Vivotek AF101 Quick Start Manual

(AM812+AM813+AM814) (for Social Distancing Control) Quick Installation Guide Package Contents Hardware Installation 1 2 AM812 AM814 Hex wrench AM813 AM812 Cushion AF101 AM813 AM812 AM814 1. AM812, AM813, AM814 2. Screws, 1x T10 torx star L wrench, 1x hex wrench * The AB101 edge computer and AF101 Thermal reader come in other packages. The wall- mount bracket and middle bracket come with the AF101. The middle bracket is not used. NOTE: 3 When cables are in place, assemble the top section, and drive the flathead screws on the sides. The AF101 configuration can not be exposed to direct sunlight. Assembly the AM814 base plate and AM812 using 2 hex sunkhead screws. Assemble the top section (AM813) with the stand. Pull the cables (RJ45 Ethernet, USB, and 12V power jack) through the bottom of the AM813 and through the opening in the center. You can put the AM813 on top of the stand and place a piece of clothe underneath to avoid damaging the aluminum surface. 4 Secure another 2 screws from the other side. 5 Remove the protective sheet from the wall-mount bracket. AF101 T10 torx wrench 6 Lay the reader on a clean surface. Remove the bottom mounting plate using the T10 torx wrench. Keep the anti-tamper screw for later use. Screw tab, this side up Securing tab Bracket from reader 7 Install the bracket to the wall-mount bracket by driving 4 cross-head sunkhead screws. 8 Install the bracket assembly to the stand by driving 4 small cross-head hex screws. Please also pull the cable through the center opening.

on the stand. If preferred, connect the DIDO cable as well. When done, push all cabling into the center hole. Reader Securing tab Stand bracket 10 After all cabling connectors passed the center hole, flush align the reader with the bracket, and slide down. The securing tab in the center will secure the reader’s position. You can observe from the side while sliding the reader against the bracket. 11 From the bottom of the reader, secure the installatioin using the T10 anti-tamper screw you previously removed. Efhernet 12V power 12 Connect an Ethernet cable and 12V power from the included power adapter to the back of the stand. Pass each connector one by one into the center hole. Make sure the connectors pass the center hole. Note that the additional USB cables are currently not used. HDMI/DP Monitor Ethernet Camera 04 Camera 05 Camera 07 Camera 08 Camera 09 PoE switch Client PC IPC Counting camera(s) Thermal reader 10.0.0.140 10.0.0.141 13 Connect your devices in the Covid Defender configuration to a local network. 10 . 0 . 0 . 145 14 Change your client computer’s IPv4 address to be within the same network of the IPC (10.0.0.140). 15 Open a browser session to 10.0.0.140. Use the default user/password: admin/ admin. You can now start to configure the defender’s settings. Refer to the user documentation of your Covid Defender devices for more information. VIVOTEK INC. 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282|F: +886-2-82455532| E: [email protected] VIVOTEK USA, INC. 2050 Ringwood Avenue, San Jose, CA 95131 |T: 408-773-8686|F: 408-773-8298|E: [email protected] VIVOTEK Europe Zandsteen 15, 2132 MZ Hoofddorp Delta Electronics T: +31 (0)20 800 3817 | E: [email protected] All specifications are subject to change without noice. Copyright © 2020 VIVOTEK INC. All rights reserved. You can access, configure, or change the devices’ IP addresses if necessary. When necessary, use ground anchors to secure the base plate on the floor. 16 Remove the protective sheet on the reader.