Speakman CPT-24400 Instructions

92-CPT-24400-01 For additional assistance or service please contact: SPEAKMAN® Company 400 Anchor Mill Road New Castle, DE 19720 800-537-2107 [email protected] www.speakman.com CPT-24400 TOOLS AND SUPPLIES Phillips Screwdriver Measuring Tape Hex Key Wrench (Included) Additional warranty information can be found at: www.speakman.com WARRANTY MAINTENANCE Cover your drain to prevent loss of parts. SAFETY TIPS IMPORTANT • Be sure to read instructions thoroughly before beginning installation. • Do not over-tighten any connections or damage may occur. Your new Speakman Product is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft cloth. The use of harsh chemicals and abrasives on any of the Speakman custom finish products may damage the finish and void the product warranty. Please be sure to only use approved cleaners. Please contact Speakman for any clarification of acceptable cleaners. 1 Clean wall surface. Place Mounting Base (1) onto the valve, align mounting holes, and secure with supplied screws (2). 2 There are two connectors included to allow for both Shallow Mount (Valve Centerline is 2.5-3.0” from finished wall surface) and Deep Mount (Valve Centerline is 3.0”-3.5” from finished wall surface) applications. Please select Connector appropriate for your installation. For Deep Mount Application For Shallow Mount Application 3 Confirm that the valve is in the “OFF” position. Place appropriate Connector (5) onto spindle of valve making sure to orient the Connector so that one set of splines are perfectly vertical as shown below. 4 When installed correctly, the Connector (5), should extend beyond the Mounting Base in-between 1/8” -1/2”. Secure with screw (6). If your installation does not fall within this range, try swapping Connectors. IMPORTANT 1/8”-1/2” 5 Place Wall Plate (3) onto Mounting Base. Align the flat tabs on the Mounting Base with the cut outs on the Wall Plate as shown for perfect fit. Verify the Diverter Valve Stem is in the OFF (vertical) position. Align the Diverter Drive Tube (4) on the Wall Plate to the Stem (5) of the Diverter Valve. * VIEW FROM BACK OF WALL PLATE 6 Orient the Handle Assembly (1) as shown below. Place Handle Assembly (1) onto the Mounting Base while guiding the splines of the Adapter (2) into the Handle Assembly (1). Align the Mounting Base Tabs (3) into the corresponding recesses of the Handle Assembly (1). Once all items are aligned, press Handle Assembly (1) inward toward Wall Plate. Secure Handle Assembly (1) by tightening Set Screw (4) with supplied Allen Wrench.

SPEAKMAN ® DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE. VALVE MOUNTING IS SHOWN FOR REFERENCE ONLY. VALVE IS NOT INCLUDED WITH CPT-24000 1" 25mm HOLE FOR SHOWER ARM 5 1 2 " 140mm HOLE FOR VALVE ACCESS 1" 25mm HOLE FOR TUB SPOUT 6'-6" [2 METERS] TO FLOOR 4'-6" [1.4 METERS] TO FLOOR (SHOWER INSTALLATION ONLY) 1'-9" [533mm] 4" [102mm TO TOP OF TUB LEDGE A A 1/2 NPT FEMALE 1/2" SWEAT CONNECTION 1/2" SWEAT CONNECTION 2-1/2"MIN [64mm] 3-1/2"MAX [89mm] (ADJUSTMENT) 4 15 16 " 125mm 1/2" SWEAT CONNECTION 8 7 16 " 215mm 6 7 8 " 175mm 3 5 16 " 83.96mm 1 5 16 " 33.30mm 13 16 " 21mm CPT-24400 REPAIR PARTS SPEAKMAN ® ITEM NO. PART NO. DESCRIPTION RPG05-0874 MOUNTING HARDWARE RPG04-104273 HANDLE/ESCUTCHEON/SET SCREW RPG10-104277 DIVERTER TRIM PLATE