SPARKLE 417/8385 Assembly Instructions Manual

or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Important - Please read these instructions fully before starting assembly Dimensions Width - 70.3cm Depth - 51.6cm Height - 182.3cm Sparkle - 2 Door Robe Assembly Instructions - Please keep for future reference Issue 3 - 02/10/15 417/8385 414/1343 413/3052

Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 46kgs. Please lift with care. • Check you have all the components and tools listed on pages 2 and 3. • Remove all fittings from the plastic bags and separate them into their groups. • Keep children and animals away from the work area, small parts could choke if swallowed. • Parts of the assembly will be easier with 2 people. • Make sure you have enough space to layout the parts before starting. • Do not stand or put weight on the product, this could cause damage. • Assemble the item as close to its final position (in the same room) as possible. • Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton). 1 Care and maintenance • Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. • From time to time check that there are no loose screws on this unit. • This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference. • We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. • Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice. • Dispose of all packaging carefully and responsibly. Rule Tools required Rule Scissors Square Spirit level Hammer Bradawl Eye protection (when using a hammer or drill) Cross-head screwdriver Step ladder Electric drill (only use when drilling into walls)

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below When applicable, remove any protective film before use 2 1 2 4 7 Left Side (DF3837) (180.8 x 49.4cm) Rail (DF3840) (66.9 x 8cm) x 2 Horizontal (DF3841) (66.9 x 49.2cm) x 2 Right Side (DF3838) (180.8 x 49.4cm) 3 Top (DF3839) (70.3 x 51.6cm) Door (DF3842) (172.4 x 34.5cm) x 2 Back (X1738-695) (173.8 x 69.5cm) 5 8 Hanging Rail (FHR663) (66.3cm long) 6

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 3 Ruler - Use this ruler to help correctly identify the screws mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 A B D E F G H C J K Large locking nut (F900) x 16 Metal dowel (F901) x 16 Wooden dowel (F22) x 16 L Rail Holder (F891) x 2 13mm Screw (F63) x 20 Hinge plate (F523) x 8 Strap Screw Washer x 2 Overbalance protector kit (F269) x 1 Nail (F51) x 30 Plastic Nail (F91) x 4 Hinge (F522) x 8 I 25mm Screw (F50) x 6 Handle (F569) x 2 Important: Always pair up the hinges with the hinge plates from the same bag. DO NOT mix them up. * * * * * *

a: Screw 6 metal dowels into the left side . Note: Tighten the metal dowels up fully against the panels. Insert 2 large locking nuts into the left side . Note: The arrow on the locking nut must point towards the hole in the edge of the panel. Tap 2 wooden dowels into the left side . Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels. b: To fit the rail holder screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole. Fit 4 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge. A 1 1 C 1 Step 1 A F D F D F F D 10mm C A A A A A A B B B J J J J J B D F 1 F J 1 1 1 b: a:

horizontals Insert 4 large locking nuts into each of the horizontals . Tap 4 wooden dowels into each of the horizontals . A C Assembly Instructions 5 Step 2 A A A A A A C B B J J J J J F F D Finished front edge Finished front edge Prepare the right side a: Screw 6 metal dowels into the right side . Insert 2 large locking nuts into the right side . Tap 2 wooden dowels into the right side . b: To fit the rail holder screw through the top hole with screw and into the mark hole drilled in the right side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole. Fit 4 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge. A 2 2 C 2 B 4 C 4 B D F 2 F J 2 2 2 b: a: B B B B A A A Step 3 x 2 4 Finished front edge

to the right side Push the 2 horizontals onto the right side . Use a screwdriver to tighten the 2 large locking nuts fitted to each horizontal . Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn. 2 4 B B 4 2 4 4 Prepare the 2 rails Insert 2 large locking nuts into each of the rails . Tap 2 wooden dowels into each of the rails . 5 C 5 B Step 5 x 2 Finished front edge B B A 5

Push the 2 rails onto the right side . Use a screwdriver to tighten the large locking nut fitted to each rail . . 2 5 B 5 5 5 Fit the left side Push the left side onto the assembly. Use a screwdriver to tighten the 6 large locking nuts fitted to the horizontals and the rails . 1 B 5 4 5 5 4 1 Note: Support this rail until the left side has been fitted in the next step. 4

Screw 6 metal dowels into the top . A 3 A A A A Finished front edge 3 3 Fit the top Note: To make it easier to fit the top and base panels, place polystyrene blocks from the packaging underneath the side panels to raise the assembly. Push the top onto the assembly. Use a screwdriver to tighten the 2 large locking nuts fitted to each side and . 3 B 1 2 1 2 Polystyrene block Polystyrene block

a: Square up the unit by making sure that measurement x to x equals y to y. b: Place the back onto the unit. Nail around the outside edges of the back . Note: Nails should be spaced about 150mm apart. Stand the unit up for the next step. 8 G The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y a: 8 x G 8 Step 11 Fit the 4 plastic nails Tap 2 plastic nails into the bottom edge of each of the sides and . . Carefully stand the unit up for the next step. H 1 2 H H H H 1 2 Warning: The unit is heavy. Lift with care.

Push the hanging rail into the rail holders fitted to the side panels. 6 D Step 13 Prepare the 2 doors Push fit 4 hinges into each of the 2 doors . Secure each hinge with 2 screws . Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door. F K 7 90 K x 2 K F F K F F K F F K F F 7

Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges. a: Push the hinge onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate. b: Keep the hinge FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A. c: The hinge must be flat against the hinge plate prior to any adjustment. d: The hinge must NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c. e: Attach a handle to each door using 3 screws . K K K J J J K J I E 7 7 a: b: c: d: J K J J B J K K K A K J B e: E I E E 7 7 I

needed a: Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown. b: Height adjustment. Loosen screws A on hinge plates and move door up or down as required. Retighten screw A. c: Forward and Back adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B. d: Sideways adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C. A A B C

or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 13 Step 16 Fit the overbalance protector To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . to the unit, or an alternative fixing method of your choice. Wall fixings are not supplied as they will need to suit the wall type. Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert. Assembly is complete L L WALL Wall fixing (not supplied) Screw (not supplied) Washer Strap L Strap Washer Screw TOP OF UNIT L

or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Important - Please read these instructions fully before starting assembly Dimensions Width - 38.1cm Depth - 39.6cm Height - 57.1cm Sparkle - 3 Drawer Bedside Assembly Instructions - Please keep for future reference Issue 2 - 02/10/15 411/3436 418/1035 428/7094

Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 14kgs. Please lift with care. • Check you have all the components and tools listed on pages 2 and 3. • Remove all fittings from the plastic bags and separate them into their groups. • Keep children and animals away from the work area, small parts could choke if swallowed. • Parts of the assembly will be easier with 2 people. • Make sure you have enough space to layout the parts before starting. • Do not stand or put weight on the product, this could cause damage. • Assemble the item as close to its final position (in the same room) as possible. • Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton). • We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. • Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied). • Dispose of all packaging carefully and responsibly. 1 Care and maintenance • Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. • From time to time check that there are no loose screws on this unit. • This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below When applicable, remove any protective film before use 2 1 2 3 5 6 Left Side (DF3853) (55.6 x 37.2cm) Rail (DF3807) (34.7 x 6cm) x 2 Right Side (DF3854) (55.6 x 37.2cm) Top (DF3806) (38.1 x 39.6cm) Drawer Front (DF3808) (36.7 x 16.2cm) x 3 Drawer Back (W314-124) (31.4 x 12.4cm) x 3 Drawer Base (T325-367) (32.5 x 36.7cm) x 3 Back (X531-373) (53.1 x 37.3cm) Left Drawer Side (W370-124LH) (37 x 12.4cm) x 3 Right Drawer Side (W370-124RH) (37 x 12.4cm) x 3 7 4 8 9 10

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Tools required 3 Ruler - Use this ruler to help correctly identify the screws mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 A B D E F G H I L Small locking nut (F3) x 6 C Nail (F51) x 14 M J 9mm Screw (F74) x 6 K 9mm Screw (F73) x 12 Drawer runner (F1004) x 6 Knock-in Peg (F171GY) x 12 Large locking nut (F900) x 8 Metal dowel (F901) x 14 Wooden dowel (F22) x 8 Wedgefix (F639) x 6 Rule Scissors Hammer Eye protection (when using a hammer or drill) Cross-head screwdriver Handle (F437) x 3 25mm Screw (F50) x 6 Plastic Nail (F91) x 4

fronts Screw 2 metal dowels into each of the drawer fronts . Note: Tighten the metal dowels up fully against the panels. A 5 Prepare the drawer sides Insert a small locking nut into the hole shown on the left drawer side and the right drawer side . Note: The arrow on the locking nut must point towards the hole in the edge of the panel. Step 3 C 6 7 Attach the drawer sides to the drawer fronts Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts . Turn the small locking nuts on the left drawer side and right drawer side . Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn. 6 7 5 C C 6 7 6 7 A A 5

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front . Step 5 Fit the drawer back Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back . Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and . Step 6 9 6 7 5 8 6 7 9 8 8 F Attach the handles Attach a handle to each of the drawer fronts . using screws . Note: Do not overtighten the screw. L G 5 6 7 Step 7 Fit the wedgefixes Turn the 3 drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws. K x 3 x 3 x 3 F F x 3 K K K 9 6 8 6 7 9 7 G G L 5

a: Place 3 runners on the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw . b: Slide the runner back the other way and fit the 2nd screw into the corresponding hole in the left side . c: Screw 2 metal dowels into the left side . Insert 2 large locking nuts into the left side . . Note: The arrow on the locking nuts must point towards the hole in the edge of the panel. Tap 2 wooden dowels into the left side . Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels. D D Finished front edge Finished front edge Assembly Instructions 6 Step 8 B 1 I I B 1 1 M M A 1 D 1 a: b: c: 10mm D I M I M I M I M 1 Finished front edge 1 1 I I I A A B B

a: Place 3 runners on the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw . b: Slide the runner back the other way and fit the 2nd screw into the corresponding hole in the right side . c: Screw 2 metal dowels into the right side . Insert 2 large locking nuts into the right side . Tap 2 wooden dowels into the right side . 2 I I B 2 2 M M A 2 a: b: c: D 2 I M I M I M I M I I I A A B B 2 2 2 Finished front edge Finished front edge Finished front edge

Insert 2 large locking nuts into each of 2 the rails . Tap 2 wooden dowels into each of 2 the rails . B 4 D 4 4 A B Fit the the 2 rails to the right side Push the 2 rails onto the right side . Use a screwdriver to tighten the large locking nut fitted to each of the rails . Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn. 2 4 B B 4 Step 11 Fit the left side Push the left side onto the rails . Use a screwdriver to tighten the large locking nut fitted to each of the rails . 4 1 B 4 Step 12 Note: Support this rail until the left side has been fitted in the next step. 4 4 2 4 1 4 Finished front edge

Screw 4 metal dowels into the top . A 3 A A A A Finished front edge 3 Fit the top Push the top onto the assembly. Use a screwdriver to tighten the 2 large locking nuts fitted to each of the sides and . . 3 B 1 2 Step 14 1 2 3 Step 15 Fit the 4 plastic nails Tap 2 plastic nails into the bottom edge of each of the sides and . . J 1 2 J J J J 1 2

a: Square up the unit by making sure that measurement x to x equals y to y. b: Place the back onto the unit. Nail around the outside edges of the back . Note: Nails should be spaced about 150mm apart. Stand the unit up for the next step. 10 E The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y a: 10 10

or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 11 ALR3197 Step 17 Fit the drawers Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners . Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner. Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly. Assembly is complete H M M H 2nd threaded hole M H 6 7 H H 6 7

or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Important - Please read these instructions fully before starting assembly Dimensions Width - 75.1cm Depth - 39.6cm Height - 90.1cm Sparkle - 5 Drawer Chest Assembly Instructions - Please keep for future reference Issue 2 - 02/10/15 412/1961 402/3124 395/7655

Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 31kgs. Please lift with care. • Check you have all the components and tools listed on pages 1, 2 and 3. • Remove all fittings from the plastic bags and separate them into their groups. • Keep children and animals away from the work area, small parts could choke if swallowed. • Parts of the assembly will be easier with 2 people. • Make sure you have enough space to layout the parts before starting. • Do not stand or put weight on the product, this could cause damage. • Assemble the item as close to its final position (in the same room) as possible. • Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton). 1 Care and maintenance • Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. • From time to time check that there are no loose screws on this unit. • This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference. • We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. • Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice. • Dispose of all packaging carefully and responsibly. Tools required Rule Scissors Hammer Eye protection (when using a hammer or drill) Cross-head screwdriver Electric drill (only use when drilling into walls)

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below When applicable, remove any protective film before use 2 1 2 3 5 6 Left Drawer Side (W370-124LH) (37 x 12.4cm) x 5 Right Drawer Side (W370-124RH) (37 x 12.4cm) x 5 7 4 8 9 10 Left Side (DF3867) (88.6 x 37.2cm) Rail (DF3813) (71.7 x 6cm) x 3 Right Side (DF3868) (88.6 x 37.2cm) Top (DF3812) (75.1 x 39.6cm) Drawer Front (DF3814) (73.7 x 16.2cm) x 5 Drawer Back (W684-124) (68.4 x 12.4cm) x 5 Drawer Base (T695-367) (69.5 x 36.7cm) x 5 Back (X861-743) (86.1 x 74.3cm)

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 3 Ruler - Use this ruler to help correctly identify the screws mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 A B D E F G H I L Small locking nut (F3) x 10 C Nail (F51) x 25 M J 9mm Screw (F74) x 10 K 9mm Screw (F73) x 20 Drawer runner (F1004) x 10 Knock-in Peg (F171GY) x 20 Large locking nut (F900) x 10 Metal dowel (F901) x 20 Wooden dowel (F22) x 10 Wedgefix (F639) x 20 25mm Screw (F50) x 15 Plastic Nail (F91) x 4 Handle (F569) x 5 N Strap Screw Washer x 2 Overbalance protector kit (F269) x 1

fronts Screw 2 metal dowels into each of the drawer fronts . Note: Tighten the metal dowels up fully against the panels. A 5 Prepare the drawer sides Insert a small locking nut into the hole shown on the left drawer side and the right drawer side . Note: The arrow on the locking nut must point towards the hole in the edge of the panel. Step 3 C 6 7 Attach the drawer sides to the drawer fronts Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts . Turn the small locking nuts on the left drawer side and right drawer side . Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn. 6 7 5 C C 6 7 6 7 A A 5

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front . Step 5 Fit the drawer back Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back . Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and . Step 6 9 6 7 5 8 6 7 9 8 8 F Attach the handles Attach a handle to each of the drawer fronts . using screws . Note: Do not overtighten the screws. L G 5 6 7 Step 7 Fit the wedgefixes Turn the 5 drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws. K x 5 x 5 x 5 F F x 5 K K K K K 9 6 8 6 7 9 7 G G G L 5

a: Place 5 runners on the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw . b: Slide the runner back the other way and fit the 2nd screw into the corresponding hole in the left side . c: Screw 3 metal dowels into the left side . Insert 2 large locking nuts into the left side . . Note: The arrow on the locking nuts must point towards the hole in the edge of the panel. Tap 2 wooden dowels into the left side . Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels. B 1 I I B 1 1 M M A 1 D 1 a: b: c: 10mm D I M I M I M I M I M I M I I I I I A A A B B 1 1 1

a: Place 5 runners on the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw . b: Slide the runner back the other way and fit the 2nd screw into the corresponding hole in the right side . c: Screw 3 metal dowels into the right side . Insert 2 large locking nuts into the right side . Tap 2 wooden dowels into the right side . 2 I I I M B 2 2 M M A 2 a: b: c: D 2 I M I M I M I M I M Finished front edge 2 Finished front edge 2 Finished front edge 2 I I I I I A A A B B

Insert 2 large locking nuts into each of 3 the rails . Tap 2 wooden dowels into each of 3 the rails . B 4 D 4 A B Fit the the 3 rails to the right side Push the 3 rails onto the right side . Use a screwdriver to tighten the large locking nut fitted to each of the rails . Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn. 2 4 B B 4 Step 11 Fit the left side Push the left side onto the rails . Use a screwdriver to tighten the large locking nut fitted to each of the rails . 4 1 B 4 Step 12 B B D 4 Note: Support these 2 rails until the left side has been fitted in the next step. 4 4 4 2 4 4 4 1

Screw 4 metal dowels into the top . A 3 Fit the top Push the top onto the assembly. Use a screwdriver to tighten the 2 large locking nuts fitted to each of the sides and . . 3 B 1 2 Step 14 Step 15 Fit the 4 plastic nails Tap 2 plastic nails into the bottom edge of each of the sides and . . J 1 2 A A A A Finished front edge 3 3 1 2 J J J J 1 2

a: Square up the unit by making sure that measurement x to x equals y to y. b: Place the back onto the unit. Nail around the outside edges of the back . Note: Nails should be spaced about 150mm apart. Carefully stand the unit up for the next step. 10 E The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y a: 10 x E 10 Warning: The unit is heavy. Lift with care. Fit the drawers Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners . Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner. Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly. H M M H 2nd threaded hole M H 6 7 H H 6 7

or email: [email protected] (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 11 ALR3198 Step 18 Fit the overbalance protector kit To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . to the unit, or an alternative fixing method of your choice. Wall fixings are not supplied as they will need to suit the wall type. Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert. Assembly is complete N Attach the strap to the unit Attach the strap to the wall Wall fixing (not supplied) Washer Strap Strap N N Example Screw (not supplied) Washer Screw UNIT