS OR IMPLIED LICENSE TO USE WITH REPLACEMENT PARTS WHICH WOULD, ALONE OR IN COMBINATION WITH THIS DEVICE, FALL WITHIN THE SCOPE OF ONE OF THE RELATING PATENTS.

- 5 - SAFETY INFORMATION SAFETY INFORMATION THIS DEVICE MAY ONLY BE USED FOR THE PURPOSES DESCRIBED IN THESE INSTRUCTIONS. THE MANUFACTURER CANNOT BE HELD LIABLE FOR DAMAGE CAUSED BY INCORRECT APPLICATION. THE INFRARED BODY THERMOMETER IS DESIGNED TO MINIMIZE THE POSSIBILITY OF HAZARDS FROM ERRORS IN THE SOFTWARE PROGRAM BY FOLLOWING SOUND AND LIGHT ENGINEERING DESIGN PROCESSES, RISK ANALYSIS AND SOFTWARE VALIDATION. • DO NOT use the thermometer if it malfunctions or has been damaged in any matter. • When the ambient temperature of the thermometer changes too much, such as moving the thermometer from one room at a lower temperature to another room at a higher temperature, allow the thermometer to remain in a room for 30 minutes where the temperature is between 59℉ - 95℉ (15℃ - 35℃) before using. • Remove primary batteries if equipment is not likely to be used for long time. • This product is not waterproof, DO NOT immerse in water or other liquids; when cleaning and disinfecting, please refer to and follow the "care and storage" requirements. • DO NOT touch the sensor of infrared detection with your fingers. • If a cold compress is used to cool down, the temperature reading will be low and will not be accurate. • When measuring the forehead select "forehead" mode. when measuring ear temperature, please select the "ear" mode. • This product should only be used in a room with stable ambient temperature. Fluctuations in ambient temperature may result in inaccurate readings. • DO NOT use near strong electrostatic or magnetic fields to avoid impact on the accuracy of the measurement data. • DO NOT mix the old and new batteries to avoid damage to the product.

- 7 - • Brush aside any hair and make sure the forehead is clean and free of perspiration, cosmetics, or any coverings (hats, caps, scarves) that may interfere with measuring. • Measurement results are for reference only. Contact your physician if you have or suspect a medical condition. • Ensure the ear canal is clean and dry before using the "ear" mode as this may interfere with the measurement. WARNINGS The device should be kept out of the reach of children / pets. When not in use, store the device in a dry room and protect against extreme moisture, heat, lint, dust and direct sunlight. Never place any heavy objects on the thermometer. DO NOT throw batteries into fire. DO NOT discard in household trash. Only use recommended batteries. DO NOT use rechargeable batteries. This thermometer is not intended as replacement for advice from a physician or medical professional. DO NOT drop, disassemble or modify the device. DO NOT use this device if you think it is damaged or notice anything unusual. SAFETY INFORMATION

- 9 - This device comprises sensitive components and must be treated with caution. Observe the storage and operating conditions described in the ’Technical Specifications’ section. DO NOT perform service or maintenance while the Thermometer is in use. While in use DO NOT touch the battery and the person at the same time. DO NOT use the Thermometer if it is damaged, degraded or loosened in any way. Continuous use of a damaged Thermometer may cause injury, improper results, or serious danger. Based on the current science and technology, other potential allergic reactions are unknown. This devise needs to be used and serviced in accordance with the information provided in this INSTRUCTION MANUAL. WARNINGS INTENDED USE The Infrared Body Thermometer, Model: HTD8216C, is an electronic clinical thermometer using an infrared sensor to detect body temperature from the forehead or auditory canal in people of all ages for home setting use. The Sunbeam Thermometer is a hand-held, reusable, battery operated device, which can measure human body temperature on the forehead and in the ear. It can also measure the surface temperature of objects. The operation principle is based on Infrared Sensor technology. The IR sensor can output different signals when measuring different object temperatures or in different ambient temperatures, and the ASIC can turn the signal from IR Sensor to a digital value and display it on the LCD. CONTRAINDICATIONS: 1. DO NOT measure areas on the forehead with scar tissue or tissue compromised by skin disorders as this can affect the measurement accuracy. 2. DO NOT measure temperature of persons in trauma. 3. DO NOT use if being treated with drug therapies that can increase the body temperature. 4. DO NOT measure temperature on sites of the skin exposed to external sources of heat or cold such as direct sunlight, fireplace heat, cold compress, air conditioner flow, etc.

- 11 - INFRARED BODY THERMOMETER COMPONENTS INFRARED BODY THERMOMETER COMPONENTS 1 1 2 2 4 3 3 5 4 6 5 7 9 6 8 Cap Ear mode Measuring status indicator Liquid crystal display (LCD) Data indicator Battery cover Low battery indicator Volume on/off indicator Mode button (inside cover) Indicator of measurement result Memory indicator Passive infrared probe Forehead mode START button Measurement unit 3 6 4 5 1 2 Figure 1 Model : HTD8216C Figure 2 Model : HTD8216C 1 7 8 2 3 4 5 6 9

- 13 - Thermometer Model # Thermometer Style Adult Pediatric Ear Forehead Ear Forehead HTD8216C Infrared Body Thermometer √ √ √ √ Warning Operating atmospheric pressure Non sterile Packaging Type BF (Body Floating) Consult instructions for use Compliance with WEEE Standard Operating Temperature DO NOT THROW AWAY Intended for multiple use Operating Humidity Serial number Manufacturer Restriction of Hazardous Substances Recyclable Batch code This device compiles with Part 15 of FCC ( Federal Communications Commission) Rules IP22: The first number 2: Protected against solid foreign objects of 12.5mm Ø and greater. The second number: Protected against vertically falling water drops when enclosure titled up to 15º. LOT Measurement Unit ºF / ºC Operating mode Forehead mode / Ear mode Measuring site Forehead / Ear Reference Body Site Axillary Output Range Body mode: 93.2°F - 109.2°F / 34.0ºC - 42.9ºC Surface mode: 32°F - 212°F / 0ºC - 1 00.0ºC Laboratory Accuracy Forehead mode/Ear mode: 93.2°F - 94.8°F: ±0.5°F / 34.0ºC - 34.9ºC: ±0.3ºC; 95.0°F - 107.6°F: ±0.4°F / 35.0 - 42.0ºC:±0.2ºC; 107.8°F - 109.2°F: ±0.5°F / 42.1 - 42.9ºC:±0.3ºC; Display Resolution 0.1°F / 0.1ºC Three-color Backlight (Color Alarm) 93.2°F - 99.1°F / 34°C - 37.3°C Green (Normal Temperature); 99.3°F - 100.4°F / 37.4°C - 38.0°C (Alarm point) Yellow (Slight Fever) 100.6°F - 109.2°F / 38.1°C - 42.9°C Red (High Fever) Note: Color Alarm is only for Body mode Auto Power Off Time ≤35s Measuring Time ≤5s (under ear mode); ≤2s (under Forehead mode) Memories 1 Power Supply Requirements Batteries DC 3V (2 x 1.5V AAA batteries) Environmental Conditions Operating Condition Operating Temperature: 59°F - 95°F (15°C - 35°C), Relative Humility≤85%, atmospheric pressure: 70 - 106Kpa Transport and Storage Condition Storage Temperature: -4°F - 131°F / -20°C - 55°C Relative Humility≤93%, atmospheric pressure: 70 - 106Kpa THERMOMETER APPLICATIONS TECHNICAL SPECIFICATIONS EQUIPMENT SYMBOLS Note: not all symbols may appear in this instruction manual

- 15 - Weight (without batteries) 2.3oz (65g) Size 6.1" x 1.3" x 2" (154mm x 33mm x 51mm) Item Compliant with Equipment classification Safety Standards: EN 60601-1: 2006+A1:2013, EN 60601-1-2: 2015 Type of protection Internally powered equipment (on battery power) Degree of protection Non Applied part Front panel and case labeling EN ISO15223 -1:2012 Temperature EN ISO80601 - 2 - 56:2012 Home healthcare environment EN 60601 - 1 - 11:2015 Accessory name Number AAA battery 2 Instruction Manual 1 DIMENSION AND WEIGHTING CALCULATED VALUES OF THE INDICATORS ACCORDING TO ISO 80601-2-56-2012 EAR MODE: FOREHEAD MODE: SAFETY CLASSIFICATION OF ME EQUIPMENT Indicators Calculated value Clinical bias, Δcb 0.009 Standard deviation, ∑ j 0.11 Limits of agreement, LA 0.19 Clinical repeatability, ∑ r 0.06 Indicators Calculated value Clinical bias, Δcb -0.018 Standard deviation, ∑ j 0.13 Limits of agreement, LA 0.26 Clinical repeatability, ∑ r 0.06 Protection against electric shock Internally powered ME equipment Degree of protection Type BF - Applied part (the probe) Protection against harmful ingress of water or particulate matter IP22 Mode of operation Continuous operation NOTE: Not intended to be sterilized. Not for use in an OXYGEN RICH ENVIRONMENT

- 17 - OPERATION INSTALLING BATTERIES 1. Remove the battery access cover. 2. Insert two (2) AAA batteries aligned with the “+” and “-” icons. 3. Close the battery access cover. • Install new batteries when the battery level indicator is low • Dispose of/recycle used batteries following local regulations to avoid environmental pollution. BEFORE TAKING A TEMPERATURE To maximize results: • Choose a room or area with stable surrounding temperature, away from direct sunlight or strong airflow sources such as fans or air conditioners. • Allow the thermometer at least 30 minutes to adjust to surrounding room temperature (if moving the device to or from a warmer or cooler location) before use. • Allow the body at least five minutes to adjust to surrounding room temperature. • If a cool compress on the forehead or other measures are taken to reduce fever, the temperature data will be low. You may also try measuring behind the ear or in EAR MODE for comparison. • Brush aside any hair and make sure the forehead is free of perspiration or head coverings (hats, caps, scarves) when using FOREHEAD MODE. • Make sure the ear canal and probe are clean when using EAR MODE. OPERATION GETTING STARTED Press the START button • The thermometer will perform a self-test with all functions displayed for 2 seconds. (See Figure 2) • An audio signal (three “beeps”) will confirm the self-test is complete. • The display will show the last measured temperature stored in memory. (See Figure 3) • When the device is ready, the memory symbol will disappear and the unit symbol will start flashing. (See Figure 4) Figure 2 Figure 4 Figure 3

- 19 - OPERATION SELECTING FOREHEAD, EAR To measure human BODY temperature (factory default): • When the cap is off, the thermometer will measure in EAR MODE. • When the cap is on, the thermometer will measure in FOREHEAD MODE. NOTE To change back to FORHEAD MODE if the bottle icon appears , follow the below steps: • Open the battery access panel. • With the thermometer ON, press the small MODE button inside the battery compartment to select FOREHEAD MODE (head icon appears on the display ). • Replace the battery access cover. OPERATION MEASURING BODY TEMPERATURE IN FOREHEAD MODE Note: Thermometer Cap should be on. 1. Press START to turn on • A short beep will indicate ready to measure. 2. Hold the device vertically in front of the forehead. 3. Press START to begin measuring. • A series of “beeps” will indicate measuring is complete. 4. The LCD display will show the target value of the measured temperature. 5. The backlit screen will indicate a color alert for body temperature (FOREHEAD AND EAR MODE) measurements. Green - Normal Temperature/Ready for Measurement Yellow - Slight Fever WARNING Red - High Fever WARNING Test at least 3 times and select the result that appears most.

- 21 - OPERATION MEASURING BODY TEMPERATURE IN EAR MODE Note: Remove Thermometer Cap to access ear probe. If the patient is more than one year old, pull the ear up and back gently. If the patient is less than one year old, pull the ear back gently. (See Figure 5) 1. Press START to turn on. Insert the thermometer probe slowly into the ear canal • A short beep will confirm ready to measure. 2. Press START to begin measuring. • A series of “beeps” will confirm measuring is complete. 3. The LCD display will show the target value of the measured temperature. 4. The backlit screen will indicate a color alert for body temperature (FOREHEAD AND EAR MODE) measurements. Green - Normal Temperature / Ready for Measurement Yellow - Slight Fever WARNING Red - High Fever WARNING Test at least 3 times and select the result that appears most. TROUBLESHOOTING MESSAGE SITUATION SOURCE OR SOLUTION Temperature taken in is higher than Typical human temperature Body mode: detected target temperature higher than 109.2°F (42.9°C) Temperature taken in is lower than Typical human temperature Body mode: detected target temperature lower than 93.2°F (34°C) Operating temperature exceeds the range of specified temperature Environment temperature higher than 95°F (35°C) or lower than 59°F (15°C) Wrong function indicated System failure found when System auto-check, the screen flicker, and automatic turn off. Battery capacity is too low. Taking Temperature is not allowed Install new batteries Ambient temperature is unstable Ambient temperature is unstable. Please allow it to acclimate for at least 30 minutes before using it. Blank screen indicate • Press ON button again • Check the battery polarity • Replace with new batteries The internal time from the first measurement to next measurement is less than 5 seconds under ear mode. Please wait 5 seconds to take next measurement. Measurement results unavailable because the thermometer was removed from position too quickly or was not in place properly (for the ear mode). 1. Hold the thermometer in place until it signals the measurement is complete for forehead mode. 2. Ensure the probe is correctly inserted in the ear canal under ear mode. Mode switch error Check if the thermometer cap is securely in place under forehead scan mode. Ensure the cap is completely removed under ear mode. Figure 5 >1 year <1 year

- 23 - REPLACING THE BATTERIES 1. Open and release battery cover following indicator on the surface of shell. Before changing the batteries be sure the system is already power off. 2. Press the battery holder lock to release the batteries. 3. Remove the batteries and replace with 2 new, type AAA. Make sure the positive pole of the battery facing up. 4. Slide the battery cover back in until it snaps in place. WARNING DO NOT RECHARGE, DISASSEMBLE OR DISPOSE OF BATTERIES IN FIRE. DISPOSAL AND RECYCLING • At the end of this device’s useful product life, follow local regulations for appropriate and environmentally-friendly recycling or disposal. • Do not discard thermometers or used batteries in regular household trash. Please follow local regulations for appropriate and environmentally-friendly recycling or disposal. LIMITED 3-YEAR WARRANTY This product has a limited warranty of 3 years from the original date of purchase against workmanship and defects in material. If under normal use, your product fails to operate, please contact our customer service department at info@stareliteinc. com. A refund or replacement will be provided to you with proof of purchase. Star Elite Inc. may deny claims of damage caused by misuse or modifications of this product. CLEANING, CARE AND STORAGE Note: The thermometer lens and infrared probe are delicate. Handle with care and keep them protected from dirt and damage. Do not touch the lens or probe with fingers or tools. 1. Gently wipe the thermometer probe, lens, device surface and LCD screen with a soft, clean cloth or cotton ball moistened with 70 - 75% isopropyl sterilizing alcohol. • Do not use solvents or immerse the device in water or other liquids. 2. Clean and sterilize the thermometer before and after each use to avoid cross-contamination. 3. If the thermometer will not be used regularly, remove the batteries to prevent damage during storage. 4. Store the thermometer in a clean, dry location free from dust, humidity, and temperature extremes. • Recommended storage temperature range is -4°F - 131°F / -20°C - 55°C relative humidity ≤93%, atmospheric pressure: 70 - 106KPA 5. When removing from storage, allow at least 30 minutes for the thermometer to reach stable room temperature before it is ready for use. 6. Periodically inspect the device and discontinue use if you notice visible damage.

- 25 - Guidance and manufacture’s declaration - Electromagnetic emission The Infrared Body Thermometer is intended for use in the electromagnetic environment specified below. The customer of the user of the Infrared Body Thermometer should assure that it is used in such an environment. Emission test Compliance Electromagnetic environment – guidance RF emissions CISPR 11 Group 1 The Infrared Body Thermometer use RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment. RF emissions CISPR 11 Class B The Infrared Body Thermometer is suitable for use in all establishments, other than domestic and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes. Harmonic emissions IEC 61000-3-2 Not applicable Voltage fluctuations/ flicker emissions IEC 61000-3-3 Not applicable Guidance and manufacture’s declaration - Electromagnetic immunity The Infrared Body Thermometer is intended for use in the electromagnetic environment specified below. The customer or the user of Infrared Body Thermometer should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Electromagnetic environment – guidance Electrostatic discharge (ESD) IEC61000-4-2 ±6kV contact ±8 kV air ±6kV contact ±8 kV air Floors should be wood, concrete or ceramic tile. If floor are covered with synthetic material, the relative humidity should be at least 30%. Electrical fast transient / burst IEC 61000-4-4 ±2 kV for power supply lines ±1 kV for input/output lines Not applicable Mains power quality should be that of a typical commercial or hospital environment. NOTE: The thermometer is initially calibrated at the time of manufacture. If this thermometer is used according to the use instructions, periodic re-adjustment is not required. If at any time you question the accuracy of the temperature measurements, please contact our customer service department. EMC DECLARATION 1. This equipment needs to be installed and put into service in accordance with the information provided in the ACCOMPANYING DOCUMENTS; This product needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided, and this unit can be affected by portable and mobile RF communications equipment. 2. Do not use a mobile phone or other devices that emit electromagnetic fields, near the unit. This may result in incorrect operation of the unit. 3. Caution: This unit has been thoroughly tested and inspected to assure proper performance and operation! 4. Caution: this machine should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary, this machine should be observed to verify normal operation in the configuration in which it will be used.

- 27 - Guidance and manufacture’s declaration - Electromagnetic immunity The Infrared Body Thermometer is intended for use in the electromagnetic environment specified below. The customer or the user of Infrared Body Thermometer should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Electromagnetic environment – guidance Surge IEC 61000-4-5 ± 1 kV line(s) to line(s) ± 2 kV line(s) to earth Not applicable Mains power quality should be that of a typical commercial or hospital environment. Electrical fast transient / burst IEC 61000-4-4 ±2 kV for power supply lines ±1 kV for input/output lines Not applicable Mains power quality should be that of a typical commercial or hospital environment. Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11 <5% UT (>95% dip in UT) for 0.5 cycle 40% UT (60% dip in UT) for 5 cycles 70% UT (30% dip in UT) for 25 cycles <5% UT (>95% dip in UT) for 5 sec Not applicable Mains power quality should be that of a typical commercial or hospital environment. If the user of the Infrared Body Thermometer requires continued operation during power mains interruptions, it is recommended that the Infrared Body Thermometer be powered from an uninterrupted power supply or a battery. Power frequency (50Hz/60Hz) magnetic field IEC 61000-4-8 3 A/m 3 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. NOTE: UT is the a.c. mains voltage prior to application of the test level. Guidance and manufacture’s declaration - Electromagnetic immunity The Infrared Body Thermometer is intended for use in the electromagnetic environment specified below. The customer or the user of Infrared Body Thermometer should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Electromagnetic environment – guidance Conducted RF IEC 61000-4-6 3 Vrms 150 kHz to 80 MHz Not applicable Portable and mobile RF communications equipment should be used no closer to any part of the Infrared Body Thermometer, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance d= 1.2 d= 1.2 80MHz to 800MHz d= 2.3 80MHz to 2.5GHz Where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey,a should be less than the compliance level in each frequency range.b Interference may occur in the vicinity of equipment marked with the following symbol: Radiated RF IEC 61000-4-3 3 V/m 80 MHz to 2.5 GHz 3 V/m P P P

- 29 - Guidance and manufacture’s declaration - Electromagnetic immunity The Infrared Body Thermometer is intended for use in the electromagnetic environment specified below. The customer or the user of Infrared Body Thermometer should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Electromagnetic environment – guidance NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. a Field strengths from fixed transmitters, such as base stations for radio (cellular/ cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the Infrared Body Thermometer is used exceeds the applicable RF compliance level above, the Infrared Body Thermometer should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the Infrared Body Thermometer. b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. Recommended separation distances between portable and mobile RF communications equipment and the Infrared Body Thermometer. The Infrared Body Thermometer is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the Infrared Body Thermometer can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the Infrared Body Thermometer as recommended below, according to the maximum output power of the communications equipment. Rated maximum output power of transmitter (W) Separation distance according to frequency of transmitter (m) 150 KHz to 80 MHz d= 1.2 80 MHz to 800 MHz d= 1.2 800 MHz to 2.5 GHz d= 2.3 0.01 0.12 0.12 0.23 0.1 0.38 0.38 0.73 1 1.2 1.2 2.3 10 3.8 3.8 7.3 100 12 12 23 For transmitters rated at a maximum output power not listed above, the recommended separation distanced in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. P P P

- 31 - BODY TEMPERATURE For consumer use only, not for professional use. • Body temperature varies from person to person and fluctuates during the course of the day. For this reason, it is suggested to know one's normal, healthy forehead temperature to correctly determine the temperature. • Body temperature runs approximately from 95.9°F - 100°F • (35.5°C - 37.8°C). To determine if one has a fever, compare the temperature detected with the person's normal temperature. A rise over the reference body temperature of 1°F (1°C) or more is generally indication of fever. • Different measurement sites (rectal, axillary, oral, frontal, auricular) will give different readings. Therefore it is wrong to compare the measurement taken from different sites. • Here below are typical temperatures for adults, based on different measurement sites: Rectal: 97.9°F - 100.4°F / 36.6°C - 38°C - Axillary: 94.5°F - 99.1°F / 34.7°C - 37.3°C BODY TEMPERATURE ASTM laboratory accuracy requirements in the display range of 96.8°F - 102.2°F (36°C - 39°C) for IR thermometers is ±0.4°F (±0.2°C), whereas for mercury in-glass and electronic thermometers, the requirement per ASTM Standards E667-86 and E1112-86 is ±0.2°F (±0.1°C). Caution: This infrared thermometer meets requirements established in ASTM Standard (E1965-98) Except of clause 5.2.2. It displays subject’s temperature over a range of 93.2°F - 109.2°F (34.0°C - 42.9°C). Full responsibility for the conformance of this product to the standard is assumed by Star Elite Inc. 1175 Place du Frère André, Montreal, QC, Canada H3B 3X9

Contact our customer service at 1-877-383-6399 (8:30 am - 5:00 pm EST) Monday - Friday or contact us at [email protected] Our customer service will be happy to assist you. © 2021 Sunbeam Products, Inc. All rights reserved. Distributed by Star Elite Inc., Montreal, Canada H3B 3X9. SE003-062821 Infrared Body Thermometer Model HTD8216C Printed in China