Sinotrack ST-908 Operation & User’s Manual

1. Put the SIM Card in the tracker. 2. Connect the GPS and GSM antenna. 3. Connect the 4 pin and 6 pin wires. 4. Connect the Red and Black of 6 pin wires to 12V power. 5. Put the GPS antenna outside to get signal. Then the tracker will start, Wait for 2 minutes. If you have told us the APN you will use before shipment, Then you can add it to your account on software to track directly. If you haven’t told us your APN, you need to send SMS to change it: Send SMS: A000000,011,APN,APN User,APN Pass OR: A000000,011,APN (If it without user and pass of APN). The Tracker will connect to our software. You can login your account on our software to manage your trackers www.sinotrack.com or http:103.243.182.54

1. Working Directions..................................................................................................................…..4 2. GPS Tracker Installation...............................................................................................................4 2.1. Product Parts List ................................................................................................................4 2.2. Precaution before Installation ..............................................................................................5 2.3. Installation............................................................................................................................6 2.4. Wiring Description................................................................................................................7 3. Operating Instructions ..................................................................................................................8 4. SMS Tracking by Mobile..............................................................................................................11 4.1. Position Report Function.....................................................................................................11 4.2. Tracking Function................................................................................................................12 4.3. Stop tracking function888888..88888888888..8.88.............................12 5. GPRS Tracking by computer.......................................................................................................13 5.1. Set APN...............................................................................................................................13 5.1. Set IP and Port....................................................................................................................13 6. Take Photo function.....................................................................................................................14 6.1. Take photos.........................................................................................................................14 6.2. Take photos by press SOS button. .....................................................................................14 6.3. Set the time interval to take photos. ...................................................................................14 7. LCD Screen888.......................................................................................................................15 7.1. Use as navigation................................................................................................................15 7.2. Make and receive phone calls. ...........................................................................................15 7.3. Receive massages from control center. .............................................................................15 7.4. Receive GPS signal. ...........................................................................................................15 8. Fuel Sensor8888 8 8 8 888888888888888888888888888815 9. Temperature sensor8888888888888888888888888.888888 815

Thank you for your purchase of ST-908 Vehicle GPS Tracker. In order to realize the full functions of this product, please read this manual carefully before starting to use the product. 1. This product can only be maintained and repaired by qualified professional service personnel. If you detach this product for maintenance or repair, your warranty will be invalidated. 2. When connecting the other devices, read carefully their instruction manuals, so as to carry out correct installation; do not connect incompatible device. 3. Please use genuine original parts and qualified batteries and peripheral equipments, so as to avoid damage to this product. 4. As this product is a high-tech product, please read carefully this manual before starting to use the product, so as to avoid inappropriate operation. 5. Drivers should not operate this product while driving a vehicle, thereby, affecting safe driving. 6. This product can work properly only when GSM communication is in good condition. 7. Please reduce electromagnetic wave interference to the product; and use it properly. 8. GPS communication is liable to be affected by environmental shielding; may fail to carry out positioning during certain circumstances. It will resume the positioning function as soon as it leaves the shielding environment. This is normal. Please do not worry when encountering such problem. 9. Each signal sent out from the system will be confirmed for successful transmission in the base station of the mobile operator. However, if system stoppage occurs or if the mobile telephone is preset to a switch off state by the customer, it cannot ensure successful transmission. 10. For safety reason, do not tell the other people your ST-908 mobile number, without taking precautions. Otherwise, your privacy may be compromised along with other safety problem.

2.1. Product Parts List GPS Tracker Unit GPS Antenna GSM Antenna Car Charger Lighter Socket

1 Check if all the parts are included. 2 Prepare a SIM card for GSM communication. Use some other mobile phone to confirm that the PIN code has not been set and that it can dial out and receive telephone calls and SMS without problem. 3 Before install the SIM card; make sure to cut off power from the GPS Tracker unit. The correct installation method is to push the tray completely into the GPS Tracker unit, until you feel it is hooked by something. 4 Find a suitable place inside the car for installing the unit. 5 Check if all the wiring has been connected correctly; then connect the GPS Tracker unit to the power source. 2.3. INSTALLATION 2.3.1 Step 1: Install SIM Card 1 Using a speculate object to poke the small button of the SIM card seat, and then it will pop-up a small drawer. 2 Put the SIM card in the drawer, and put back the drawer, as direction shown in the picture. 3 Make sure to turn off the power before install the SIM card. 4 Make sure to deactivate the PIN code, so that the SIM card can operate without PIN protection. 5 Before install the SIM card to the GPS Tracker, please use a mobile phone to make sure the SIM card can make & receive phone calls without problem. 6 Before install the SIM card to the GPS Tracker, please use a mobile phone to empty the SMS storage of the SIM card. 2.3.2 Step 2: Connect GSM Antenna 1 Connect the GSM Antenna to the unit. 2 Fasten the connection by turning the screw in the bottom. 3 Please do not swing round the antenna itself.

1 GPS antenna is used to receive satellite signals in the sky. It should be positioned at a place where it will have an unobstructed view of the sky. The ideal location is top of the dashboard or close to the rear window of the car. 2 GPS antenna can pick up signals through glass and plastic, but will not "see the sky" through metal or other conductive surfaces. To avoid distractions of GPS signal, make sure the antenna is not covered or shielded by any object containing metal, such as the metallic windshield. 3 If your car is with metallic windshield please cut a hole on the windshield above the place where you put the GPS antenna, so that the antenna can receive the GPS signals. 2.3.4 Step 4: Connect power charging ST-908 connects to the 4pin and 6pin wires. 2.4. Wiring Description 4 pins connector Pin Color function 1 Red power switch 2 Red power switch 3 Yellow Connect to door sensor 4 Green Undefined input. for example you can use it to detect the signal of car alarm

Pin Color function 1 Red DC in Input voltage: 8-40V Suggestion: 12V 2 Black GND 3 Brown Output , starter kill relay you can use it to cut the electricity or oil of the car 4 White SOS button 5 Green Output , starter kill relay you can use it to cut the electricity or oil of the car 6 Blue ACC signal detecting According to the relay parameter to make sure to following requirement: The input voltage of relay must be suited to the car battery 3. Operating Instructions SMS protocol of AL-900C/E, the default password of AL-900C/E is 000000 SMS Instruction Format Remark 1 Request one position A******,000 000: command code ******: password, default 000000 2 Modify user password A******,001,###### 001: command code ******: old password , default 000000 ######: new password 3 Set a preset phone number for SOS button or monitoring number. A******,002,1, Tel Number 002: command code ******: password, default 000000 1 : Set SOS number Tel Number: Preset Tel. number (Tel Number must <20 digits ) When this button is pressed, AL-900C/E will send the SOS and position message to the preset A******,002,2, Tel Number 002: command code ******: password, default 000000 2 : Set monitoring number Tel Number: Preset Tel. number

4 Set the time interval of position refresh to SOS number A******,003,XXX 003: command code ******: password, default 000000 XXX: (3 digital) XXX =000,stop XXX = 001 – 999 time internal (unit: min) 5 Set low power alarm When the AL-900C/E voltage is lower than the pre-set value, AL-900C/E will send one lower power alarm SMS to the control number. Otherwise, there is not this function in vehicle tracker A******,004,X 004: command code ******: password, default 000000 X : voltage preset value X=0, close (default ) X =1, <3.5V send SMS alarm X =2, <3.6V send SMS alarm X =3, <3.7V send SMS alarm X =4, <3.8V send SMS alarm X =5, <3.9V send SMS alarm 6 Set over speed alarm When the AL-900C/E speed higher than the preset value, AL-900C/E will send one over speed alarm SMS to the control number. A******,005,XX 005: command code ******: password, default 000000 XX : the speed preset value XX = 00 , close 01 ≤ XX ≤ 99 (unit: XX Km/h) 7 GPRS Status, To check GPRS Status A******,502 502: command code ******: password, default 000000 8 Get IMEI A******,505 505: command code ******: password, default 000000 9 Set GPRS internal of position refresh A******,506,00030 506: command code ******: password, default 000000 00030: Such as 30 seconds interval is 00030 10 Check GPRS interval of position refresh A******,507 507: command code ******: password, default 000000 11 Inquire GPRS parameter Return Including IP, Port, APN A******,006 006: command code ******: password, default 000000

A******,007,P,F 007: command code ******: password, default 000000 P: the position of the output P =1 output 1 P =2 output 2 F: the control signal F =1 give the relay the current to drive it (cut off the car power). F =0 cut off the current of the relay (comeback the normal). 13 Time zone setting A******,008,+08 008: command code ******: password, default 000000 +8: Set the local time zone, the default value is +8 14 Inquire the system parameter. Including the software version, password, interval, speed limit, area limit, I/O state, GPS state, SOS number, control number, etc A******,009 009: command code ******: password, default 000000 15 GPRS switch A******,010,X 010: command code ******: password, default 000000 X: GPRS function =0 GPRS OFF =1 GPRS UDP =2 GPRS TCP 16 SET APN A******,011,APN, username,password 011: command code ******: password, default 000000 APN: GPRS use this gateway to connect internet. Username: APN Username Password: APN Password The default APN is CMNET 17 Set the center IP and A******,012,IP:Port 012: command code

******: password, default 000000 IP: Platform server ip Port: Platform server port 18 LED Light Switch A******,666, X 666: command code ******: password, default 000000 X: LED Light Switch X =0 LED Light OFF X =1 LED Light ON 19 Reset to factory settings A******,888 888: command code ******: password, default 000000 20 Restart Tracker A******,999 999: command code ******: password, default 000000 4. SMS Tracking by Mobile 4.1. Position Report Function 4.1.1. Get position from vehicle - way 1: No matter where you are, when you want to know the position of your vehicle Step1 Send a SMS message or make a telephone call to the AL-900C/E. Step2 vehicle will report its location back to you by SMS, which including the position information Edit a message as following format, and then send it to ST-908: Command Remark Send Format: A+Password+,+000 Get position command code is: 000 For Example Send message: A000000,000 000: command code 000000: password, default 000000 Back information: Lat:2232.6022N, Lon:11402.2969E This mean your position is on North Latitude 22 degree 32.2232 cent and East Longitude 114 degree 2.2969 cent

Apply for one position service by another way: you need pre-storage the phone number in SIM card: Step1 Make a cell phone call to AL-900C/E Step2 After listen the ring of AL-900C/E, it will hold off after two rings. Step3 Then, after 10 second, the cell phone will receive the Position SMS. (Its means is AL-900C/E will send Position Data every 5 minute.) 4.2. Tracking Function Tracking report function can be turned on or off according to the requirements of the user. Tracking function will continually report vehicle position until it get stop command .In this tracking mode, ST-908 will send one position message at a preset time interval. Step1. Edit a message as following format, then send it to ST-908 Command Remark Send Format: A+Password+,+003,+XXX Note: XXX , if XXX=000 it is STOP tracking Unit: preset minute interval Command code : 003 For example: A000000,003,003 003: command code 000000: password, default 000000 003: 3 minute interval It means is AL-900C/E will send Position Data every 3 minute. Step2. AL-900C/E will send back one SMS-----Set Time OK. This SMS means that ST-908 is in tracking mode now and preset time interval is 3 minutes. Step3. AL-900C/E will send back position SMS at preset time interval. In this example, the SMS will send back at preset time interval: 3 minute

This function is used to turn off tracking report function. Edit a message as following format, and then send it to AL-900C/E: Command Remark Command format: A+passwaord+,+003+,+000 For example: A000000,003,000 003: command code 000000: password, default 000: 0 minute interval, mean stop back 5. GPRS Tracking by Computer The default mode is GPRS when powering on the unit. The default setting is ours; you need to send the following SMS to Set APN and IP, Port. (If you use our server, you only need to set APN). 5.1. Set APN Send the SMS to the tracker as following format Command Remark Command format: A+Password+,+011,+APN For example: A000000,011,CMNET 011 : Command code 000000: password, default 000000 CMNET: APN, is gateway to connect internet, Each country is different, 5.2.Set IP and Port Send the SMS to the tracker as following format: Command Remark Command format: A+Password+,+012,+IP:Port For example: A000000, 012,121.201.110.62:7000 012 : Command code 000000: password, default 000000 121.201.110.62 Platform server IP 7000: Platform server software Port When the AL-900C/E connect to the monitor system, the power LED flash by 1 S. Then you can login in the tracking server to manage your car.

Connect the Camera to ST-908, You can send a command to take photographs; the car terminal will shoot pictures and spread to Center. After that, pictures will display on the operation platform. 6.1. Take photos on software. 6.2. Take photos by press SOS button. 6.3. Send SMS command to set the time interval to take photos. Such as 30 minutes to take a photo and send back to software.

7.1. Use as navigation. 7.2. Make and receive phone calls. 7.3. Receive massages from control center. 7.4. Receive GPS signal. 8. Fuel Sensor (only for ST-908) 9. Temperature Sensor (only for ST-908) Open http://www.online-track.com or http://121.201.110.62/ to begin tracking.

Or add our Skype to talk with us online: ■ Email: [email protected] [email protected] ■ Skype: ventureshi autoleaders.sun About distributors: We have distributors in Asian, Middle East, North American, South American, Africa, and European, over 60 countries. If you need local technical support, or purchase our products from local distributor, please contact us. We’ll send their contact info to you, or let them contact you directly.