Vitek Transcendent Series Quick Start Manual

Recognition WDR IP Motorized Bullet Camera QUICK START GUIDE FEATURES: • Advanced Starlight Technology Offers Dramatically Higher Sensitivity to Light Producing Color Images in Very Dark & Night Scenes • 1/2.8” 2.0 Megapixel CMOS Image Sensor • 1080P (1920 × 1080), 720P (1280 × 720), D1, CIF, 480 × 240 • 7~22mm @ F1.6 Motorized Varifocal Lens • Field of View - H: 44°~17.6°; V:25.6°~10°; D: 49.7°~20.2° • 6 Matrix IRs with up to 325’ IR Range • True Wide Dynamic Range (120db) • True Mechanical Day/Night function by ICR • XD-DNR (3D & 2D Digital Noise Reduction) • License Plate Recognition (LPR), Abnormal Video, Scene Change • LPR Snapshot: Overview and Cutout of Plate, White List: 10,000 • LPR Capture Speed Range: 0-44m/h (0~70km/h) [Installation Dependent] • Smart H.265 / H.265+ / H.265 / Smart H.264 / H.264+ / H.264 / MJPEG Compression • MicroSD Card Slot for Local Recording (Up to 128GB) • One Channel Audio Input + One Channel Audio Output* • One Channel Alarm Input + One Channel Alarm Output • Remote Viewing via CMS, Internet Explorer, and iOS & Android Apps • ONVIF Compliant • IP67 Weather Resistance • Wall Mount Included and Optional Junction Box VT-TJB01 Available • 12VDC & PoE (Power over Ethernet) Operation • 3-Year Warranty *Please research local, state and federal laws regarding audio surveillance. PLEASE NOTE: Complete User Guide, Software, Tools, and Updates are available online. Scan the QR Code or visit: http://www.vitekcctv.com/Downloads

First connect the weather resistant cap to an ethernet patch cable, then connect the cameras ethernet adaptor. If not powering the camera with PoE, also connect the power cable to an approved 12VDC power supply. 1. Loosen the nut from the Weather Resistant Network Coupler, 2. Run ethernet cable through coupler, then attach a RJ-45 connector. 3. Tighten the nut and coupler for a weather resistant seal. weather resistant cap

strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows: 1. Attach the drill template to the place where you want to install the camera, then drill 4 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template 2. Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base. then secure the mounting base to the ceiling or wall with screws. 2.54” 2.54” .2”

tighten the mount lock to secure the viewing angle adjustments. 4. Open the cover of the camera as shown in the following figure, then insert a MicroSD card. Insert MicroSD Card 5. Re-install the cover back on the camera and close it with screws. Be sure to re-install the cover evenly.

IP-Tool or directly in a web browser. Accessing the Camera Using the IP-Tool 1. Make sure the camera and PC are connected to the LAN. 2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Soft- ware/Transcendent-IPTool_v2.0.2.zip, then install on the PC. Open the installed application. 3. Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation. For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera should be changed to 192.168.13.X. After modifying, please input the password of the administrator and click “Modify” button to modify the setting. ** Default admin password: “123456". MENU IP Camera Network Cable Network Cable Switch Router Computer

browser to connect IP-CAM . IE browser will download the Active X control. After downloading, a login window will pop up as shown below: Input the user name and password to log in. Default user name: admin / Default password: 123456. Directly Access Through a Web Browser The default network settings are as shown below: IP address: 192.168.226.201 HTTP: 80 Subnet Mask: 255.255.255.0 Data Port: 9008 Gateway: 192.168.226.1 You may use the above default settings when you log in the camera for the first time. 1. Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window. Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC.

confirm. The IE browser will download Active X control. 3. After downloading Active X control, the login dialog box will pop up. 4. Input the default username and password and then enter to view. WAN Configuration Access the camera by the router or virtual server for example. 1. Make sure the camera is connected to the LAN; Then log into the camera via LAN and go to System Congfig→Network Config→Port menu to set up the port number. 2. Enter System Config→Network Config→IP Address menu to modify the IP address. 4. Open the web browser and input its WAN IP and HTTP port to access the IP-CAM. 3. Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”. 5. For additional setup, features and functions, please scan the QR code on the front page of this quick guide and download the complete manual.

Image Size 2 MegaPixel (1920 × 1080) Resolution 1080P (1920 × 1080), 720P (1280 × 720), D1, CIF, 480 × 240 Min. Illumination 0.0026 [email protected],AGC ON; 0 lux with IR / 0.005 [email protected], AGC ON; 0 lux with IR Electronic Shutter 1 / 25 s ~ 1 / 100000s Lens 7~22mm Motorized Varifocal Lens @ F1.6 IR LEDs, Distance 6 Matrix Style IRs, Up to 325’ Video Compression Smart H.265/(+), H.265, Smart H.264/(+), H.264, MJPEG Audio Compression G.711A / G.711U Main-Stream 60Hz: 1080P/720P (1~30fps); HFR Mode: 1080P/720P (60Hz: 1~60fps; 50Hz: 1~50fps) 50Hz: 1080P/720P (1~25fps) Sub Stream, Third Stream 60Hz: 720P/D1/CIF (1~30fps); 50HZ: 720P/D1/CIF/480x240 (1~25fps) Bit Rate / Type 64 Kbps ~ 6 Mbps / VBR + CBR Wide Dynamic Range 120dB Digital Noise Reduction XD-DNR (3D & 2D-DNR) Other Features Backlight / Hightlight Compensation, Defog Image Setting ROI, Saturation, Brightness, Chroma, Contrast, Sharpen, NR; Adjustable through client software or browser Analytics License Plate Recognition, Abnormal Video, Scene Change Alarm Smart Alarm 1 Ch. Alarm In + 1 Ch. Alarm Out* Motion Detection, SD Card Error, SD Card Full General Functions Watermark, IP Filter, Video Mask, Illegal Login Lock Region of Interest (ROI) Each ROI to be configured separately Network RJ45 Hardware Reset Yes Analog Video Output No Audio 1 Ch. Audio In + 1 Ch. Audio Out* Local Storage Built-in Micro SD card slot up to 128GB Remote Viewing CMS / Web Browser / Mobile (iOS/Android) Supported Browsers Internet Explorer, Chrome and Firefox with IE Tab Interface Protocol ONVIF Weather IP67 Power Input Consump. (12VDC, PoE) 12VDC / PoE (12VDC) 210mA (IRs Off) / 545mA (on), (PoE) 4W (IRs off) / 7.8W (on) Working Environment -22°~140° / < 95% Humidity Weight Dimensions L x W x H 36.69.5 oz. / 2.29 lbs. / 1.04kg 3.95” x 3.54” x 11.00” (100.3mm x 89.9mm x 279.5mm) DETAILED SPECIFICATIONS - VTC-TNB2LPR

Transcendent Series Network Recorders Supporting Advanced Analytics and PoE! VT-TJB01 Optional Junction Box for Use with Select Transcendent Bullet Cameras including VTC-TNB2LPR Accessories Recorders VT-TPLMT Transcendent Universal Pole Mount VT-TCNMT Transcendent Univeral Corner Mount

Reduce Costly Cable Installation! VT-WAP1150 and VT-WAP2150 High Speed 5.8GHz DIP AP / CPE Wireless Bridge w/ 8MB Storage, 64MB RAM, 150MBps transmission, and Point-to-Multi-Point (P2MP) Topology With high speed transmission of 150Mbps and a wireless range of 3000ft. (VT-WAP1150) and 1.25 miles (VT-WAP2150) these products eliminate the need for expensive and troublesome long- distance cables in areas where CCTV monitoring and rigorous surveillance take place. These small, lightweight and durable units are easy to install and easy to use with an innovative and straitghtforward 10-button plug-and-play dip switch that facilitates the creation of a robust wireless network without a computer. Set-up can be simply configured for point-to-point or point-to-multipoint topology depending on the application, with up to 128 IP group configurations! VT-WAP1150 VT-WAP2150

WWW.VITEKCCTV.COM Version 1.0 Aug 2020 LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller. The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning. The product must not have been tampered with in any way or the guarantee will be considered null and void. This guarantee does not affect your statutory rights. Contact your local VITEK Reseller should servicing become necessary. VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.