SMARSECUR WS-S8A Manual 

Screws and anchors Documentation Presentation What is the WS-S8A? The WS-S8A is a Wireless Solar Siren compatible with SMARSECUR Secual alarm systems. Some advice before using your siren This siren features 2 tamper switches. If both one of them. Be careful when you open the siren (for setup) or when you remove it from a wall: the siren may ring out. We recommend you to connect your siren to your control panel before mounting it on a wall.

Design 1 Tamper switch LEDs Solar panel Loudspeaker 2 Tamper switch 5 Connection button 3 Siren duration 4 Power switch Internal view Side view

1 Switch on the siren Open the case of the siren with a screwdriver and place the siren’s power switch 4 on “ON”. The power switch is located under the silicone cover, inside the siren. 2 Adjust the siren duration Place the switch 3 inside the siren according to the duration you want (30 seconds, 1 minute, 3 minutes). Important, before going to step 3 - Make sure no delay is set up on your control panel - Do not trigger any detector during the connection of the siren, and do not stay in the scope of a motion detector - Do not use your remote control during the connection of the siren - Only mount your siren on a wall after you have connected it to your control panel.

To protect water from leaking into the circuit board, put back the silicone cover. Make sure the circuit board compartment is properly sealed. 3 Connect your siren to your control panel Press the Connection button 5 for one second. The LEDs light up: the siren is now in connection mode for 20 seconds. Press “Arm” or “SOS” on your control panel (not on the remote control). You hear one beep: the siren is now connected to the control panel. A piece of advice When holding the siren, make sure you do not press the tamper switch 1 : the siren may ring out.

The LEDs of the WS-S8A turn on for 4 seconds: the siren is armed. When you disarm the system The LEDs of the ES-S8A blink 6 times: the siren is disarmed. A piece of advice If you experience false alarms after having connected your siren to the control panel, we advise you to reset your siren and reconnect it to your control panel. When reconnecting your siren, make sure you do not trigger any detector and you do not use any remote control.

Change siren duration Open the case of the siren with a screwdriver and place the siren duration switch 3 according to the duration you want (30 seconds, 1 minute, 3 minutes). Remark If the duration of the control panel’s siren is superior to the duration of the siren, the siren will stop ringing out with the control panel’s siren. Reset 1. Press the connection button 5 for one second. 2. The LEDs light up: press the “Arm” button on the remote control. 3. Press the “Disarm” button of the remote control. 4. Press and hold the Connection button 5 of the siren until you hear 3 beeps (7 seconds): all accessories or control panels connected have been deleted from the siren.

standalone alarm system The WS-S8A can be used as a standalone alarm system: connect at least one remote control and at least one detector to the siren, and the siren will ring out everytime the detector is triggered (if the siren is armed). The siren supports up to 20 wireless accessories. Connect accessories to the siren Press the Connection button 5 for one second. The LEDs light up: the siren is now in connection mode for 20 seconds. Trigger the accessory (e.g. press the “Disarm” button on the remote control if you want to connect this remote control). You hear one beep: the accessory is now connected to the siren. If you hear 2 beeps, the accessory was already connected. Everyday use Arm the system. Press the “Arm” button of the remote control. The LEDs of the WS-S8A turn on for 4 seconds: the siren is armed. Disarm the system. Press the “Disarm” button of the remote control. The LEDs of the WS-S8A blink 6 times: the siren is disarmed.

Transmission distance 100 m (in open area) Power supply 1 solar panel 154.5 x 69.5 x 3.2 mm 5V / 60 mA Battery 18650 3.7V 2200 mAh Battery charging time Around 44h (depending on insolation) Current (standby) <3 mA Alarm current <200 mA Volume 100 dB (at 1m, with fully charged battery) Housing material ABS plastic Operating conditions Temperature: -10°C ~ +55°C Relative Humidity: ≤80% (non-condensing) Dimensions 162 x 182 x 65 mm Weight 650 g