Tree Frogs 5.4 Texan Install Manual

Tape Measure 24” Level Angle Square Phillips Screw Driver 3/8” Cordless Drill or Electric Drill 3/8” Drive Ratchet or Electric Impact Gun Claw Hammeror Rubber Mallet Pliers or Vise Grips 7/16” Deep Well Socket 9/16” Deep Well Socket 3/4” Deep Well Socket 1/8”, 1/4”, and 9/16” Drill Bits Phillips Head Screw Bits An Adult with two Adult Helpers Please familiarize yourself with the install manual, parts/components and general construction process of your new swing set before getting started. Approximate assembly time: 6 to 8 hours. 6 foot unobstructed safety perimeter around swing set recommended. 5.4 Texan Playcenter Install Manual Version 3.14 Houston, TX 77041 • www.treefrogsswingsets.com • © 2013 kID STRUCTURES INC.

are some recommendations to help you locate and install a safe play area. ● This play set is designed for the use of 4 occupants who have a combined weight not exceeding 800 pounds on the elevated floor; 3 occupants who have a combined weight of 525 pounds on the swing area; for a total Unit capacity of 5 occupants who have a combined weight of 1325. (this weight is not including the picnic table area) ● On-site adult supervision is required. ● The swing set should be located on level ground. The stationary components such as ladders and slides are required to be a minimum of six feet from any structure or obstruction such as a fence, garage, house, tree, overhanging branches, electrical wires, clotheslines, etc. Any swinging equipment is also required to be a minimum distance twice the height of the swing beam away from these obstructions or structures as well. The swing set should be located a safe distance from any water hazards, such as a lake, river, bayou, swimming pool, etc. ● Do not install this residential swing set in a commercial setting. This swing set is not manufactured for commercial usage and will void all warranties. Tree Frogs Wooden Swing Set Factory is not responsible for any damages or injuries resulting from this swing set being used in a commercial setting. ● Never install this swing set indoors; or over concrete, asphalt, packed earth, grass, carpet or any other hard surface. A fall onto a hard surface can result in serious or fatal injury. ● The U.S. Consumer Product Safety Commission (CPSC) recommends that you install and maintain a resilient surface under your swing set. The CPSC’s Consumer Information Sheet for Playground Surfacing Materials is on the next page. A resilient surface, should be installed after the swing set has been completely assembled according to these instructions. The swing set must rest on solid ground. Please note that this swing set has a maximum fall height of 7’. Here are some maintenance tips required to insure safe play on your swing set for years of fun. ● At the beginning of each usage season and every two weeks during, check: nuts and bolts and tighten as needed, swing seats, chains, ladders, slides, rope and wood components for sign of deterioration and replace if necessary. ● On a yearly basis, we recommend that you coat your swing set with a sealant or preservative. You may also want to spot sand any areas prior to sealing. ** Special note: Although we recommend that you reseal your swing set annually, you may have to touch up the high traffic areas and/or areas that have a high exposure to direct sunlight.** ● Be sure that the sealant you select is non-toxic and child safe. Your local Tree Frogs Wooden Swing Set Factory dealer may offer a complete power wash and reseal and maintenance program. ● Do not use line trimmers or “weed eaters” around your swing set. The line will remove both paint and wood from uprights and base pieces. Any damage resulting from this type of abuse is not covered under our limited warranty. ● Remove plastic swing seats and take in doors or do not use when temperature drops below 0°F. Please keep this install manual for future reference. Weight Limits for Tree Frogs Swing Sets Fort Platform: 800 Lbs. Total Weight Swing Belts: 175 Lbs. Trapeze: 125 Lbs. Full Bucket Swing: 50 Lbs. Toddler Bucket Swing: 50 Lbs. Tire Swing: 125 Lbs. Total Weight Rope Ladder: 75 Lbs. Rock Wall: 150 Lbs. All Slides: 125 Lbs. Tree Frogs recommends that the weight limits for all components must not be exceeded. Failure to adhere to these and other safety guidelines could result in damage to the swing set and/or injury to the users.

● Not to walk close to, in front of, behind, or between moving items. ● Not to swing empty swing seats. ● Not to swing sideways into the path of adjacent swings. ● Not to use the swing set in a manner other than that for which it is intended. ● Not to get off the equipment while it is in motion. ● Not to jump off the tower. ● Not to stand in the swing seats. ● Not to swing so high that chains become slack, or above the height of the swing support. ● Not to jump on a slide. ● Not to climb on top of the swing support. ● Not to attach to the swing set any item that is not specifically designed for use with the equipment, such as (but not limited to) jump ropes, clotheslines, pet leashes, cables, and chains. These may become strangulation hazards. ● To hold on to swings and climbers with both hands. ● To slide feet first, never head first. ● To watch for other children while swinging or playing near the swing set. To also insure SAFE PLAY adults must: ● Limit climbing and swinging heights to each child’s ability. ● Verify that suspended climbing ropes are secured at both ends. ● Verify that suspended climbing ropes cannot be looped back on themselves. ● Dress children appropriately for play. Use well-fitted shoes that do not have slippery soles. ● Avoid ponchos, scarves, hoods, loose fitting clothing, neckties, and any clothing with a drawstring. Serious injury could result should any part of the children’s clothing become entangled in the swing set. ● Do not allow children to play wearing helmets. ● Remember that children are inventive. When they develop games that are unsafe, be alert and change the rules. IMPORTANT - PLEASE READ As fresh lumber acclimates to its new environment, the natural tendencies of the tree can show itself in the form of checks, or “cracks” in the lumber. In almost all cases this is normal and it will not affect the structural integrity of your play set. Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, checking or any other physical properties of wood that do not present a safety hazard, are not covered by this warranty. Defects that develop because the product is exposed to extreme climate conditions are not covered by this warranty. Defects that develop as a result of faulty or improper installation of the product are also not covered by this warranty. Most cracks are not warrantable, however if you believe that the integrity of your play set is compromised by this natural occurrence, please contact the Tree Frogs Swing Set Dealer that you purchased your swing set from. We appreciate your purchase and know that you will enjoy your play system for many years to come.

inventory of parts; therefore, we recommend you set aside a full two days for assembly. ● Identify all of the parts for your play set. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. ● After everything is laid out, check carefully to ensure all parts are present. Make sure there are no broken boards. ● Find an area to sort your hardware. It is best to open the hardware on a solid surface so that you do not lose any pieces in the grass. This will save time and familiarize you with all the different pieces in the hardware bag. **Important note: Wood has some natural defects such as knots, surface cracks, etc... We reject parts that are structurally defective. We use a high quality lumber in our structures; however, you should inspect each part for splinters or rough spots and sand them smooth to prevent injury.** ● After familiarizing yourself with all of the components, read all instructions thoroughly. Reading instructions after you have studied the parts will help you understand more clearly the installation process, and help to eliminate unnecessary mistakes. ● Pay close attention to the diameter and length of each bolt and screw. ● Never tighten hardware completely at first. It helps to have some adjustment for bolt alignment while you are attaching parts together. After everything is square, tighten each joint. ● After the main unit is assembled it is critical that the floor is level and square. If the main frame is not level, the walls and floor will be out of square. ● After you complete installation, make sure every bolt, screw, and nut is tight, and every board is secure. Wood will expand and contract with the seasons. ● Place the set on level ground, not less than 6ft from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. ● All 1/4” and 3/8” lag bolts must have pre-drilled holes 1-1/2” to 2” deep. Use a 1/8” drill bit for the 1/4” lag bolts and 1/4” drill bit for 3/8” lag bolts. Use pre-drilled holes in facias as a reference for placing lag bolt pilot holes. ● If a board lifts or rises causing a gap between boards when running in lag bolts or screws, back out the screw or lag bolt and press or apply pressure (but not enough to crack or break board) while re¬running in the lag bolt or screw in the same hole. ● Do not over tighten bolts, lag bolts or screws. You can damage boards, break hardware, and/or strip out the hardware. ● When using hammer do not beat on the hardware, but gently tap it in. Never beat on the wood as it will leave marks. ● Complete the steps which will be the basic frame of the fort {i.e. four corner posts with base (sand box boards) and deck supports} ● Position in the most level area chosen for the play set, keeping in mind the location and size of the swing beam, ladder, slides, etc. that extend off the fort. ● Once the frame is in the final position, check for vertical and horizontal levelness to determine which side(s) will need to be dug into the ground to level the play set. ● With a shovel, score the ground around the outside edges of the sandbox boards on the ‘high’ side of the fort. This is the area that will be dug in. Make sure to score deep enough; the scored lines will be your digging template. ● Push the frame off and away from the scored area, far enough to dig and remove dirt to reach the appropriate depth. ● Dig a channel along the scored line(s) for the base of the fort (corner post and sandbox boards) to rest into. Dig the channel(s) to the same level depth. The bottom of the channel(s) should be level to each other so your frame doesn’t teeter or rock because the channel(s) are uneven. ● Once you have removed enough grass and dirt, slide/push the frame into the channel(s). Place a level on the vertical and horizontal boards of the frame to determine if enough soil, or too much, was removed. ● Repeat this process until the basic frame is plumb and level and in its final position before completing the rest of the assembly. ● Measure to make sure fort is square. ** Important: if you require a channel depth of more than 6”, then we recommend you have your play set area professionally graded before completing assembly. **

The U.S. Consumer Product Safety Commission (CPSC) estimates that about 100,000 playground equipment related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall onto a shock- absorbing surface is less likely to cause a serious injury than a fall onto a hard surface. However, it should be recognized that some injuries from falls will occur no matter what playground surfacing material is used. Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Grass may appear to be acceptable, but can turn to hard packed earth in areas of high traffic. Shredded bark mulch, wood chips, or fine gravel are considered to be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around play equipment. TABLE 1 -CRITICAL HEIGHTS (in feet) OF TESTED MATERIAL MATERIAL UNCOMPRESSED DEPTH COMPRESSED DEPTH 6 Inch 9 Inch 12 Inch 9 inch Wood Chips 7 10 11 10 Double Shredded Bark Mulch 6 10 11 7 Engineered Wood Fibers 6 7 >12 6 Fine Sand 5 5 9 5 Coarse Sand 5 5 6 4 Fine Gravel 6 7 10 6 Medium Gravel 5 5 6 5 Shredded Tires** 10-12 N/A N/A N/A ** This is data from tests conducted by independent testing laboratories on a 6 inch depth of uncompressed shredded tire samples produced by four manufacturers. The test reported critical heights, which varied from 10 feet to greater than 12 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F1292. Table 1 should be read as follows: If, for example, uncompressed wood chips are used at a minimum of 6 inches, the Critical Height is 7 feet. If 9 inches of uncompressed wood chips are used, the Critical Height is 10 feet. It should be noted that, for some materials, the Critical Height decreases when the material is compressed. It is recommended that a shock absorbing material should extend a minimum of 6 feet in all directions from the perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure. This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of a material depends on the type and height of the playground equipment, the availability in your area, and its cost. This information has been extracted from the CPSC publications “Playground Surfacing-Technical Information Guide” and “Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending a postcard to: Office of Public Affairs U.S. Consumer Product Safety Commission Washington, D.C. 20207 Toll-free Hotline: 1-800-638-2772 or at http://www.cpsc.gov

Item No. UB-1 ub-2 ub-3 ub-4 ub-5 ub-6 ub-7 ub-8 ub-9 ub-10 ub-11 ub-12 Part Number 17-4-00186 16-4-00213 16-4-00216 16-4-00217 17-4-00106 17-4-00107 16-4-00215 12-4-00141 16-4-00218 16-4-00214 16-4-00223 16-4-00224 Part Description Universal Playcenter Mainbeam Uni. Playcenter Center Post (l) Gusset Bracket (R) Gusset bracket (l) Playcenter Support Gusset (R) Playcenter support gusset universal Rope block universal rail Bottom universal entrapment block uni. playcenter corner post uni. pc. top joist w/ swing holes uni. pc. top joist QTY. 2 2 5 5 2 2 1 3 1 4 1 1 Texan Playcenter Bundle tx-1 tx-2 tx-3 tx-4 tx-5 tx-6 16-4-00220 12-4-00146 12-4-00145 16-4-00221 16-4-00219 16-4-00222 Texan Playcenter upper rope arm texan playcenter tarp board Universal Tarp Board texan playcenteer ground runner texan playcenter lower rope runner texan playcenter upper accessory arm 1 2 1 1 1 1 5.4 Texan Playcenter Bundle A. 5tx-1 5tx-2 5tx-3 5tx-4 5tx-5 5tx-6 5tx-7 5tx-8 5tx-9 5tx-10 5tx-11 16-4-00320 16-4-00321 16-4-00322 13-4-00066 16-4-00323 16-4-00324 11-4-00103 11-4-00102 11-4-00101 10-4-00201 64-6-00003 (l) playcenter wood step ladder leg center wood step/ chain ladder leg (r) playcenter chain ladder leg 5 1/4” wood step (R) PC rockwall ladder leg (l) pc rockwall ladder leg tx pc rockwall board w/ out holes tx pc rockwall board w/ holes tx pc rockwall board w/ rope hole tx pc rockwall board blank rope run-cedar 1 1 1 6 1 1 4 8 1 1 6

Item No. wr-1 wr-2 wr-3 wr-4 wr-5 wr-6 wr-7 wr-8 wr-9 wr-10 wr-11 wr-12 wr-13 wr-14 wr-15 wr-16 Part Number 10-4-00348 12-4-00204 12-4-00205 19-4-00092 19-4-00093 12-4-00208 12-4-00209 10-4-00346 10-4-00347 20-4-00005 10-4-00209 10-4-00212 10-4-00210 10-4-00213 10-4-00214 10-4-00211 Part Description TX PC Wood roof tarp board Uni. pc (l) wood roof support uni. pc (r) wood roof support TX PC wood roof board tx pc wood roof board ripped qc pc wood roof runner qc pc wood roof runner #2 qc pc wood roof center support qc pc wood roof center support #2 universal center fan board universal pc bottom fan board universal pc center fan board uni. pc. Long (l) side fan board uni. pc. Long (r) side fan board uni. pc. short (r) side fan board uni. pc. short (l) side fan board QTY. 1 2 2 32 2 4 4 2 2 2 2 2 2 2 2 2 Universal Rail(Count is for a single rail) ra-1 ra-2 ra-3 Universal rail top universal rail bottom universal spindle 1 1 5 Universal Deck Deck-1 DECK-2 DECK-3 DECK-4 12-4-00138 13-4-00063 12-4-00139 13-4-00064 Deck Runner Deck Support Small Deck Board Large Deck Board 4 2 8 6 5.4 Texan PC Box a. or b.(color depends on box) 5pc-1 5pc-2 5pc-3 5pc-4 5pc-5 5pc-6 5pc-7 5pc-8 5pc-9 5pc-10 36-1-00023 36-1-00024 65-7-00017 65-7-00019 37-1-00019 37-1-00018 51-1-00031 51-1-00032 56-1-00015 60-1-00006 large rock (multi- color) large rock (green) 14’ yellow rope 17’ yellow rope 19” ships wheel (green) 19” ships wheel (yellow) 43” plastisol coated chain (yellow) 43” plastisol coated chain (green) tire swivel 20” trapeze bar w/ rings (yellow) 16 16 1 3 1 1 1 1 1 1

Item No. tb-1 tb-2 tb-3 Part Number 61-8-00055 61-8-00056 61-8-00054 Part Description tx pc tarp bag (byb) tx pc tarp bag (ryr) tx pc tarp bag (green) QTY. 1 1 1 tire tire 34-1-00003 tire swing tire 1 tx playcenter- standard box hardware st-1 st-2 st-3 st-4 st-5 st-6 st-7 st-8 st-9 st-10 st-11 st-12 st-13 st-14 st-15 st-16 st-17 st-18 ST-19 ST-20 40-1-00084 40-1-00083 40-1-00082 40-1-00081 40-1-00074 40-1-00073 40-1-00028 40-1-00064 40-1-00013 40-1-00012 40-1-00043 40-1-00061 40-1-00059 40-1-00056 40-1-00055 40-1-00069 40-1-00070 41-1-00025 40-1-00001 40-1-00002 3/4” uss flatwasher 1/2” uss flatwasher 3/8” uss flatwasher 1/4” uss flatwasher 1/2” split lockwasher 3/8” split lockwasher 1/2” hex nut 3/8” nylon insert locknut 1/2” x 7” carriage bolt 1/2” x 4 1/2” carriage bolt 3/8” x 5” hex bolt 3/8” x 5” lag bolt 3/8” x 3 1/2” lag bolt 1/4” x 4 1/2” lag bolt 1/4” x 3” lag bolt #14 x 1 1/4” pan phillips TS #14 x 2” Pan phillips ts 3/8” bolt cup 3/8” Acorn Nut 1/2” Acorn nut 22 22 51 47 22 4 22 4 20 2 4 11 36 20 12 2 15 4 4 22 TX Playcenter Standard Box tST-1 tST-2 tST-3 tST-4 tST-5 tST-6 tst-7 tst-8 tst-9 tst-10 53-1-00012 54-2-00004 54-2-00002 57-2-00004 57-2-00005 56-1-00012 59-1-00011 59-1-00013 37-1-00021 59-1-00008 21” x 63” Chain Ladder- (Yellow) 1 1/4” x 44” Playgrip Tube PC Coated 1 1/4” x 25” playgrip tube pc coated 1 1/4” playgrip safety handles 1 1/4” playgrip ladder handles ductile iron swing hangers spring clips 10mm x 100mm tree frogs plaque telescope tire swing eye bolt 1 1 1 4 2 2 5 1 1 3

5pc-11 5pc-12 5pc-13 5pc-14 5pc-15 5pc-16 40-1-00022 40-1-00056 40-1-00067 40-1-00077 40-1-00081 40-1-00111 2 1/2” coated deck screws 1/4” x 4 1/2” lag bolt 1/4” x 1 1/2” pan phillips m/s 1/4” x 7/16 4 prong t-nut 1/4” uss flatwasher 2” metal tap screw 56 24 32 32 56 4 Texan playcenter wood roof HARDWARE Item No. wr-17 wr-18 wr-19 wr-20 wr-21 wr-22 wr-23 wr-24 wr-25 wr-25 wr-26 Part Number 40-1-00083 40-1-00082 40-1-00081 40-1-00073 40-1-00026 40-1-00001 40-1-00115 40-1-00056 40-1-00055 40-1-00054 40-1-00020 Part Description 1/2” USS FLATWASHER 3/8” USS FLATWASHER 1/4” USS FLATWASHER 3/8” SPLIT LOCKWASHER 3/8” HEX NUT 3/8” ACORN NUT 3/8” X 5” CARRIAGE BOLT 1/4” X 4 1/2” LAG SCREW 1/4” X 3” LAG SCREW 1/4” X 2” LAG SCREW 1 5/8” COATED DECK SCREWS QTY. 4 4 38 4 4 4 4 24 2 14 210 uNIVERSAL rAIL hARDWARE(COUNT FOR ONE RAIL) RA-4 40-1-00022 2 1/2” COATED DECK SCREWS 20 Universal Deck Hardware DECK-5 40-1-00022 2 1/2” COATED DECK SCREWS 84

#UB1 17-4-00186 Universal PC Main Beam 107” QTY. 2 #UB2 16-4-00213 Uni. PC Center Post 88” QTY. 2 #UB3 16-4-00216 (L) Gusset Bracket 19” QTY. 5 #UB4 16-4-00217 (R) Gusset Bracket 19” QTY. 5 #UB5 17-4-00106 (L) PC Support Gusset 16” QTY. 2 #UB6 17-4-00107 (R) PC Support Gusset 16” QTY. 2 #UB7 16-4-00215 Universal Rope Block 11” QTY. 1 #UB8 12-4-00141 Universal Rail Bottom 25” QTY. 3 #UB9 16-4-00218 Universal Ent. Block 25” QTY. 1 #UB10 16-4-00214 Uni. PC. Corner Post 39” QTY. 4 #UB11 16-4-00223 Uni. PC. Top Joist w Swing Holes 125” QTY. 1 #UB12 16-4-00224 Uni. PC. Top Joist 125” QTY. 1

#TX-1 16-4-00220 TX PC Upper Rope Arm 105 1/2” QTY. 1 #TX-2 12-4-00146 TX PC Tarp Board 68” QTY. 2 #TX-3 12-4-00145 Universal Tarp Board 61” QTY. 1 #TX-4 16-4-00221 TX PC Ground Runner 71” QTY. 1 #TX-5 16-4-00219 TX PC Lower Rope Runner 107” QTY. 1 #TX-6 16-4-00222 TX PC Upper Acc. Arm 105 1/2” QTY. 1 5.4 Texan PC Bundle a. #5TX-1 16-4-00320 (L) PC Wood Step Ladder Leg 88 1/2” QTY. 1 #5TX-2 16-4-00321 Center Wood Step/ Chain Ladder Leg 88 1/2” QTY. 1 #5TX-3 16-4-00322 (R) PC Chain Ladder Leg 88 1/2” QTY. 1

#5TX-4 13-4-00066 Wood Step 18 1/2” QTY. 6 #5TX-5 16-4-00323 (R) PC Rockwall Ladder Leg 88 1/2” QTY. 1 #5TX-6 16-4-00324 (L) PC Rockwall Ladder Leg 88 1/2” QTY. 1 #5TX-7 11-4-00103 TX PC RW Board W/ Out Holes 43 1/2” QTY. 4 #5TX-8 11-4-00102 TX PC RW Board W/ Holes 43 1/2” QTY. 8 #5TX-9 11-4-00101 TX PC RW Board W/ Rope Hole 43 1/2” QTY. 1 Texan PC WOOD ROOF Bundle #WR-1 10-4-00348 TX PC Wood Roof Tarp Board” QTY. 1 #WR-2 12-4-00204 Uni. PC (L) Wood Roof Support 79” QTY. 2 #WR-3 12-4-00205 Uni. PC (R) Wood Roof Support 79” QTY. 2

#WR-4 19-4-00092 TX PC Wood Roof Board 68” QTY. 32 #WR-5 19-4-00093 TX PC WR Board Ripped 68” QTY. 2 #WR-6 12-4-00208 QC PC Wood Roof Runner 36” QTY. 4 #WR-7 12-4-00209 QC PC Wood Roof Runner 39 1/2” QTY. 4 #WR-8 10-4-00346 QC PC Wood Roof Center Support 36” QTY. 2 #WR-9 10-4-00347 QC PC Wood Roof Center Support 39 1/2” QTY. 2 #WR-10 20-4-00005 Universal Center Fan Board 15 1/4” QTY. 2 #WR-11 10-4-00209 Uni. PC Bottom Fan Board 62” QTY. 2 #WR-12 10-4-00212 Uni. PC Center Fan Board 20 1/4” QTY. 2 #WR-13 10-4-00210 Uni. PC Long (L) Side Fan Board 19” QTY. 2 #WR-14 10-4-00213 Uni. PC Long (R) Side Fan Board 19” QTY. 2 #WR-15 10-4-00214 Uni. PC Short (R) Side Fan Board 14” QTY. 2 #WR-15 10-4-00211 Uni. PC Short (L) Side Fan Board 14” QTY. 2

QTY. 3 RA-2 12-4-00141 Universal Rail Bottom QTY. 3 RA-3 15-4-00008 Universal Rail Picket QTY. 15 DECK Bundle DECK-1 12-4-00138 Deck Runner QTY. 4 DECK-2 13-4-00063 Deck Support QTY. 2 DECK-3 12-4-00139 Small Deck Board QTY. 8 DECK-4 13-4-00064 Large Deck Board QTY. 6

#5PC-6 37-1-00018 19” Ship’s Wheel- Yellow QTY. 1 #5PC-5 37-1-00019 19” Ship’s Wheel- Green QTY. 1 #5PC-1 36-1-00023 Large Rock (Multi Color) QTY. 16 #5PC-2 36-1-00024 Large Rock (Green) QTY. 16 #5PC-3 65-7-00017 14’ Yellow Rope QTY. 1 #5PC-4 65-7-00019 17’ Yellow Rope QTY. 3 #5PC-7 51-1-00031 43” Plastisol Coated Chain (Yellow) QTY. 1 #5PC-8 51-1-00032 43” Plastisol Coated Chain (Green) QTY. 1 #5PC-9 56-1-00015 Tire Swivel QTY. 1 #5PC-10 60-1-00006 20” Trapeze w/ 43” Chain- Yellow QTY. 1

#TB-1 61-8-00055 TX PC Tarp Bag- BYB QTY. 1 #TB-2 61-8-00056 TX PC Tarp Bag-RYR QTY. 1 #TB-3 61-8-00054 TX PC Tarp Bag- Green QTY. 1 Texan PC Standard Box #TST-1 53-1-00012 21 x 63” Chain Ladder- (Yellow) QTY. 1 #TST-2 54-2-00004 1 1/4” x 44” Tube PC Coated QTY. 1 #TST-3 54-2-00005 1 1/4” x 25” Tube PC Coated QTY. 1 #TST-4 57-2-00004 1 1/4” Playgrip Safety Handles QTY. 4 #TST-5 54-2-00004 1 1/4” Playgrip Ladder Handles QTY. 2 #TST-6 56-1-00012 Ductile Iron hangers QTY. 2 #TST-7 59-1-00011 Spring Clips 10 x 100mm QTY. 2 #TST-8 59-1-00013 Tree Frogs Plaque QTY. 1 #TST-9 37-1-00021 Telescope QTY. 1 #TST-10 59-1-00008 Tire Swing Eye Bolt QTY. 1

INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) Measurement taken from bottom of bolt head to the bottom of bolt USE THE RULER TO MEASURE YOUR BOLTS AND SCREWS. HARDWARE VIEWS SHOWN ABOVE ARE 1:1 SCALE AND CAN BE USED TO MATCH HARDWARE SIZES. #ST-1 40-1-00084 3/4” USS FLatwasher QTY. 22 #ST-2 40-1-00083 1/2” USS FLatwasher QTY. 22 #ST-3 40-1-00082 3/8” USS FLatwasher QTY. 51 #ST-4 40-1-00081 1/4” USS FLatwasher QTY. 47 #ST-5 40-1-00074 1/2” Split Lockwasher QTY. 22 #ST-6 40-1-00073 3/8” Split Lockwasher QTY. 4 #ST-7 40-1-00028 1/2” Hex Nut QTY. 22 #ST-8 40-1-00064 3/8” Nylon Locknut QTY. 4 #ST-9 40-1-00013 1/2” x 7” Carriage Bolt QTY. 20 #ST-19 40-1-00001 3/8” Acorn Nut QTY. 4 #ST-20 40-1-00002 1/2”Acorn Nut QTY. 22

INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) Measurement taken from bottom of bolt head to the bottom of bolt #ST-10 40-1-00012 1/2” x 4 1/2” Carriage Bolt QTY. 2 #ST-11 40-1-00043 3/8” x 5” Hex Bolt QTY. 4 #ST-12 40-1-00061 3/8” x 5” Lag Bolt QTY. 11 #ST-13 40-1-00059 3/8” x 3 1/2” Lag Bolt QTY. 36 #ST-14 40-1-00056 1/4” x 4 1/2” Lag Bolt QTY. 20 #ST-15 40-1-00055 1/4” x 3” Lag Bolt QTY. 12

INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) Measurement taken from bottom of bolt head to the bottom of bolt 5.4 TX PC Hardware Bag #ST-16 40-1-00069 #14 x 1 1/4” Pan Phillips TS QTY. 2 #ST-17 40-1-00070 #14 x 2” Pan Phillips QTY. 15 #ST-18 41-1-00025 3/8” Bolt Cup QTY. 4 #5PC-11 40-1-00022 2 1/2” Coated Deck Screw QTY. 56 #5PC-12 40-1-00056 1/4” x 4 1/2” Lag Bolt QTY. 24 #5PC-13 40-1-00067 1/4” x 1 1/2” Pan Phillips QTY. 32 #5PC-14 40-1-00077 1/4” x7/16 4 Prong T-Nut QTY. 32 #5PC-15 40-1-00081 1/4” USS Flatwasher QTY. 32 #ST-16 40-1-00111 2” Metal tap Screw QTY. 4

INSTALLER NOTE: (YOU MUST ASSEMBLE THIS PRODUCT IN ACCORDANCE WITH THESE ASSEMBLY INSTRUCTIONS. WHEN COMPLETE GIVE MANUAL TO OWNER.) Measurement taken from bottom of bolt head to the bottom of bolt #WR-17 40-1-00083 1/2” USS Flatwasher QTY. 4 #WR-18 40-1-00082 3/8” USS Flatwasher QTY. 4 #WR-19 40-1-00081 1/4” USS Flatwasher QTY. 38 #WR-20 40-1-00073 3/8” Split Lockwasher QTY. 4 #WR-21 40-1-00026 3/8” Hex Nut QTY. 4 #WR-22 40-1-00001 3/8” Acorn Nut QTY. 4 #WR-23 40-1-00115 3/8” x 5” Carriage Bolt QTY. 4 #WR-24 40-1-00056 1/4” x 4 1/2” Lag Bolt QTY. 24 #WR-25 40-1-00055 1/4” x 3” Lag Bolt QTY. 2 #WR-26 40-1-00054 1/4” x 2” Lag Bolt QTY. 14 #WR-27 40-1-00020 1 5/8” Coated Deck Screw QTY. 210 Rail Hardware #RA-4 40-1-00022 2 1/2” Coated Deck Screw QTY. 20

GIVE MANUAL TO OWNER.) Measurement taken from bottom of bolt head to the bottom of bolt DECK-5 40-1-00022 2 1/2” Coated Deck Screw QTY. 84

PARTS #5TX- 1- (L) Playcenter Wood Step Ladder Leg- (1) #5TX- 2- Center Wood Step/ Chain Ladder Leg- (1) #5TX- 3- (R) Playcenter Chain Ladder Leg- (1) #5TX- 4- 5 1/4” Wood Step- (6) Hardware #5PC- 12- 1/4” x 4 1/2” Lag Bolt- (24) #5PC- 15- 1/4” USS Flatwasher- (24) #5PC- 16- 2” Metal Tap Screw- (4) #TST- 2 - 1 1/4” x 44” Playgrip Tube PC Coated- (1) #TST- 3 - 1 1/4” x 25” Playgrip Tube PC Coated- (1) #TST- 1 - 21 x 63” Chain Ladder- (1) 5TX-1 5PC-15 5PC-12 5TX-4 5TX-2 TST-2 TST-1 5TX-3 TST-3 5PC-16

PARTS #TX-4 - Texan Playcenter Ground Runner- (1) #UB-3 - (L) Gusset Bracket- (1) #UB-4 - (R) Gusset Bracket- (1) Hardware #ST- 12 - 3/8” x 5” Lag Bolt- (3) #ST- 3 - 3/8” USS Flatwasher- (7) #ST- 13 - 3/8” x 3 1/2” Lag Bolt- (4) TX-4 UB-3 UB-4 ST-12 ST-3 ST-3 ST-13

(1) #5TX-6- (L) Rockwall Ladder Leg (1) #5TX-7- TX PC Rockwall Board W/ Out Holes- (4) #5TX-8- TX PC Rockwall Board W/ Holes- (8) #5TX-9- TX PC Rockwall Board W/ Rope Hole- (1) #5TX-10- TX PC Rockwall Board Blank- (1) Hardware #5PC-11- 2 1/2” Coated Deck Screws (56) #5PC-13- 1/4” x 1 1/2” Pan Phillips M/S- (32) #5PC-15- 1/4” USS Flatwasher- (32) #5PC-14- 1/4” x 7/16” 4 Prong T-Nut (32) #5PC-1 or 2- Large Rock- (16) 5PC-14 5TX-8 5PC-13 5PC-15 5PC-13 5TX-8 5TX-10 5TX-8 5TX-9 5TX-7 5PC-11

(1) #UB-3 - (L) Gusset Bracket- (1) #UB-4 - (R) Gusset Bracket- (1) Hardware #ST- 12 - 3/8” x 5” Lag Bolt- (2) #ST- 3 - 3/8” USS Flatwasher- (6) #ST- 13 - 3/8” x 3 1/2” Lag Bolt- (4) 12” Space TX-5 ST-12 ST-3 UB-3 UB-4 ST-3 ST-13

Spindles 3 1/2” Gap Main Assembly PARTS #RA-1- Universal Rail Top- (1) #RA-2- Universal Rail Bottom- (1) #RA-3- Universal Spindle- (5) #UB-1- Universal PC Main Beam- (2) Hardware #RA-4- 2 1/2” Coated Deck Screw- (20) #ST-20- 1/2” Acorn Nut- (4) #ST-9- 1/2” x 7” Carriage Bolt- (4) #ST-1- 3/4” USS Flatwasher- (4) #ST-2- 1/2” USS Flatwasher- (4) #ST-5- 1/2” Split Lockwasher-(4) #ST-7- 1/2” Hex Nut- (4) RA-1 RA-3 RA-2 RA-4 UB-1 ST-20 ST-7 ST-5 ST-2 ST-1 ST-9

(2) #UB-6- (R) Playcenter Support Gusset- (2) #UB-2- Uni. Playcenter Center Post- (2) #UB-10- Uni. Playcenter Corner Post- (4) Hardware #ST- 9- 1/2” x 7” Carriage Bolt- (6) #ST-1- 3/4” USS Flatwasher- (6) #ST- 2- 1/2” USS Flatwasher- (6) #ST-5- 1/2” Split Lockwasher- (6) #ST- 7- 1/2” Hex Nut- (6) #ST-20- 1/2” Acorn Nut- (6) #ST- 13- 3/8” x 3 1/2” Lag Bolt- (16) #ST -3 - 3/8” USS Flatwasher- (16) UB-5 UB-6 ST-3 ST-13 ST-9 ST-1 ST-2 ST-5 ST-20 ST-7

(4) Deck-2- Deck support- (2) Deck-3- Small Deck board- (8) DECK-4- Large Deck Board- (6) Hardware DEck-5- 2 1/2” Coated deck screw- (84) DECK-1 DECK-1 DECK-2 DECK-4 DECK-4 DECK-3 DECK-5 DECK-5 3 1/2” Gap 3 1/2” Gap 24 1/4” Gap

(2) Hardware #ST-14- 1/4” x 4 1/2” Lag Bolt- (8) #ST- 4- 1/4” USS Flatwasher (8) DECK ST-4 ST-14

(2) #UB-4- (R) Gusset bracket- (2) #UB-11- Uni. PC Top Joist W/ Swing Holes- (1) #UB-12- Uni. PC Top Joist- (1) Hardware #ST- 9- 1/2” x 7” Carriage Bolt- (6) #ST-1- 3/4” USS Flatwasher- (6) #ST- 2- 1/2” USS Flatwasher- (6) #ST-5- 1/2” Split Lockwasher- (6) #ST- 7- 1/2” Hex Nut- (6) #ST-20- 1/2” Acorn Nut- (6) #ST- 13- 3/8” x 3 1/2” Lag Bolt- (8) #ST -3 - 3/8” USS Flatwasher- (8) UB-12 UB-11 UB-4 UB-3 ST-20 ST-7 ST-5 ST-2 ST-1 ST-9 ST-13 ST-3

(1) #TX-6- TX PC Upper Accessory Arm- (1) Hardware #ST- 9- 1/2” x 7” Carriage Bolt- (4) #ST-1- 3/4” USS Flatwasher- (4) #ST- 2- 1/2” USS Flatwasher- (4) #ST-5- 1/2” Split Lockwasher- (4) #ST- 7- 1/2” Hex Nut- (4) #ST-20- 1/2” Acorn Nut- (4) #ST- 12 - 3/8” x 5” Lag Bolt- (4) #ST -3 - 3/8” USS Flatwasher- (4) TX-6 TX-1 ST-9 ST-1 ST-20 ST-7 ST-5 ST-2 ST-3 ST-12

(1) #UB-4- (R) Gusset Bracket- (1) #TST-6- Ductile Iron Swing Hangers- (2) Hardware #ST- 11- 3/8” x 5” Hex Bolt- (4) #ST-3- 3/8” USS Flatwasher- (8) #ST- 18- 3/8” Bolt Cup- (4) #ST-6- 3/8” Split Lockwasher- (4) #ST- 8- 3/8” Hex Nut- (4) #ST-19- 3/8” Acorn Nut- (4) #ST- 13 - 3/8” x 3 1/2” Lag Bolt- (4) ST-11 ST-18 ST-6 ST-19 ST-3 ST-8 TST-6 ST-3 ST-13 UB-4 UB-3

(1) #UB-8- Universal Rail Bottom- (3) Hardware #ST-14- 1/4” x 4 1/2” Lag Bolt- (6) #ST-4- 1/4” USS Flatwasher- (18) #ST-15- 1/4” x 3” Lag Bolt- (12) ST-4 ST-14 ST-14 ST-4 ST-4 ST-15 UB-8

#TX-3- Universal Tarp Board- (1) #5PC-10- 20” Trapeze Bar (Yellow)- (1) Hardware #ST-14- 1/4” x 4 1/2” Lag Bolt- (6) #ST-4- 1/4” USS Flatwasher- (6) ST-14 ST-4 TX-2 TX-3

In this step we are connecting the Rope Block on the Texan Playcenter Upper Rope Arm and the Texan Playcenter Lower Rope Runner. 1.) Thread the Rockwall Rope through the Rope Block and tie a knot. 2.) Tie 4 knots spaced evenly throughout the length of the Rockwall Rope. 3.)Place the Rockwall Rope through the Texan Playcenter Lower Rope Runner on the back side. In this step we are connecting the Rope Ladder to the Texan Playcenter Upper Rope Arm and the Texan Playcenter Lower Rope Runner. 1.)Thread the Ladder Ropes through the Texan Playcenter Upper Rope Arm and tie knots. 2.) Slide a Rope Rung up the Ladder Ropes with about 10”-11” between bottom of the Texan Playcenter Upper Rope Arm and Rope Rung, tie a single knot on each rope, directly below item Rope Rung. 3.) Repeat step 2 for the remaining Rope Rungs with about 10”-11” between each Rope Rung.

the corner. Tap the snap with a blunt object, leaving an indention of the snap in the wood. Repeat this process until all the snaps have been indented in the wood on both sides of the Playcenter. (Figure B.)- Using the indentions you just made with the snaps, take the 5/8” PHILLIPS SCREW SNAPS and drill one into each indention.

Take the corner of the VINYL TARP and start placing the snaps on the PHILLIPS SCREW SNAPS. Fold the VINYL TARP over the top of the UNIVERSAL TARP BOARD. Pull tight and place the snaps on the PHILLIPS SCREW SNAPS. PARTS #WR-4- TX PC Wood Roof Board- (16) #WR-6- QC PC Wood Roof Runner- (4) Hardware #WR-26- 1 5/8” Coated Deck Screws- (64) #WR-26 Repeat this step one more time for 2, 8 Board Roof Panels 5“ Gap #WR-4 #WR-6 Place WR-6 to the inner lip of the 1st Wood Roof Board

PARTS #WR-9- QC PC Wood Roof Center Support- (2) #WR-7- QC PC Wood Roof Runner #2- (4) #WR-5- TX PC Wood Roof Board Ripped- (2) #WR-4- TX PC Wood Roof Board- (16) Hardware #WR-26- 1 5/8” Coated Deck Screws- (42) Repeat this step one more time for 2, 8 Board Roof Panels #WR-9 #WR-26 8 Board Roof Panel 9 Board Roof Panel Repeat this step one more time for 2, 9 Board Roof Panels #WR-26 13/16“ Gap #WR-4 5“ Gap #WR-5

PARTS #WR-8- QC PC Wood Roof Center Support- (2) #WR10- Universal Center Fan Board- (2) #WR-11- Universal PC Bottom Fan Board- (2) Hardware #WR-26- 1 5/8” Coated Deck Screws- (13) #WR-26 Repeat this step one more time for 2, 9 Board Roof Panels 32 1/4“ Gap #WR-8 Wood Roof Fan Repeat this step one more time for 2, Wood Roof Fans #WR-26 #WR-10 #WR-11 19 1/8” Gap

PARTS #WR-12- Universal PC Center Fan Board- (2) #WR-13- Uni. PC Long(L) Side Fan Board- (2) #WR-14- Uni. PC Long(R) Side Fan Board- (2) #WR-15- Uni. PC Short (R) Side Fan Board- (2) #WR-16- Uni. PC Short (L) Side Fan Board- (2) Hardware #WR-26- 1 5/8” Coated Deck Screws- (13) #WR-26 #WR-12 #WR-14 #WR-15 #WR-16 #WR-13 #WR-26 Repeat this step one more time for 2, Wood Roof Fans 25” Gap

PARTS #WR-1- TX PC Wood Roof Tarp Board- (1) #WR-2- Uni. PC (L) Wood Roof Support- (2) #WR-3- Uni. PC (R) Wood Roof Support- (2) Hardware #WR-23- 3/8” x 5” Carriage Bolt- (4) #WR-25- 1/4” x 3” Lag Bolt- (2) #WR-17- 1/2” USS Flatwasher- (4) #WR-18- 3/8” USS Flatwasher- (4) #WR-20- 3/8” Split lockwasher- (4) #WR-21- 3/8” Hex Nut- (4) #WR-22- 3/8” Acorn Nut- (4) #WR-19- 1/4” USS Flatwasher- (2) #WR-3 #WR-2 #WR-22 #WR-20 #WR-21 #WR-18 #WR-23 #WR-17 #WR-1 #WR-25 #WR-19

PARTS Wood Roof 8 Board Panels- (2) Wood Roof 9 Board Panels- (2) Hardware #WR-24- 1/4” x 4 1/2” Lag Screw- (24) #WR-19- 1/4” USS Flatwasher- (24) #WR-24 #WR-24 #WR-19 #WR-19 8 Board Roof Panel 9 Board Roof Panel

(1) Wood Roof Fan- (2) Hardware #ST-12- 3/8” x 5” Lag Bolt- (2) #ST-3- 3/8” USS Flatwasher- (2) #WR-25- 1/4” x 2” Lag Screw- (14) #WR-19- 1/4” USS Flatwasher- (14) ST-12 ST-3 Slide Install #WR-FAN #WR-19 #WR-25 Wood Roof Fan

PARTS #TST-4- 1 1/4” Playgrip Safety Handles- (4) Hardware #ST-16- #14 x 1 1/4” Pan Phillips- (11) #ST- 4- 1/4” USS Flatwasher- (3) ST-16 ST-4 ST-16

Ships Wheel Install PARTS #TST-5- 1 1/4” Playgrip Ladder Handles- (2) #5PC-5 or 6- 19” Ships Wheel w/ Hardware- (1) Hardware #ST-17- #14 x 1 1/4” Pan Phillips- (4) ST-17 TST-5

Using a pencil or pen mark the holes in the center of the deck. Drill Marked Holes from previous step using a 9/16” bit. PARTS Pencil- (1) 9/16” Drill Bit- (1)

PARTS #5PC-9- Tire Swivel- (1) Hardware #ST-10- 1/2” x 4 1/2” Carriage Bolt- (2) #ST-1- 3/4” USS FLatwasher- (2) #ST-2- 1/2” USS Flatwasher- (2) #ST-5- 1/2” Split Lockwasher- (2) #ST-7- 1/2” Hex Nut- (2) #ST-20- 1/2” Acorn Nut- (2) ST-10 ST-1 5PC-9 ST-2 ST-5 ST-7 ST-20