VOCOlinc L3 Manual 

multi-color LED Light Bulb that can be controlled wirelessly via iOS or Android smartphones and tablets, no hub required. You can customize your personal lighting using the VOCOlinc app from anywhere with an active internet connection. Specifications Input: AC120V, 60Hz or AC220-240V, 50Hz / 60Hz Base type: E26 or E27 Rated power: 9.5W LED color range: 16 million colors with cool to warm whites Color temperature: 2200K – 7000K (including 2200K, 2500K, 2700K, 3000K, 3500K, 4000K, 5000K, 5700K, 6500K, 7000K) Luminous flux: 850 lumens Beam angle: 220 degrees E26 or E27 Base ll manuals and user guides at

Operation frequency band(s): 2412~2462MHz for E26, 2412~2472MHz for E27 Max. transmitted RF power: 12±1dBm What’s Included L3 Smart Wi-Fi A21 or A67 Light Bulb User Manual L3 SmartGlow Light Bulb LED status Features: 16 million colors Works with Apple HomeKit Works with Amazon Alexa Works with the Google Assistant Remote Access Status Turning on the first time L3 Searching Wi-Fi Pairing Device added successfully Identifying the light bulb White light at 5% brightness White light at 5% brightness White light at 50% brightness White light at 5% brightness quickly blinks 5 times Firmware update completed Blinks twice ll manuals and user guides at

you may have. To reset it to factory defaults: 1. Turn the light switch controlling the bulb to the OFF position. 2. Flip the light switch on and off 3 times. Time lag between each cycle must not exceed 5 seconds. The Smart light bulb will blink three times once reset is completed. Note: all connection data will be cleared. SmartGlow Light Bulb L3 must be removed from the app and then added back again. Factory Resetting * If you set the brightness to 0% before turning off the light switch, the smart light bulb will resume to 5% brightness as soon as you turn on the light switch again to indicate that it is in good shape. Safety Warnings WARNING: RISK OF ELECTRIC SHOCK OR BURNS. Switch OFF the light switch controlling the bulb and WAIT for the bulb to cool down before attempting to change it DO NOT install the Smart Wi-Fi LED Bulb with wet hands or when standing on wet or damp surfaces Not suitable for use with standard in-wall dimmers. Dimmable via the app only Suitable for use in operating environment between 0°C and 40°C (32°F and 104°F) This device is not intended for use with emergency exit luminaires System Requirements Mobile device running iOS12.0+ or Android OS4.3+ Existing Wi-Fi network Stable Internet with good signal strength ll manuals and user guides at

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Caution: FCC Declaration For lamps with a weight significantly higher than that of the lamps for which they are a replacement, attention should be drawn to the fact that the increased weight may reduce the mechanical stability of certain luminaires and lampholders and may impair contact making and lamp retention. NOT FOR EMERGENCY LIGHTING For indoor use only DO NOT disassemble DO NOT clean with liquid Use in Dry Locations only Only use the control provided with or specified by these instructions to control this lamp. This lamp will not operate properly when connected to a standard (incandescent) dimmer or dimming control ll manuals and user guides at

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. In order to avoid the possibility of exceeding the ISEDC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Caution: IC Declaration EU declaration of conformity Hereby, VOCOlinc declares that the radio equipment SmartGlow Light Bulb is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.vocolinc.com ll manuals and user guides at