Sharp UX-108 Service Manual

UX-108DE [2] TEL/LIU PWB circuit 1/2 1 2 6 4 3 5 B D E F G I H C A 1 2 6 4 3 5 B D E F G I H C A N.M. JP5 JP106 JP105 JP101 JP3 JP4 ~ ~ + – – + – + +5V – + – + – + +5V – + +24VA +5V +5V +24VA IC101 2904 IC102 1458 C107 0.1 C118 0.1 C5 47/25 VREF-A VREF C121 0.1 C131 0.1 C123 1 R140 30K R132 20K C122 1 IC103 1458 PC5 R134 R127 C117 N.M. CNLIUA-2 TEL IN VREF R128 S D G C115 N.M. R125 24K R126 8.2K C9 2.2/50 IC102 1458 R136 56K C116 3300P R135 3.3K R131 2.2K R130 150 DG DG C6 2.2/50 D4 1SS133 D3 1SS133 L8 TR0703-600Y L7 TR0703-600Y DG DG Q101 BCR113 L6 TR0703-600Y C125 2200P ...

Fig. 10 Wire treatment 10 Parts list (Fig. 10) 1 Band 5 2 Screw (3×6) 2 3 Screw (4×6) 1 4 UL tape 1 5 Core (F2064) 1 6 Core (F2063) 1 7 Band (100mm) 1 No. Part name Q’ty 2 3 Rib Power supply PWB TEL/LIU PWB AC cord ARG cable OK NG Head earth cable Cam switch cable Cam switch cable 1 1 7 7 100 10mm 20 5mm Head, head earth and panel cable Head cable Motor cable Binding the cable(Head cable/ Head earth cable/CIS cable/ panel cable/motor cable/cam switch cable) Head cable and head earth cable Head earth cable Head cable Operation panel PWB Pa ...

UX-108DE 4. Clearing a jammed document If the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try press- ing the START key. If it doesn’t feed out, remove it as follows: Important: Do not try to remove a document without opening the op- eration panel. This may damage the feeder mechanism. 1 Pull the release marked PANEL RELEASE toward you and open the operation panel. 2 Remove the document. 5. Clearing jammed fax paper 1 Pull the release marked PANEL RELEASE toward you and open the operation panel. 2 Remove th ...

1 Reserved 0 2 Reserved 0 3 Reserved 0 4 Reserved 0 5 Reserved 0 6 Reserved 0 7 Reserved 0 8 Reserved 0 1 Reserved 0 2 Reserved 0 3 Reserved 0 4 Reserved 0 5 Reserved 0 6 Reserved 0 7 Reserved 0 8 Reserved 0 1 Reserved 0 2 Reserved 0 3 Reserved 0 4 Reserved 0 5 Reserved 0 6 Reserved 0 7 Reserved 0 8 Reserved 0 1 Reserved 0 2 Reserved 0 3 Sender’s phone number setting Cannot change Change allowed 0 4 Reserved 0 5 Reserved 0 6 Summer time setting No Yes 0 Ringer volume Off Low Middle High OPTION 7 No. 7 0 0 1 1 1 8 No. 8 0 1 0 1 0 Speaker volume Low Low Middle High OPTION 1 N ...

4. How to make soft switch setting To enter the soft switch mode, make the following key entries in sequence. Press FUNCTION 9 8 7 START START Press FUNCTION key. Press key. Press key. Bit1 - 8 are set. Soft SW-A2 - SW-L2 are set. S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A2 = 0 0 0 0 0 0 0 0 S F T SW-L2 = 0 0 0 0 0 0 0 0 Press key during setting. To finish the settings halfway between SW-A1 and ...