SoundGate VIDVWTRG1V4 Installation Instructions

signals (DVD, VCR, rearview camera, game console, etc.) to the factory navigation systems in the Volkswagen Touareg. Note: The VIDVWTRG1V4 also provides one stereo audio input. Features... The VIDVWTRG1V4 utilizes microprocessor control, ultra-reliable surface-mount construction, and advanced firmware design, to flawlessly match the video signal from the new sources to the factory system. The VIDVWTRG1V4 is also equipped with brightness, color, contrast and tint adjustments to allow you to get the best quality picture possible. Copyright© 2004-2007 SoundGate®. All Rights Reserved. SoundGate® is a registered trademark of Stillwater Designs, Inc. All other trademarks are the property of their respective owners. Rev20070827 Be Sure To Ask Your Autosound Specialist About These Other Exciting SoundGate Products... • Competition-Grade Interfaces for adding amplifiers • Remote audio control interfaces that let you control aftermarket receivers and CD players from your factory rear seat, or steering-wheel-mounted audio controls. • And many others! www.soundgate.com Why SoundGate Dealers have the edge... The technologies used in today’s vehicles are as sophisticated as any laptop computer. At SoundGate we believe these new technologies are full of opportunities for mobile electronic dealers across the nation. We make it a high priority to not only research these new systems, but to understand them and their impact on the aftermarket car audio industry. Armed with this knowledge, we are well equipped to help you integrate new components into these systems with our innovative, high-performance interfaces and unparalleled technical support. VIDVWTRG1V4 The SoundGate VIDVWTRG1V4 works in the following Volkswagen vehicles, when equipped with factory navigation: 2003-06 Touareg If you experience any problems, call SoundGate Technical Support at 800-256-0808 or e-mail us at [email protected] Liability Disclaimer: SoundGate®, Stillwater Designs, Inc., its subsidiaries, or Officers of the corporation cannot be held liable for damages or injuries caused by, or resulting from the use of this instruction guide or product. REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY OF THE PURCHASER. ANY IMPLIED WARRANTY ON THIS PRODUCT INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE DURATION OF THE WARRANTY(please see the enclosed Limited Warranty document for complete Warranty information). SOUNDGATE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE AND USE OF THIS PRODUCT. SOUNDGATE PROHIBITS ANY RETAILER FROM EXTENDING ANY WARRANTY OR WARRANTIES ON BEHALF OF SOUNDGATE TO ANY PERSON. SOUNDGATE IS NOT RESPONSIBLE FOR ANY INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Strictly adhere to all car manufacturer warnings that pertain to the disassembly, maintenance, or servicing of the vehicle and any of its associated parts or systems. SoundGate cannot be held responsible for discrepancies, or inconsistencies that may occur due to vehicle manufacturing changes. If you feel that you cannot agree with the above limitations, please return this product to the dealer you purchased it from, or call SoundGate Customer service at 800-256-0808 for a Return Authorization number, and return the product to SoundGate for a credit or refund. Page 1 Simple-fi TM Simple-fi TM

A. You will be connecting the SoundGate VIDVWTRG1V4 at the factory navigation radio. Gain access to this location. B. Press the locking tab on the black housing adjacent to the black locking arm, and rotate the locking arm 90°. Insert connector into port on rear of radio and rotate locking arm back to lock connector in position. C. Plug the white 16-pin molex-style connector into the video module. Preliminary: A. Please consult a factory service manual for exact location and disassembly instructions if you are unsure of the procedure. Pay close attention to any warnings or instructions regarding working in or around airbags. B. Turn the ignition key to the “Off” position. C. Make sure the car’s factory radio is turned to the “Off” position. Step 3 Install the video source unit(s) Referencing the instructions provided with your video source units, install the components in the desired locations. Route the video cables and any required power, ground, and trigger wires to the factory amplifier location for connection to the VIDVWTRG1V4. Step 2 Connect audio RCA’s from video source If applicable, connect the audio RCA’s from your video source to the RCA’s on the VIDVWTRG1V4 cable. Step 4 Verify DIP switch settings on VIDVWTRG1V4 module On the end of the module as shown in the photo at lower left, you will see a red 5-position DIP switch. Verify that the switches are set as follows (On = down, Off = up): 2, 3 = on (down) 1, 4 and 5 = off (up) Step 1 VVIIDDVVW WTTRRGG11VV44 IINNSSTTAALLLLAATTIIOONN IINNSSTTRRUUCCTTIIOONNSS Connect remaining wires Referencing Figure 2 and 3 on page 3, connect the remaining wires on the VIDVWTRG1V4 harness. One of the options shown will cover most installations. Consult the documentation that came with your video component to determine which of these is appropriate for your installation. Step 5 Page 2 IMPORTANT WARNING! It is illegal in all 50 U.S. states, and in most Canadian provinces, to have real time video (TV broadcast, VHS, DVD video, etc.) in view of the driver. IF YOU ARE GOING TO USE THE SOUNDGATE VIDEO INTERFACE FOR ANYTHING OTHER THAN INTERFACING A REARVIEW CAMERA SYSTEM, THE BLUE INTERLOCK WIRE ON THE SOUNDGATE VIDEO MODULE MUST BE PROPERLY CONNECTED TO PREVENT THE DRIVER VIEWING REAL TIME VIDEO WHILE THE VEHICLE IS IN MOTION. We do not want to put our dealers in a position of liability, nor our customers in danger in the event of an accident due to driver distraction. If you do not intend to comply with applicable law, please return the SoundGate video module to the dealer it was purchased from, or to SoundGate if it was purchased direct. Call SoundGate Customer Service at 800-256-0808 for a Return Authorization. DIP switches Inputs and Controls Video Input 2 iPod Input Video Input 1 Brightness/Color/Contrast /Tint Adjustments Inputs and Controls

the camera video signal connected to Video 1, with the grey Source 1 trigger wire fed from the back up light circuit, when you put the vehicle in reverse, the VIDVWTRG1V4 will automatically switch the screen display to the rearview camera. Adjusting picture quality: VIDVWTRG1V4 module is equipped with brightness, color and contrast adjustments. Note: Adjustments affect both Video 1 and 2 equally (cannot be set individually). VVIIDDVVW WTTRRGG11VV44 OOPPEERRAATTIIOONN 30 86 85 87a 87 +12 Volt ACC “trigger” from Source 2 (if present) Bosch Relay (not included) Ground Ground Ground “trigger” from Source 2 (if present) Black - trigger wire to activare Source 2 White 7-pin connector with single black wire Manual Latching-type single pole, single throw switch (not included) Chassis ground 30 86 85 87a 87 Ground “trigger” from Source 1 (if equipped) Bosch Relay (not included) +12 Volt ACC (switched) Manual Latching-type single pole, single throw switch (not included) +12 Volt from back up light circuit (hot when vehicle is in reverse) OR +12 Volt “trigger” from Source 1 (if equipped) White 16-pin connector Red Black Blue +12 Volt ACC (switched) Chassis Ground Interlock - ground from hand brake (video interlock) Grey trigger wire to activate Source 1 +12 Volt ACC (switched) Figure 3 - Source 2 Activation Wiring Figure 2 - Source 1 Activation, Power, and Ground Wiring VVIIDDVVW WTTRRGG11VV44 IINNSSTTAALLLLAATTIIOONN IINNSSTTRRUUCCTTIIOONNSS Page 3 Finish installation Once testing is done and the system is functioning properly, reinstall the all trim panels removed during installation. Installation is complete! Step 6 Reinstall radio and test operation A. If you have installed a rearview camera, start the vehicle, turn on the radio and navigation system and put the vehicle in reverse. The navigation display should change to show the view from the camera. Shifting the vehicle out of park should return you to the navigation display. If necessary, adjust the brightness, color and contrast with the controls on the VIDVWTRG1V4. B. If you have installed a video system, with the vehicle in park gear, and the parking brake on, activate the video source. The navigation display will change to show the video source. C. With the video source active and playing, test the video interlock by taking off the parking brake. The navigation display should return. Step 5