Voxx Electronics Prestige APS997Z Quick Installation Manual

2 Pink Ignition 3 Flex Relay (30) Output 3 Yellow Starter Output (+) 4 Green Ignition 2 Output (+) 5 Red Battery 12V Input (+) 6 Red/White Battery 12V Input (+) 7 Purple Accessory Output (+) 8 Blue Ignition 1 Input / Output (+) 8 Pin Start P P P 1 White Parking Light (30) Output 2 White/Red Parking Light (87) Input 3 White/Black Siren Output (+) 4 Black Ground Input (-) 4 Pin Light P 1 White Data RX 2 Black Ground (-) 3 Blue Data TX 4 Red Battery 12V (+) DBI 1 Green Data RX 2 Blue Data TX 3 Black Ground (-) 4 Red Battery 12V (+) RF 1 Blue Data TX 2 White Data RX 3 Black Ground (-) 4 Red Battery 12V (+) CarLink 4 Red Battery 12V (+) 3 Black Ground (-) 2 White Data RX 1 Blue Data TX Weblink 22 Green Unlock Output (-) (NOC 11) 21 Dk. Blue Trunk Output (-) (NOC 9) 20 Red Lock Output (-) (NOC 10) 19 Green/Lt. Blue Ch. 4 AUX Output (-) (NOC 8) 18 Black/White Horn Output (-) 17 Lt. Blue/Green Ch. 5 AUX Output (-) (NOC 7) 16 Red/Black 2nd Unlock Output (-) (NOC 12) 15 Black/Lt. Green Factory Arm Output (-) NOC 6) 14 Brown/Black Brake Input (+) 13 Black/Blue Factory Disarm Output (-) (NOC 5) 12 Dk. Blue/Black External Activation Input (-) 11 Black/Red Pulse After Shutdown Output (-) (NOC 4) 10 Orange/Black Parking Brake Input (-) 9 Black/Yellow Pulse During Crank Output (-) (NOC 3) 8 Green/Yellow Diesel Glow Plug Input (+) 7 Green/White DomeLight Output (-) (NOC 2) 6 Purple/Brown Door Trigger Input (- / +) 5 Lt. Blue Remote Start Status Output (-) (NOC 1) 4 Green/Orange Tach Input (-) 3 Gray/Black Hood Input (-) 2 Lt. Green Trunk Trigger Input (-) 1 Orange Starter Kill Relay / Anti-Grind Output (-) 22 Pin Input/Output 4 Red Battery 12V (+) 3 Black Data TX 2 Green Warn Away Input (-) 1 Blue Full Trigger Input (-) Shock 1 2 3 4 VOXX FLCART Dock Replacement Part #4120459 Replacement Part #4120457 Replacement Part #4120462 Replacement Part #4120458 Not Included Not Included Not Included 85 Red Ignition Input (+) 86 Orange Starter Kill Input (-) 87A Black Starter Interrupt - Key Side 30 White/Black Starter Interrupt - Motor Side Starter Kill 86 85 87 87A 30 Replacement Part #4360828 Replacement Part #4360830 This Harness is included with the FLCART. For Wire Information and Diagram Please Refer to Vehicle Specific FlashLogic Install Guide. Visit www.FlashLogic.com for More Information. Not Included 19 17 15 13 11 9 7 5 3 1 2 4 6 8 10 12 14 16 18 20 21 22 19 20 17 18 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 1 3 5 7 2 4 6 8 1 3 2 4 1 2 3 4 Replacement Part #4120464 APS997Z Security and Remote Start System Layout 2018 Voxx Electronics. All Rights Reserved. Shock Sensor Part #4700033 4180075 18LCDSP 185SP

Quick Installation Guide For Complete Installation Guide and Technical Support Please Visit www.voxxuniversity.com Or Call 1-800-225-6074 Notifications Feature Programming Remote Programming 1 Chirp 2 Chirp 3 Chirp 4 Chirp 5 Chirp 6 Chirp 1 Lock / Unlock Function 500ms 3.5sec 500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL 2 Ignition Lock OFF ON 3 Ignition Unlock OFF Unlock All Unlock Driver 4 Exterior Illumination OFF With Arm With Disarm With Arm & Disarm 5 Auto Relock OFF Auto Lock Only Auto Lock & Arm 6 Auto Arming / Locking OFF Auto Arm Only Auto Lock & Arm 7 Notification Sound Both Siren Horn 8 Horn Timing 16ms 30ms 40ms 50ms 10ms 9 Valet Override Method Valet Custom Code Stand Alone Valet 10 Driver Priority Unlock OFF ON 11 Silent Choice OFF From Transmitter OEM Style 12 Security Profile All On Doors off Hood / trunk Off All Off 13 Door Trigger Input Negative Positive 14 Park Light / Trunk Swap OFF ON 15 Data Port Protocol ADS DBI 1 Chirp 2 Chirp 3 Chirp 4 chirp 5 Chirp 6 Chirp 1 Defrost Output Pulsed 10min RS Runtime 2 RS Start Notification ON OFF 3 RS Runtime 5min 10min 15min 20min 45min 60min 4 RS Parking Lights Steady Flashing 5 Engine Confirmation Tach Voltage Data Hybrid 6 Voltage Level >0.5v B4 Start <0.5v B4 Start 7 Ignition 2 Output Ignition Accessory Start 8 Ignition 3 Output Ignition Accessory Start 9 Accessory Output Accessory Ignition Start 10 Transmission Auto Manual 11 Max Crank Time 0.8sec 1.0sec 1.5sec 2.0sec 3.0sec 4.0sec 12 Diesel Delay OFF Diesel 10 Diesel 15 Diesel 20 Diesel 30 13 Temperature Start OFF ON 14 Crank Duration Averaging Preset 15 RS Shock Override Shunt until Clear Shunt RS Cycle Shunt From TX 16 Turbo Timer OFF 3min 5min 10min 17 Start Activation Two Press One Press Three Press 18 RS Lock Function No Change UL Before L After UL Before Start Lock After Start 19 Factory Disarm Output Single Pulse Double Pulse 350ms 500ms 800ms Same As Bank 2, F1 20 Additional Unlock Pulse No Pulse IGN, ACC, GWR IGN,ACC,GWR,PASD Features Feature Bank 2 Options Features Feature Bank 3 Options 1 Second Pulse 10 Second Pulse 15 Second Pulse 20 Second Pulse 30 Second Pulse Push & Hold Latch ON/OFF Latch 10min Latch Runtime 5 Second Pulse Ch. 4 AUX Lock Unlock 2nd Unlock Trunk Remote Start Status Ignition Pulse After Shutdown Domelight Headlight Defrost LED Ch. 5 AUX Ch. 6 AUX Ch. 7 AUX Pulse During Crank Accessory Factory Arm Factory Disarm 2018 Voxx Electronics. All Rights Reserved. Tach Programming Dome Delay Programming 1 Runtime Expired 2 Remote Shutdown 3 Brake On 4 Manual Mode 5 Hood Open 6 Low / No Tach 7 Tach Programming 8 High Tach 1 Shock 2 Trunk / Hood 3 Door Negative Output Control (NOC) AUX Output Control Shock Sensor The APS997Z includes two (2) programmed remotes. If required, additional remotes can be programmed to the system. Remote Programming is located in Feature Bank 1. To enter Remote Auto Programming: 1. Turn the ignition key to ON. 2. Press and release the valet button 3x. System will beep and flash the parking lights 1x. Press the lock button on each remote. The system will beep 1x to indicate the remote has been programmed. If programming one (1) button remotes, press the Start button. Only primary remote functions are auto programmed. This Includes Lock, Unlock, and Trunk/ Start. If using AUX output control, the remote channel must be manually programmed to the system AUX output. Please see the complete installation guide for manual remote programming instruction. Note: If programming 2-Way remotes, wait for remote to beep before programming another remote. This beep is confirmation that a 2-Way response has been received from the main module. Any AUX output can be configured using the AUX Control Menu. This feature is only accessible via FlashLogic Weblink or Weblink Mobile. Negative output control allows any NOC to be programmed for any one of nineteen (19) options. This feature is accessible via FlashLogic Weblink or Weblink Mobile. Alarm When the alarm is triggered the system will provide feedback to the user. Upon disarm, the system will beep 4x and flash the LED to indicate the Alarm Trigger Zone. Chirp Delete System ARM/DISARM chirps can be toggled ON or OFF without entering the Feature Bank programming. 1. Turn the ignition key ON/OFF. 2. Press and release the valet button 3x. The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This feature will not affect alarm trigger or programming. User Programmable LED System LED notifications can be turned ON or OFF without entering Feature Bank programming. 1. Turn the ignition key ON/OFF, ON/OFF. 2. Press and hold valet button for five (5) seconds. The LED will flash 1x for ON, 2x for OFF. This feature will not affect LED flash during programming. Remote Start If the remote start fails to start the vehicle, the system will flash the vehicle parking lights to indicate the cause. The installer must manually configure the Engine Confirmation method in Feature Bank 3, Feature 5. The default method is “Tach”. This method requires using the Green/Orange tach input wire. When using the default “Tach” method, the vehicle tach rate must be programmed. To enter tach rate programming: 1. Turn the ignition key ON. 2. Press and release the valet button 3x. 3. Turn the ignition key OFF. 4. Press and hold valet button. 5. While holding valet button, start the engine using the key. 6. Hold the valet button for approximately ten (10) seconds. If connected to the vehicle Tach source, the system will flash the parking lights 1x every second. 7. Release the valet button. The system will turn on the parking lights for two (2) seconds to indicate the tach rate is programmed. The APS997Z Feature Banks can be programmed by using the valet button and remote. To enter Feature Bank programming: 1. Turn the ignition key to ON. 2. Press and release the valet button 3x. System will beep and flash lights 1x for Feature Bank 1, Remote Programming. 3. Cycle ignition key OFF/ON. System will beep and flash lights 2x for Feature Bank 2. 4. Press valet button to cycle features. LED will flash to display feature number. 5. Press lock button to cycle options. System will beep to indicate option number. 6. Cycle ignition key OFF/ON. System will beep and flash lights 3x for Feature Bank 3. 7. Press valet button to cycle features. LED will flash to display feature number. 8. Press lock to cycle options. System will beep to indicate option Number. To exit Programming cycle ignition key OFF and wait ten (10) seconds. The System will also automatically exit programming after sixty (60) seconds of no activity. Important Update The default Data Port Protocol of this system is ADS. If using an FLCAN or other external integration module be sure to choose iDatalink 2-Way when flashing. This system will also support DBI. This will require programming Feature Bank 2, Feature 15 to DBI. The shock sensor should be mounted to a solid surface in the center of the vehicle. Once mounted the shock sensor will require adjustment. To increase sensitivity: Turn adjustment dial clockwise. To decrease sensitivity: Turn adjustment dial counter clockwise. To test sensitivity, strike the vehicle with an open palm. Adjust the dial to provide coverage to as much of the vehicle as possible. This system can be programmed to ignore the vehicle’s theater dimming dome light. This feature will be used when connecting the door trigger input to the dome light circuit for alarm trigger. Note: Vehicle windows should be open to prevent accidental locking of keys in the vehicle. Start with all doors closed and the vehicle dome light off. 1. Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light solid. 2. Open and close the driver door. The system will monitor the dome light circuit. When the dome light turns off the system will set the delay time and add an additional two (2) seconds. Dome Delay Reset 1. Key ON/OFF, ON/OFF, ON/OFF. 2. Press and hold valet button for five (5) seconds. The system will beep 1x to indicate reset is complete. The Feature Banks below can also be programmed using the FlashLogic Weblink or Weblink Mobile. Please visit www.FlashLogic.com for more detail.