Starline AL8C Operator's Manual

15 DESCRIPTION PART NO REC. STOCK Pumps and Solenoids • Condenser Fan 600 30503 1 • Detergent Pump 600 30526 1 • Detergent Squeeze Tube 600 30134 1 • Rinse Aid Pump 600 30480 1 • Rinse Aid Squeeze Tube 400 30119 1 • Rinse Pump 600 30400 1 • Solenoid Valve 1 Way 3342 1 • Wash Pump 3906 1 Wash Tank Components • Drain Upstand 305mm 400 10145 1 • Locknut Wash Arm 280409C 1 • Pressure Bell 400 90135 1 • Rack Slide Assembly 354 11029 1 • Rinse Arm Assembly 400 10239 1 • Rinse Arm Bush C190624 2 • Rinse Arm Cap Screw 261004C 2 • ...

POSITION LEVEL AND STABLE? ON SOUND, WATERPROOF, SELF-DRAINING FLOOR WATER ISOLATOR VALVE FITTED? ACCESSIBLE, ALL FITTINGS SOUND, AND NO LEAKS TEMPERATURE CORRECT (65°C)? HIGH TEMP SOLENOID IF ABOVE RANGE PRESSURE CORRECT (< 350 kPa)? LIMITER FITTED IF ABOVE RANGE, RINSE PUMP IF BELOW FLOW RATE CORRECT? RINSE PUMP FITTED IF BELOW REQUIREMENT QUALITY WITHIN REQUIREMENTS? FILTER OR SOFTENER IN PLACE IF OUTSIDE REQUIREMENTS POWER ISOLATING SWITCH? FITTED, FUNCTIONAL AND ACCESSIBLE CORRECT SUPPLY (3p/25A 400V 50Hz ...

14 DESCRIPTION PART NO REC. STOCK Cabinet & Door • Control Panel Sub-Assembly 354 14008 1 • Control Panel Label 400 70189 1 • Spring Door 27 x 735 x 5 326 30019 1 Controls & Indicators • Contactor 600 30337 1 • Start Button 600 30566 1 • Door Reed Switch 600 30183 1 • Knob 4 Position 600 30524 1 • Power Light 600 30529 1 • Pressure Switch Wash 600 30479 1 • Pressure Switch Break Tank 400 10214 1 • Relay 2 Pole 240V 600 30080 1 • Relay Base 600 30081 1 • Switch 4 Position 600 30269 1 • Temperature Gauge 600 30515 1 • Termina ...

7 Water Quality Requirements The incoming water should also be within the following parameters: Hardness ppm pH min 20 7 max 100 8 Ions Cl- SO4 Fe Mn Cu Cl2 Max mg/L 100 400 0.1 0.5 0.05 0.1 NOTE: Levels above or below the stated requirements can be expected to increase component wear and reduce the expected useful life of the dishwasher. If in doubt, it is best to consult a water specialist and have the incoming water professionally tested and treated if necessary. Power • Electrical supply required is 3p/25A ...

2 Warnings Before installation and commissioning, you must read the safety instructions and warnings carefully and all the warning labels attached to the equipment. Equipment contains dangerous voltages and can be hazardous if installed or operated incorrectly. Non-compliance with warnings or failure to follow the instructions contained in this manual can result in loss of life, severe personal injury or serious damage to property. Before installation or repair, you must read the instructions and warnings carefully and all the warning labels attached to ...

• Turn Cycle Selector to 0 and turn off the power from the wall. • Remove Scrap Trays (1) and Upstand (2) to drain the Wash Tank. • Once the Wash Tank is fully drained remove and rinse Wash Pump Filter (3) and Scrap Trays (1) before replacing back into the machine along with the Upstand (2). CLEANING – AT LEAST ONCE A WEEK Remove, rinse and replace when machine has cooled down: Scrap Trays 1 Drain Upstand 2 Wash Pump Filters 3 Rinse Arms 4 Wash Arms 5 Thumbscrews 6 Inspect and clear all jets in the upper and lower Wash/Rinse Arms using a small object such as a t ...

7 Water Quality Requirements The incoming water should also be within the following parameters: Hardness ppm pH min 20 7 max 100 8 Ions Cl- SO4 Fe Mn Cu Cl2 Max mg/L 100 400 0.1 0.5 0.05 0.1 NOTE: Levels above or below the stated requirements can be expected to increase component wear and reduce the expected useful life of the dishwasher. If in doubt, it is best to consult a water specialist and have the incoming water professionally tested and treated if necessary. Power • Electrical supply required is 3p/25A ...

13 Accessories AL8C Accessories • Part #: AL8C ACW • Date: 13/12/2017 • Version: 1-A ...