Prorack VOYAGER TRAY Manual 

1033885B PR3102 Rev2 (1x) (2x) (3x) (3x) (3x) (11x) (4x) (4x) (4x) (4x) (4x) (4x) RECOMMENDED TOOLS: Phillips screwdriver Tapemeasure or ruler With a crossbar spread of 24-29” (61cm-74cm), you may carry bikes, skis, or kayaks, provided you do not exceed the recommended weight limit for your vehicle. • To determine the crossbar spread on your rack, measure between the crossbars. Carry gear in the basket, and attach accessories directly to the Voyager (using accessory instructions). VOYAGER TRAY

IF YOU HAVE BARS THAT CAN BE MOVED… Move the bars to 30” (76cm) apart. LOAD BASKET ONTO RACKS. Center basket over your rack’s crossbars. DO NOT ATTACH BRACKETS TO UNSTABLE POINTS. Do not attach brackets at these locations. •IF YOU HAVE FIXED BARS: •IF YOUR BARS MOVE: (SIDE VIEW) A friend would make this easier . TIGHTEN YOUR CROSSBARS IF YOU LOOSENED THEM. BARS THAT CANNOT MOVE… Continue to STEP . ATTACH FAIRING TO EITHER END OF BASKET. Pry open the SnapArounds, attach them to the LOWER FRONT BAR. • Insert bolts through washers, fairing and SnapArounds. • Attach knobs and TIGHTEN. NOTE: The fairing can fold down when carrying long slender loads. Remove the machine screws from the ends of the Voyager tubes. NOTE: Always replace machine screws with washers (from Voyager) into same holes when reassembling. Insert screws with washers into each of the joints and tighten them. ASSEMBLE THE BASKET.

ATTACH THE KNOBS: Engage the threads of the bolts. CHECK INSTALLATION: Make sure installation is secure by tugging at basket. On some vehicles, hatch interference is unavoidable. TO REMOVE THE BASKET, DO NOT DISASSEMBLE THE HARDWARE. • Loosen the knobs until barely attached. • Unlock the T-bolts and let curved brackets swing freely. • Remove basket. USE CAUTION WHEN OPENING YOUR HATCH. T-BOLT IS LOCKED when the “T” of the bolt is turned inside the hole: TIGHTEN THE KNOBS EVENLY. SECURE THE BASKET TO THE BARS­. Lock the T-Bolts. POSITION THE SUPPORT BRACKETS ABOVE YOUR VEHICLE’S CROSSBARS. • Place the brackets OUTSIDE of the basket frame. • Tabs on brackets must face INBOARD. It may be necessary to move the bracket to a new position, or to adjust the basket position. KEEP BAR BELOW TAB! POSITION THE COVER BRACKETS. Position cover bracket onto installed support brackets. Hooked tab should cover the larger support bar. Arrow points inboard to center of vehicle. ATTACH BOLTS. Insert bolt into round hole, and T-bolt into slotted hole. The basket should NOT SLIDE on the bars. Tighten knobs if necessary. •CONTINUE TO BACK PAGE FOR IMPORTANT LOAD LIMITATIONS...

DO NOT EXCEED BASKET CONTENT WEIGHT LIMIT: 140 LBS. (63 KG) LOAD LIMITS: ▲ 25 lbs. (11 kg) ▲ basket contents DO NOT EXCEED YOUR RACK’S weight limit! Always tie down long loads at front and rear. RECHECK ALL FASTENERS AFTER A LOAD HAS BEEN APPLIED. CHECK REGULARLY ON LONG JOURNEYS DISTRIBUTE YOUR LOAD EVENLY INSIDE THE BASKET.

Yakima Australia Pty Ltd ABN 58 154 440 221 17 Hinkler Court, Brendale QLD 4500 Tel: 0800 4776 722 (NZ) or 1800 143 548 (AU) Email: [email protected] or [email protected] 1. Where the product is supplied to the customer for other than business purposes within the meaning of section 43 of the New Zealand Consumer Guarantees Act 1993, the provisions of that Act shall apply. It is important that anyone who fits or uses this product does so in accordance with the manufacturer’s instructions. 2. Where the product is supplied to the customer for business purposes within the meaning of section 43 of the New Zealand Consumer Guarantees Act 1993, the provisions of that Act and all other representations or terms (including any conditions or warranty expressed or implied by law, statute or otherwise) not expressly included in this leaflet are hereby expressly excluded shall have no effect and the clauses (a) and (b) shall apply. 3. Subject to the Additional Information (Australia), where the product is supplied and purchased in Australia, the following shall apply: (a). THE SUPPLIER WARRANTS the product to be free from defects in materials and/or workmanship for a period of three (3) years from the date of original purchase (the warranty period). Proof of purchase is required. Subject to the limitations and exclusions set out below, the Supplier hereby agrees to remedy any defects in materials or workmanship becoming apparent during the warranty period, by replacing or repairing any defective product or component (at its option) free of charge to the purchaser in respect of replacement parts or labour. Any defective product or component must be notified and where practicable, returned at the purchaser’s expense to the Supplier immediately upon discovery of the alleged defect and no attempt made on the part of the purchaser to repair it. (b). EXCEPTIONS, EXCLUSIONS AND LIMITATIONS TO WARRANTY. The product and/or its components must be fitted/assembled and loaded in accordance with the Supplier’s written instructions and any requirements set out in the car’s owner manual. This warranty does not cover defects, loss or damage resulting from circumstances beyond the Supplier’s control including, but not limited to misuse, overloading, or failure to assemble and/or fit the product or component in accordance with the Supplier’s written instructions. Nor does the warranty cover defects, loss or damage resulting from accidents, unlawful use of the vehicle or defects/inconsistencies in the vehicle on which the product or component is fitted. Liability for direct, indirect, special, punitive, incidental, exemplary, contractual or consequential damage or loss arising from defects, faulty materials or design omissions or negligence or workmanship in the product or its components is hereby expressly excluded subject to the following. Certain Commonwealth legislation, including the Competition and Consumer Act 2010 (Cth), and other State and Territorial legislation confers upon purchasers rights which cannot be excluded from or be restricted or modified by contract. Any conditions, guarantees and/or warranties implied by law and incapable of exclusion are deemed to be expressly incorporated herein. Nothing herein contained is intended nor shall be permitted to be inconsistent with any such conditions, guarantees and/or warranties. To the extent permitted by legislation all conditions, guarantees and/or warranties such as implied warranties which are capable of exclusion are hereby expressly excluded and negatived. ADDITIONAL INFORMATION ( AUSTRALIA ) This information should be read in conjunction with clauses (a) and (b). IMPORTANT LEGAL NOTICE Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty does not change or take away your rights under the Australian Consumer Law. Your right to claim under this policy for the benefits covered is in addition to other rights and remedies you have under the law in relation to the product. Where you become aware of defects in materials or of workmanship, and wish to make a claim under this warranty you must do the following for the warranty to be honoured by your Prorack dealer or Yakima Australia Pty Ltd ABN 58 154 440 221 (Yakima): 1. Make a claim as soon as practicable by contacting the Prorack dealer from whom you purchased the product, who will give you instructions on how to proceed. 2. If you are unable to contact the Prorack dealer, or the dealer is not able to remedy the defect, you should contact Yakima as soon as practicable at: Call: 0800 4776 722 (NZ) or 1800 143 548 (AU) Email: [email protected] or [email protected] Alternately, you can write to Yakima at 17 Hinkler Court, Brendale QLD Australia 4500 in order to make a claim under your warranty. 3. Upon contacting Yakima directly, you should explain as fully as possible the defect. A Yakima representative will provide you with appropriate instructions for returning the product together with a copy of the original purchase invoice or receipt to Yakima. 4. The costs and expenses associated with making a claim under your warranty including the costs of complying with those instructions and of returning the product to Yakima or the Prorack dealer will be borne by you. Following receipt of the product and purchase invoice or receipt, Yakima or the Prorack dealer must inspect the product to determine whether the claim falls within the warranty. If: 4.1 the claim falls within the warranty, Yakima will remedy any defects in materials or workmanship becoming apparent during the warranty period, by replacing or repairing any defective product or component (at its option) free of charge to the purchaser in respect of replacement parts or labour. 4.2 the claim does not fall within the warranty, Yakima will return the product to you at your expense. WARRANTY & DISCLAIMER