Solax BUGGY PLUS Manual 

Text of the manual

Please read this Owner’s Manual before operating your scooter for the first time.

BUGGY PLUS Four-Wheel Outdoor Rear Wheel Drive Scooter Product images may vary and will be subject to real products received.

2.2 Technical Specifications-----------------------------------------------------5

3.Safety Guideline---------------------------------------------------------------------6 3.1 Safety Notices------------------------------------------------------------------6 3.2 EMI & RFI Information------------------------------------------------------12 3.3 Labeling Instruction---------------------------------------------------------13 4.Operation Instruction--------------------------------------------------------------14 5.Batteries & Charging--------------------------------------------------------------18 6.Operation Procedure--------------------------------------------------------------20 7.Driving Instruction------------------------------------------------------------------21 8.Maintenance, Repair and Storage--------------------------------------------22 9.Warranty Card----------------------------------------------------------------------25 Product images may vary and will be subject to real products received.

Thank you very much for choosing Solax electric scooter!

Please read this manual carefully before operating the scooter for the first time. This manual is applicable to the Four-Wheel Outdoor Rear Wheel Drive Scooter- Buggy Plus. If you do not understand all of the content completely or you need further assistance, please contact your scooter supplier: Dongguan Prestige Sporting Goods Company Limited. Calls to the following number are not free, Incase of emergency, you may contact dealers nearby for assistance. TEL: +86-0769-85922501 Company Email: [email protected] Do not modify your scooter in any way; doing so will void the warranty.

2. PRODUCT INTRODUCTION

2.1 Parts Handle Group Storage Bucket Front Signal Indictor Front Shroud Headlight Front Wheel Rear Shroud Tail Shroud Charging Port Gas Spring Switch Release Lever Rear Wheel Anti-Tip Wheel Rear Bumper Rear Signal Indicator Seat Assembly Control Panel Delta Handle

2.2 Technical Specifications

Model S5023 Weight Capacity 150kg Tyres 10inches of front wheel and rear wheel Speed 0-8 km/h Range Up To 30km Battery 12V/33Ah x 2pcs Charger 24V/5A Controller 24V/70A Motor 350W Brake System Electromagnetic Brake Drive System Rear Wheels Drive Weight (with battery) 77.5kg Weight(without battery) 57.5kg Turning Circle 1500mm Length 1215mm Wide 582mm Height 1160mm Handle Delta Ground Clearance Minimum 60mm Max. Climbing Angle 12° Color Red/Black; Blue/Black;White/Black Note: Final confirmation of the specifications, please subject to real products received.

3.1 Safety Notices

1. Please read this manual carefully before operating the scooter for the first time. 2. Please assess the personal health of the user before driving. The following conditions are not suitable for driving: sick or physically unwell and visually impaired, especially those with impaired upper limbs; those with acute cancer; those with heart disease; ;woman who is pregnant or in menstruation; children (under 12 years); Inconvenience or slowness of consciousness; patients who are unconscious, comatose, and have poor blood circulation or severely sensitive skin; consult a physician if they have concerns about their own health before using; consult a physician before using a heart rate adjuster. 3. Do not operate your scooter when you are tired, or after consuming alcohol. 4. Do not drive your scooter at night without proper lighting. 5. Always make sure the power is turned off when getting in and out of the scooter. 1.Failure to heed the warnings in this manual can result in personal injury. 2.Failure to pay attention to the precautions in this manual may result in damage to your electric scooter. 3.Do not turn on the power or try to drive the scooter while sitting unsteadily. 4.Please turn off the power when stop or leave to avoid danger of touching the starting lever by mistake. 5.Keep your center of gravity stable when riding in a vehicle. Avoid stretching or bending the body that loses equilibrium to cause a rollover or a fall of personnel. 6.This vehicle is suitable for single-person rides. It is strictly forbidden to carry two or more people to avoid accidents and dangers.

D A N G ER

FI G.4 FI G.5 FI G.6 7 S5023 OWNER’S MANUAL Don’t leave children playing alone nearby the mobility scooter. Do not operate your scooter after consuming alcohol. Do not use cell phone or any mobile device while riding the scooter. Make sure there is no obstacle behind while reversing scooter. No sharp turning or sudden stop while driving scooter. Never drive into traffic area.

Please read this manual carefully before operating the scooter for the first time.

Don’t attempt to drive on slopes more than 12 degrees. Do not leave hands and legs off improper location. No driving in snow or slippery area. Fasten seat belt and put your legs on foot plate. 1. Do not drive a scooter on public streets and highways. Please note that when you are sitting on a scooter, it is difficult for other vehicles to see you. Please follow local traffic rules and drive carefully in busy areas or shopping malls. 2. Always make sure the power is turned off when getting in and out of the scooter.

5. In some situations, user needs the presence of a trained companion to operate

the scooter. The trained companion can be a family member, or a care professional that specializes in assisting the daily life of the scooter user. Check with your doctor if you are using a drug that affects safe driving. 6. Please do not lift or move the scooter through the detachable parts of the body, for example, handrails, seats, and outer casings, otherwise the scooter will be damaged. 7. Please operate the scooter within the limits described in this manual. 8. Don't sit on a contemporary walker while on a moving vehicle. 9. When driving the scooter, keep your hands away from the wheels. Also note that loose clothing may also get caught in the tires. 10. Please consult your physiotherapist if you are using prescription drugs or if you have specific physiological limitations. Because some drugs and limitations may prevent you from operating the scooter safely. 11. Please note whether the driving mode is on. 12. If the scooter has an anti-roll device, please do not remove it. 13. Contact may result in electric shock and do not allow wiring on the A C /A D converter or charger. 14. Please do not lift or move the scooter through the detachable parts of the body, for example, handrails, seats, and shells. 3. Make sure scooter in good condition before driving. Do not suddenly turn off power switch while the scooter is running. 4. Failure to note the warnings in this manual may cause personal injury. If you are unable to understand this manual, please contact our local dealer, or technician for assistance.

Solax designed the scooter to maximize its use. Therefore, please do not modify,

add, remove or disable any parts of the scooter. Otherwise, it will cause some damage and loss. 1. Do not modify, remove, disable, or add any parts, features, or functions on your scooter. 2. Users need to fully understand the performance and endurance of this scooter. Solax recommends a safety check on the scooter before using. 18. When you make a sharp turn, please slow down and stabilize your center of gravity. Please do not make sharp turns when driving at high speed. 19. It can have an impact on the circuitry when driving in the rain, in the snow, in the fog, on the ice, or on a smooth surface. 20. When the scooter is on the elevator or other lifting products, please do not sit on the scooter. This scooter has not been designed for this purpose, and Solax is not responsible for any damage or loss. 21. Do not touch the motor after driving to avoid burns. 15. When going uphill, please do not make the direction of the scooter to form an angle with the slope. Please drive straight along the slope to prevent dumping or overturning. 16. Please do not climb the slope above the maximum climbing height. 17. Please do not reverse on the steps, road edges or other obstacles, otherwise it will cause rollover or dumping. Do not modify your scooter in any way; doing so will void the warranty.

Safety Check Before Operating The Scooter

1. Electrical Connections – secure and free from corrosion. 2. Freewheel Levers – engaged in drive position. 3. Batteries – fully charged and free from corrosion. Weight Capacity 1. The scooter has a Maximum weight capability that should never be exceeded; please refer to Chapter 2.2 Technical Specification. The maximum weight capacity includes the user and any accessories. 2. Exceeding the maximum weight capacity will void your warranty. Solax will not hold responsible for injuries damages resulting from failure to observe weight capacities. 3. Do not carry passengers on your scooter. Your scooter is designed and tested for one user to operate while seated. Operating Temperatures 1. Your scooter is designed to operate ideally between -25°C to 50°C. 2. In extremely cold conditions your batteries may freeze depending on the battery charge, usage, and composition of the batteries. In extremely hot conditions your scooter may operation at a lower speed. This is due to the safety mechanism built into the unit to prevent damage to the gearbox and other electronic functions when operating too hot.

EMI can be produced from different sources such as cellular phones, two-way

radios, radio station, television stations, amateur radio transmitters (HAM), wireless computer links, microwave signals, paging transmitters, and transceivers used by emergency vehicles. The EMI waves can cause unintentional movement of the scooter, or damage to the controller. Every electrical powered mobility device has a resistance to EMI. The higher the resistance levels the greater to protection. The intensity of the interference can be measured in volts per meter, V/M. EMI becomes more intense as you move closer to the source. The EMI produced from hand-held radios are of special concern. It is possible to unintentionally bring high levels of EMI very close to the scooter’s control system, effecting your movement and braking. The warnings listed below are recommended to prevent possible interference with the control system of your scooter. 1.Do not operate hand-held transceivers such as CB (citizens band) radios, or turn on personal communication devices, such as cellular phones, while the scooter is powered on. 2.Be aware of nearby transmitters, such as radio or television stations, and avoid close proximity. 3.If you experience unintended movement or brake release occurs, power off as soon as it is safe. Please report EMI incidents to local dealer. 4.be aware that adding accessories or components, or modifying the powered scooter, may make it more susceptible to interference from radio wave sources (Note: it is difficult to evaluate the effect on the overall immunity of the powered scooter). Please switch off power immediately under the following situations: 1. Unintentional scooter movements. 2. Unable to control direction. 3. Unexpected brake malfunction. 3.2 EMI & RFI Information Electromagnetic interference (EMI) tests have shown to produce adverse effects on the performance and control of electrically powered mobility devices.

Driving And Braking

1. Insert the key to turn on the key ignition. 2. Pull speed levers to forward and backward. 3. Right lever is for forward control whereas left lever for backward control (FIG 1). 4. Release the speed lever to stop scooter. 5. Adjust speed control button according to your preference. 6. Change the speed by pressing the "fast-slow" button only when scooter is stop. Headlight Speed Dial Horn Button Left Signal Indicator Battery Power Indicator Key Ignition Fast- Slow Switch Warning Light USB Charging Port Speed Lever Right Signal Indicator FIG.1 1.Electromagnetic brake will be activated automatically while speed exceed over 3O%of maximum speed. 2.The mobility scooter will move automatically while brake is disengaged. 3.Scooter will move freely when braking system disengaged.

Gas Spring Switch

Press Gas Spring Switch to adjust the angle for handle bar (FIG 2). When release gas spring handle, then handle bar will naturally be locked tightly. Do not adjust the angle of handle while driving the scooter. Scooter is never allowed to operate when the handle is not fixed and locked. Seat Adjustment The seat can be turned and fastened according to FIG 3. 1. The seat can be turned 360 degree and each stop for 45 degree. Press the lever upward, then turn the seat at 45 degree to fasten the seat.Attention--- Make sure the pin underneath lock in place with seat post. 2. Remove The Seat: press the release lever upward, then lift up the seat to remove the seat. 1. Never operate the scooter before seat fastened. 2. Be careful when adjusting the seat this may trap or pinch your fingers. FIG.2 FIG.3 Release Lever Gas Spring Switch

1.Power Indicator: Battery and charging indicator.

2.Speed Dial: tortoise means lower speed and rabbit means higher speed. 3.Head Light: press the switch to turn on the head light and press again to turn it off. 4.Left Signal Indicator: press the switch to turn on the left signal indicator, and press again to turn it off. 5.Right Direction Switch: press the switch to turn on the right signal indicator, and press again to turn it off. 6.Warning Light: front and rear signal indicators will flicker when press this switch. You can press this button when scooter needs to stop for a period of time or driving in foggy weather to prevent from accident. 7.Horn Button: the horn button can be pressed to give a warning to other persons. 8.Fast-slow Switch: rapid change in speed by pressing this button. FIG.4

The anti-tip wheels are designed to prevent from scooter overturn on slope.

USB Charging Port USB Charging Port can be charging for external electronic devices. Electromagnetic Brake Lever The scooter is equipped with Electromagnetic brake. Please do not switch off the brake whilst in operation. To move the scooter by hand you need to release the brake mechanism.(FIG.5) 1. Freewheel Mode: pull the brake lever upward to engage the brake. 2. Driving Mode: press the brake lever downward to release the brake. 1. Check the anti-tip wheels periodically. 2. Never remove anti-tip wheels without the assistance of technician. Electromagnetic Brake Lever Anti-Tip Wheel FIG.5 1.Exceeding the maximum weight capacity will cause damage of electromagnetic brake as well as personal injury. 2.Do not push mobility scooter when the scooter is in driving mode, otherwise it will cause damage of electromagnetic brake. 3.Never put the scooter in freewheel mode while on an incline. FIG.6

5.BATTERIES & CHARGING

Charging Your Scooter Turn off the power before charging. To charge your scooter, plug the charger into the scooter, and then into the electrical outlet. When the battery is fully charged remove the charger from the scooter. The location of the charging socket is shown on the FIG 7. The light on your charger indicate different charge statuses. In most cases your charger will show a red or orange light when charging, and a green light when the battery is more than 90% charged. If a green light is shown immediately upon connection then there may be a problem with the battery. Contact your dealer for more information. FIG.7 Charging Port 1.If you use your scooter on a daily basis, charge the battery as soon as you are finished with the day’s activities, and leave it on the charge until you are ready to use the following day. 2.If you use your scooter infrequently, charge the batteries once a week for 10-14 hours.

The product uses a maintenance-free sealed lead-acid battery without adding

water. There is no need to check the amount of battery liquid and add water. The battery must be fully charge prior to any trip. 1. Under normal circumstances, it takes 1-8 hours to charge the battery according to the power consumption. Beyond this time period, indicator light on the charger have change, please stop charging immediately and contact the designated repair station of the dealer of our company. 2. This product uses lead-acid batteries. Excessive discharge will affect the battery lifetime. 3. Charge your battery fully before you store it, and keep charge it once a month. 4. You should not dispose of electrical and electronic equipment and batteries together with your household waste, it shall be returned to the professional recycling department. 5. When the battery is not in use, it should be removed from the scooter and stored in a place where the sunlight cannot reach and the ventilation is good. 6. The performance of the battery is affected by environmental factors. Generally, when the temperature drops below 0 degrees Celsius, the battery power may be greatly reduced. When the temperature rises to about 20 degrees, battery function will return to normal naturally.

Dear users, thank you very much for your careful reading of the foregoing

structure and function of this scooter. Now we will elaborate on the operation procedures of this scooter: 1. If the scooter is newly purchased, please make sure that the scooter has fully charged. 2. Check whether the electromagnetic brake handle is in a closed. 3. Check whether the handle can be rotate flexible. 4. Adjust the angle between seats and handle and check whether the seat and the handle are fixed firmly before getting on the scooter. 5. Insert the key in to the ignition and switch the scooter on, the indicator light on the control panel will be light up. 6. Check the battery capacity display table to make sure that the remaining battery capacity can meet your travel requirements. 7. Move forward: make sure the scooter is on lowest speed, and then use your right hand to pull the right-side speed lever backward, the scooter will start to move forward. You can use the speed dial to adjust the speed; “Rabbit” means higher speed, “Turtle” means lower speed. 8. Reverse: use your left hand to pull the left-side speed lever backward then the scooter will start to move backward. Be aware of barriers when reversing the scooter.

9. Release speed lever the scooter will stop and lock the motor automatically.

10. Other functions of the control panel please refer to Chapter 4. Control Panel. 11. When parking or not using the scooter, please park the scooter in a safe position and pull out the key.Do not leave the key on the scooter. Do not operate your scooter when you are tired,or after consuming alcohol. Driving Instruction 1. Please do not drive the scooter if you cannot tell the condition of the surface. 2. Please do not drive the scooter into the loose gravel, soil and sand. 3. Please do not try to cross steps or gullies beyond the permitted scope of the scooter. 4. Please do not drive slopes beyond the permitted range of the scooter. 5. Please do not drive into traffic area.

8.MAINTENANCE, REPAIR AND STORAGE

Troubleshooting There are few parts of solax scooter which require maintenance. The following issues must be checked and maintained periodically: When the wheel chair is in trouble, please do the following check: Maintenance and Repair ①. Regularly check whether the screws and nuts of the scooter are loosening, especially the screws and nuts on the wheels (check every three months). ②. Check whether the handstand the shaft sleeve of the steel bowl is well fixed before driving. ③. Check whether the seat and armrest are fixed and stable. ④. Check regularly whether the electromagnetic brake meets the brake requirements of this scooter.For inspection, you can put the scooter on a slope that within permitted range to see if the scooter moving (check every three months). ⑤.Check the wear on the tire surface before driving, and replace the tire in time if the tire is damaged. ⑥.Check whether the emergency lights are running normally before driving. ITEM Cannot start Scooter suddenly slow down when driving INSPECTION Check if the key ignition is on off position Check if the brake levers is in driving mode Check if the battery is in low power Check if the battery is in low power SOLUTION Turn on the power switch Switch the brake levers to drive mode. Charge the battery Charge the battery

Periodically check all exposed screws or nuts for looseness.

Check all the wiring insulation condition, including the plug of the charger regularly. Daily Inspection Please check the following items before driving. If any abnormal phenomena are found, please contact the Solax or the local dealer to get help and solve it. Maintenance ①. In order to prevent the electrical components from damage, do not wash the scooter with a hose. The scooter should only be wiped using a damp cloth. ②. Do not exceed the permitted scope of the vehicle when driving. ③. The front and rear wheels need to be removed regularly and lubricated on the axle. ④. The motor scooter on brush shall be inspected and replaced regularly (every half year). ⑤. Protect all the electronic components from moisture, if some components become damp, please dry it before use. ITEM Control Panel Front and Rear Light Seat Motor Tyres Others INSPECTION 1.Check the function of the speed lever 2.Check the function of speed dial 3.Check the function of the horn 4.Check the function of the battery power indicator Check if the lights can work properly Check if the seat can be turn 360 in degrees Check if there are any unusual sounds

Basic Maintenance Instructions

Regular maintenance of the electric scooter can extend the service life of the scooter. 1.Seat: use clean cloth can wipe the appearance directly, or use clean wet cloth wring dry after wipe can. 2.Tires: use a clean cloth or soft brush to clean them directly, or use a clean wet cloth or a wet soft brush. Leave them to dry and clean. 3.Scooter Shell, Pedal, Handrail: use clean cloth can wipe exterior directly, or wring with clean wet cloth after wiping can. 4.Parking: please avoid parking the electric wheelchair in the place of sun exposure and rain or humidity for a long time; when parking the electric scooter, please make sure the power is off. 1.Never hose off your scooter or expose it to direct contact with water. 2.Never use any chemicals on the upholstery of your seat, this may cause the seat to dry out and crack. 1.Infrequently charged batteries, or batteries stored without a full charge are susceptible to permanent damage, causing unreliable performance from your scooter. 2.Improper storage of your scooter may result in permanent damage to the frame and electronics. Storage If you need to store your scooter, be sure it is stored in a dry place free from extreme temperatures. Always fully charge, and then disconnect the batteries prior to storage.

Solax- Four-Wheel Outdoor Rear Wheel Drive Scooter

Warranty Card User Name Address Model ID No Phone Number Serial Number Purchasing Date YY MM DD Warranty Periods Manufacturer Dealer (Stamp or Sign) Phone Number or Address 12 months warranty from purchase date, Battery is 6 month warranty Dongguan Prestige Sporting Goods Company Limited Warranty Statement: The dealer is responsible for the repair or replacement of the parts when quality problems with materials, manufacture or assembly develop under the normal usage.This does not affect your statutory rights. Warranty Exclusions: a.Damages caused by improper operation and maintenance; b.Damages caused by use of unauthorized spare parts; c.Damages caused by accidents; d.Consumables are not covered by warranty such as the tires, bearings, etc. e.Damages caused by unauthorized refit of the scooter; f.Damage caused by improper use and overloading and use in inappropriate conditions. g.Damages caused by natural disasters such as hurricanes, floods and earthquakes.

Dongguan Prestige Sporting Goods Company Limited

3rd Ind. District, Qiaotou Area, Houjie Town, Dongguan City, Guangdong Province, China Tel:0769-859 22501 Fax:0769-859 22505 E-mail: [email protected] Web:www.solaxtech.com

Other Scooter Manuals