Datalogic DS8100A-3002 Quick Reference Manual

2 DS8100A-3002 General View: Figure A Laser Beam Output Window 1 Figure B Programming Keypad 1 Phase On LED (Yellow) 3 Power On LED (Green) 2 TX Data LED (Green) 5 Network LED (Red) 6 Encoder LED (Yellow) 4 LCD Display 7 Figure C Lonworks 17-pin Male Connector 1 Lonworks 17-pin Female Connector 2 NOTE For further details on product installation, see the complete Reference Manual available on the configuration CD-ROM included with this product. 1 1 2 7 1 2 3 4 5 6

3 Technical Features: ELECTRICAL FEATURES Supply Voltage 20 - 30 Vdc Power Consumption 1.0 to 0.67 A; 20 W typical 1.5 to 1.0 A; 30 W Max. (including startup current) Communication Interfaces Auxiliary Baud Rate RS232 1200 to 115200 Other Lonworks 1.25 Mb/s OPTICAL FEATURES Light Receiver Avalanche photodiode Safety Class 630 to 680 nm Wavelength Class 2-EN 60825-1; Class II-CDRH Laser Control Security system to turn laser off in case of motor slow down READING FEATURES Scan Rate ≤ 1000 scans/s Max. Resolution Max. Read. Distance Max. Read. Width Max. Depth of Field (see reading diagrams) USER INTERFACE LCD Display 2 lines by 20 characters LCD Keypad 3 keys LED Indicators Power ON (green) Phase ON (yellow) Encoder (yellow) TX Data (green) Network (red) SOFTWARE FEATURES Operating Modes PackTrack™ Config. Mode Genius™ utility program Parameter Storage Non-volatile internal FLASH Readable Codes Interleaved 2/5 Code 39 standard Codabar Code 128 EAN 128 Code 93 (standard & full ASCII) EAN/UPC Code Selection Up to 10 codes during one reading phase ENVIRONMENTAL FEATURES Operating Temperature 0° to +50 °C (+32 to +122 °F) Storage Temperature 20° to +70 °C (-4° to +158 °F) Humidity -90% non condensing Vibration Resistance: EN 60068-2-6 14 mm @ 2 to 10 Hz; 1.5 mm @ 13 to 55 Hz 2 g @ 70 to 200 Hz; 2 hours on each axis Shock Resistance: EN 60068-2-27 30 g; 11 ms 3 shocks on each axis Protection Class EN 60529 IP65* PHYSICAL FEATURES Dimensions mm (inch) 217 x 173 x 127 (8.54 x 6.79 x 4.98) Weight 5 Kg (11 lbs.) * IP65 cables and connectors required (CAB-850x or BTK-8500).

4 Accessories: NAME Description Part Number PWO-480 Power and Connect System 480W 93ACC1767 FS-1 Frame Shaper (8 pcs) 93ACC1750 FBK-8100 Fast Bracket Kit (2 pcs) 93ACC1130 US-8100 Bracket Kit (10 pcs) 93ACC1140 GFC-80 90 Degree Mirror 93A251020 GFC-800 90 Degree Close Distance Mirror 93A201103 S30 Photocell Kit 93ACC1782 PH-1 Photocell Kit - PNP 93ACC1791 MEP-543 Photocell Kit - NPN 93ACC1728 OEK-2 Optical Encoder Kit (10 m cable + spring) 93ACC1770 OEK-1 Optical Encoder Kit + 10 m cable 93ACC1600 BTK-8100 Bus Terminator Kit (5 pcs) 93ACC1090 BTK-8500 IP65 Terminator Kit (2 pcs) 93A051286 PLL-8000 Optocoupled PLL device 93ACC1280 CAB-8100 10 wire shielded cable D 9.5 mm – 50 m 93ACC1120 CAB-8101 17-pin scanner/scanner connection cable 1.2 m 93A051020 CAB-8102 17-pin scanner/scanner connection cable 2.5 m 93A051030 CAB-8105 17-pin scanner/scanner connection cable 5 m 93A051040 CAB-8501 IP65 Cable Fam 8K 1,2 m 93A051283 CAB-8502 IP65 Cable Fam 8K 2,5 m 93A051284 CAB-8505 IP65 Cable Fam 8K 5 m 93A051285 Datalogic WebSentinel-005 Supervisor (up to 5 arrays) 93A101014 Datalogic WebSentinel-010 Supervisor (up to 10 arrays) 93A101015 Datalogic WebSentinel-020 Supervisor (up to 20 arrays) 93A101016 Datalogic WebSentinel-032 Supervisor (up to 32 arrays) 93A101017 Datalogic WebSentinel-064 Supervisor (up to 64 arrays) 93A101018 Datalogic WebSentinel-128 Supervisor (up to 128 arrays) 93A101019 Datalogic WebSentinel-256 Supervisor (up to 256 arrays) 93A101020 Electrical Connections: Two 17-pin connectors provide access to the scanner’s local Lonworks network used for both input and output connections to build a multi-sided or omni-station system. 17-pin Lonworks Connector Pinout Pin Name Function A1 GND Supply voltage (negative pin) A2 VS Supply voltage 20 to 30 Vdc (positive pin) Cable shield A - internally connected by 1 CHASSIS capacitor to chassis 2 n.c. Not connected Cable shield B - internally connected by 3 CHASSIS capacitor to chassis 4 TXAUX Transmit data of auxiliary RS232 (referred to SGND) 5 SGND Signal ground (connected to GND) 6 RXAUX Receive data of auxiliary RS232 (referred to SGND) 7 VS_I/O Supply voltage of I/O circuit 8 Lon A+ Lonworks a line (positive pin) 9 Lon A- Lonworks a line (negative pin) 10 Lon B+ Lonworks b line (positive pin) 11 Lon B- Lonworks b line (negative pin) 12 SYS_I/O System signal 13 SYS_ENC_I/O System signal 14 Reserved Internally connected 15 Ref_I/O Reference voltage of I/O circuit A1 A2 1 15 Female - Output A1 A2 1 15 Male - Input 17-pin Local Lonworks Connectors

5 Connectivity: DS8100A-3002 Typical Layout Conveyor SC6000 Extended I/O Host HUB ETHERNET SC6000 AUX CAB-SC6003 CAB-SC6013 Power/Net VAC INPUT CAB-SC6103 Cable PWO LONWORKS ENCODER PS PS Aux CAB-850x CAB-850x CAB-850x CAB-850x CAB-850x up to 3 scanners per branch BTK8500 Bus Return DX8200A-3002 DS8100A-3002 CAB-850x up to 4 scanners per branch BTK8500 Bus Return DX8200A-3002 DX8200A-3002 DS8100A-3002 DS8100A-3002 DS8100A-3002 CAB-850x

6 Example of Redundant System Layout AUX CAB-SC6103 Extended I/O ETHERNET SC6000 CAB-SC6003 CAB-SC6013 Power/Net VAC INPUT PWO LONWORKS ENCODER PS PS Aux CAB-850x CAB-850x BTK8500 CAB-850x CAB-850x CAB-850x Extended I/O ETHERNET SC6000 CAB-SC6003 CAB-SC6013 Power/Net VAC INPUT PWO CAB-PWO 03 Redundancy CAB-850x CAB-850x CAB-850x BTK8500 DX8200A-3002 ENCODER PS PS Aux LONWORKS Working Controller Protecting Controller to Host to Host DX8200A-3002 DX8200A-3002 DX8200A-3002 DS8100A-3002 DS8100A-3002 DS8100A-3002 DS8100A-3002

8 Mechanical Installation: DS8100A-3002 can be installed to operate in any position. There are 16 screw holes (M6 X 8) on the sides of the scanner for mounting. The following diagrams give the overall dimensions of the reader standard model and mounting bracket. They may be used for their installation: 127 [4.98] 173 [6.79] 217 [8.54] 50 [1.97] 68 [2.66] 45° 47 [1.84] 45° 50 [1.97] 47 [1.84] 68 [2.66] M6 N°16 mm inch 164 [6.45] [0.19] 5 100 [3.93] 30 [1.18] 16 [0.63] 100 [0.59] R 15 [1.88] 48 [0.59] R 15 N°4 [3.93] 15 [0.59] 164 [6.45] 80 [3.15] 45 [1.77] 17.5 [0.68] 8.5 N°4 [0.33] DS8100A-3002 Overall Dimensions ST-163 Mounting Bracket Overall Dimensions WARNING When installing several scanners, take care to position them correctly so that no laser beam enters the reading window perpendicularly and at the same level of the output beam of the other scanners. This condition could occur more frequently for side mounted applications. If these precautions are not followed, it may occur that the laser of the blinded scanner starts blinking due to an internal circuit which temporarily turns the laser off when detecting a power anomaly. To resolve this problem, it is sufficient to slightly change the inclination and position of one of the two scanners involved. mm inch mm inch

9 Reading Diagrams: Note: (0,0) is the center of the laser beam output window. DS8100A-3002 – 0.50 mm/20 mils CONDITIONS Code = Interleaved 2/5 or Code 39 PCS = 0.90 “Pitch“ angle = 0° “Skew“ angle = 10° “Tilt“ angle = 0° (in) 0 15 32 (in) 24 40 0 40 60 (cm) 20 10 -10 0 (cm) 80 100 120 140 48 56 160 64 40 50 60 30 -40 -30 -20 -60 -50 12 8 0 4 20 24 16 -12 -8 -4 -20 -16 -24 Safety Precautions: Figure A Laser Safety Label 1 Warning and Device Class Label 2 Identification Label 3 The scanner is classified as a Class 2 laser product according to EN60825-1 regulations and as a Class II laser product according to CDRH regulations. Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to hazardous laser light. There is a safety device, which allows the laser to be switched on only if the motor is rotating above the threshold for its correct scanning speed. 1 2 3

10 The laser beam can be switched off through a software command (see also the Genius™ Help On-Line). AVOID EXPOSURE LASER LIGHT IS EMITTED FROM THIS APERTURE CAUTION-CLASS 3B LASER LIGHT WHEN OPEN AVOID EXPOSURE TO BEAM AVOID EXPOSURE LASER RADIATION IS EMITTED FROM THIS APERTURE Laser Safety Label LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAXIMUM OUTPUT RADIATION 1 mW EMITTED WAVELENGTH 630~680 nm TO EN 60825-1:2001 Model No. Amp. Serial No. DATALOGIC S.P.A. Via Candini, 2 40012 Calderara di Reno - Bologna - Italy Manufactured Volt This product conforms to the applicable requirements of 21CFR1040 at the date of manufacture. Warning and Device Class Label Device Identification Label The laser diodes used in this device are classified as Class 3B laser products according to EN 60825-1 regulations and as Class IIIb laser products according to CDRH regulations. Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode (30 mW at 630~680 nm). Power Supply This product is intended to be installed by Qualified Personnel only. This scanner is intended to be supplied by either a UL Listed power supply marked 'Class 2' or 'LPS', output rated 20 - 30 V dc, minimum 1.5 A or by a UL Listed computer with LPS outputs. DS8100A-3002 must be supplied by a Class II Power Supply Unit conforming to the EN 60950 safety regulation. Patents: This product is covered by one or more of the following patents. U.S. patents: Re. 36,251; 5,483,051; 5,992,740; 6,177,979 B1; 6,347,740 B1; 6,394,352 B1; 6,443,360 B1; 6,527,184 B1; 6,629,639 B2; 6,688,524 B1; 6,742,710 B2; 7,161,685 B1; 5,028,772; 5,124,538; 5,466,921; 5,548,107; 6,206,289 B1; 6,669,091 B2; 7,000,838 B2. European patents: 652,530 B1; 789,315 B1; 851,376 B1; 926,615 B1; 959,426 B9; 1,363,228 B1. Japanese patents: 3,793,585; 4,033,958. Additional patents pending.

08 Datalogic Automation S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el DS8100A-XXXX Laser Scanner e tutti i suoi modelli and all its models et tous ses modèles und seine Modelle y todos sus modelos sono conformi alle Direttive del Consiglio Europeo sottoelencate: are in conformity with the requirements of the European Council Directives listed below: sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous: der nachstehend angeführten Direktiven des Europäischen Rats: cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente: 89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi and further amendments et ses successifs amendements und späteren Abänderungen y succesivas enmiendas 2006/95/EC Low Voltage Directive Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti. On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety. Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité des produits. Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit entsprechen. Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas de seguridad relativas al producto. Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti: This declaration is based upon compliance of the products to the following standards: Cette déclaration repose sur la conformité des produits aux normes suivantes: Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht: Esta declaración se basa en el cumplimiento de los productos con las siguientes normas: EN 55022 (Class A ITE), September 1998: INFORMATION TECHNOLOGY EQUIPMENT RADIO DISTURBANCE CHARACTERISTICS LIMITS AND METHODS OF MEASUREMENTS EN 61000-6-2, September 2005: ELECTROMAGNETIC COMPATIBILITY (EMC) PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS EN 60950-1, December 2001: EN 60950-1/A11, April 2004: INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1 : GENERAL REQUIREMENTS EN 60825-1, March 1994: EN 60825-1/A1, July 1996: EN 60825-1/A2, March 2001: SAFETY OF LASER PRODUCTS - PART 1 : EQUIPMENT CLASSIFICATION, REQUIREMENTS AND USER'S GUIDE Lippo di Calderara, January 29th, 2008 Lorenzo Girotti Product & Process Quality Manager 821001262 (Rev. B)