Tranberg TEF 2441 Operation & User’s Manual

E-mail: [email protected] | www.tranberg.com Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: (45) 75 85 83 80 E-mail: [email protected] | www.tranbergsystems.com TEF 2441 LUMINAIRE USER MANUAL IMPORTANT Read this instruction carefully before installing the luminaire 240A4831 TUM 1009 Rev. A 03.01.17

INTRODUCTION Thank you for purchasing this product! For installation, maintenance and assurance of a long life of this product, please follow this manual. CONTENT IN BOX The product is fully assembled, and ready for installation. SAFETY PRECAUTIONS Note that changes made to the product and/or installation of components which do not conform to the approval, may be a safety violation. The manufacturer will in no circumstance be held responsible for such activity. For your health and safety, always use safety gear suited for the task. Be certain to follow codes, regulations and/or specifi c procedures that are related to the installation. TOOLS REQUIRED Regular tools required for installation: • 10mm wrench - when installing the luminaire. • 32mm wrench - when installing the cable gland • 30mm wrench - when installing the lock nut. • 25mm wrench –when tightening the pressure nut. • PZ 2 screwdriver for assemble/dissemble the globe • 3mm straight screwdriver for terminal to connect the lighting. • 5mm straight screwdriver for earth screw. Do not use powertools when fastening globe! MAINTENANCE INSTRUCTIONS The luminaire should be inspected according to Company routines. The manufacturer suggests regular check for water intrusion/condensation which should be removed immediately. Check the drain plug / drain hole function. When cleaning, use only mild detergents. Alcohol or petroleum based products may damage lens, paint or plastic components. ELECTRICAL INSTALLATION The luminaire is factory confi gured with grommet kit 3C, suitable for cable diameters ranging from 8.5 mm to 13.5 mm. For cable diameters ranging from 13.0 mm to 17.0 mm, please ensure to replace the installed grommet kit with kit 3D. Cable entries should be tightened properly. Do not use execessive force, as this may disalign the grommet components and lead to water intrusion. Make sure electrical connections are safe and reliable. RUBBER SEAL Cable diameter Size Part No. 8,5 - 13,5mm Ø23/13x8mm 5002 0124 13 - 17mm Ø23/16x8mm 5002 0125 Be sure to install the cable in a way wich prevents water to penetrate into the enclosure through the cable gland, Also make sure to use the correct rubber seal when you install the luminaire APPLICATIONS • Signal lighting • Obstacle marking APPROVALS NA

Before replacing the globe assembly, please review the fol- lowing: • Verify that the grommet kit used match the cable diameter. • Cables should have a bend before entering the cable gland, which will avoid water intrusion into the luminaire. • An unused cable gland should be replaced with a blind plug. Ensure the globe gasket is clean and properly aligned around the bottom of the globe. Then carefully position the globe over the PL-C light source and into the circular opening in the luminaire base. Slightly tighten two opposite screws, then repeat with the other two opposite screws. This ensures that the globe is positioned evenly and the pressure on the globe gasket is distributed evenly. Tighten all four screws until the globe is fi rmly positioned. Power tools should under no circumstances be used! WIRING DIAGRAM COMPLETE THE INSTALLATION

E-mail: [email protected] | www.tranberg.com Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: (45) 75 85 83 80 E-mail: [email protected] | www.tranbergsystems.com TEF 2441 LUMINAIRES USER MANUAL TECHNICAL DATA Material: Acid proof stainless steel, powder coated RAL 9010 Globe : Polycarbonate Light output: >10 candela red Power comsumption: Max. 20 Watt IP-rating: IP66 Standard cable entries: 3 x M25 stopping plug Weight: 3,8 kg. Tamb: -20°C to +40°C For use in zone: Safe area SPARE PARTS Description Part No. Globe red, without gasket 5044 2006 Globe gasket, silicone 5001 0021 Globe retainer ring 2547 Fluorescent tube, PLC 13W/84 9400 060 Cable gland, E704/CD/M25 9147 200 Stopping plug, M25 EExe 7947 304 Drain plug with lock nut, M25 EExe 7302 106