Zenith C27C41T Operating Manual & Warranty

o p e r a t i n g g u i d e / w a r r a n t y t a b l e o f c o n t e n t s p a g e 5  Copyright 2000, Zenith Electronics Corporation. machine numbers C27C41 C32C41 C36C41

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. RECORD YOUR MODEL NUMBER (Now, while you can see it) The model and serial number of your new TV are located on the back of the TV cabinet. For your future convenience, we suggest that your record these numbers here: MODEL NO.____________________________________ SERIAL NO.____________________________________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN B-WARN-DV-1 7/98 P A G E 2 ©Copyright 2000 Zenith Electronics Corporation

Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. Observing the simple precautions discussed in this operating guide can help you get many years of enjoyment and safe operation that are built into your new product. This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association. (Continued on next page) 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Follow Instructions All operating and use instructions should be followed. 3. Retain Instructions The safety and operating instructions should be retained for future reference. 4. Heed Warnings All warnings on the product and in the operating instruc- tions should be adhered to. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Water and Moisture Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 7. Accessories Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 8. Transporting Product A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 9. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. 10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Line-Cord Polarization This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. PORTABLE CART WARNING IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page) 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 15. Lightning For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service Unplug this product from the wall outlet and refer servic- ing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance. 21. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Grounding Conductor (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) Ground Clamp Electric Service Equipment Example of Grounding According to National Electrical Code Instructions NEC - National Electrical Code IMPORTANT SAFETY INSTRUCTIONS

Turn to the next page to set up your Entertainment MachineTM Table Of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . 3 - 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Step 1. Hook Up TV Hookup Directory . . . . . . . . . . . . . . . . . . . . . . . . . 6 TV and other Equipment Hookups Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . 9 Cable Service with VCR . . . . . . . . . . . . . . . . . . . . 10 Super VHS VCR/Digital Video Disk Player . . . . . . . . 11 External Audio Connections . . . . . . . . . . . . . . . . . 12 Step 2. Channel Search and Reception Setup EZ Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 (Select Antenna, or cable service and perform channel search) Remote Control TV Mode Key Functions . . . . . . . . . . . 14 Remote On-Screen Menu Operation . . . . . . . . . . . . . . 15 Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . 16 Selecting Viewing Sources . . . . . . . . . . . . . . . . . . . 17 On-Screen Menus/Displays Overview . . . . . . . . . . . . . 18 On-Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . 19 Step 3. Customize Your TV’s Features Setup Menu (Starts with page 13, EZ Program) EZ Program . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Add/Del/Surf . . . . . . . . . . . . . . . . . . . . . . . . . . 20 EZ Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Captions, Captions/Text . . . . . . . . . . . . . . . . . . . 22 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Source Menu Select Main Picture and PIP sources . . . . . . . . . 24 Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Contrast, Brightness, Color, Tint, Sharpness, Color Temp: (Cool, Warm), EZ Picture: (Custom, Normal, Movie, Digital Pres, Video Game, Sports, Weak Signal, Night Time). Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Bass, Treble, Balance, Audio Mode: (Stereo, Mono, SAP), Front Surround, EZ SoundRite, Speakers, EZ Sound: (Custom, Normal, Stadium, News, Music, Theater). Parental Control Menu . . . . . . . . . . . . . . . 27 - 28 - 29 Restricts viewer programming. Special Menu EZ Timer Sleep Timer, On Time, Off Time, On/Off Timer . . . 30 Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . 31 XDS Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 PIP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Picture-in-Picture Overview and Explanation 34 - 35 EZ Demo (On-screen menus overview) . . . . . . . . . . 36 EZ Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Remote Control Multi-Product Usage Programming 38 - 44 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Trouble Shooting . . . . . . . . . . . . . . . . . . . 46 - 47 - 48 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Zenith Accessory Products . . . . . . . . . Inside Back Cover Warranty . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover Features on this TV also include: PIP - 2-Tuner Picture-in-Picture, see page 34. Programmable Remote Control - Remote may control up to 7 products, see page 38. Extended data service (XDS) shows in-depth program information, see page 32. EZ Features: Designed to make your viewing experience less work; see the EZ Help menu on page 3. EZ Program Finds channels in your area automatically. EZ Clock Sets the time in the TV’s clock. EZ Picture Customizes video level settings. EZ Sound Adjusts sound based on program. EZ SoundRite Maintains and even sound level during programming volume variances. EZ Timer Sets times to turn TV on/off automatically. EZ Mute Displays Closed Captions/Text selection when TV sound is mute, while picture remains. EZ Demo Shows menus and displays on this TV. EZ Help Offers solutions to common problems on one convenient menu. Note: Design and specifications are subject to change without prior notice. Entertainment MachineTM is a trademark of Zenith Electronics Corporation.

If you are using an antenna and no other equipment, go to . . . . . . . . . . . . . . . . . . page 7 If you subscribe to cable service and use no other equipment, go to . . . . . . . . . . . . . page 8 If you are using an antenna and have a VCR, go to . . . . . . . . . . . . . . . . . . . . . . . page 9 If you subscribe to cable service and have a VCR, go to . . . . . . . . . . . . . . . . . . . . . page 10 This page directs you to the appropriate page for hook up of your Entertainment Machine IMPORTANT!! Use this page to decide where you need to begin your setup. First, find the line below that best describes what you want to do, then go to that page number. Note: Design and specifications are subject to change without prior notification. Cable TV wall jack Cable box In Out Cable TV wall jack Cable box In Out Antenna only Cable only Antenna with VCR Cable and VCR S-VHS/DVD/Stereo If you have a Super VHS VCR, a DVD Player, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11 If you want to connect Audio equipment, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12

The wire that comes from an off air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of your TV. 300-75 OHM ADAPTER A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end. Hook Up an Over the Air Antenna 206-3529 P A G E 7 Connect an off air antenna to your Entertainment Machine Hook up your Entertainment Machine, see diagrams at right. Remove the back of the remote and put in two AAA batteries. Plug in your TV. Do not plug it into a switched outlet. Go to page 13 to EZ Program your Entertainment Machine. RF coaxial wire (75ohm) Antenna Typical TV back TV back panel (expanded view) Antenna / Cable Typical TV back Flat wire (300 ohm) Antenna 300/75 ohm Adapter TV back panel (expanded view) Antenna / Cable If you have a 75 ohm RF cable, then you don’t need any adapters! Remember, when screwing RF cables onto jacks, clockwise tightens, and counterclockwise loosens. A 300 to 75 ohm adapter is not included with your Zenith Entertainment Machine. back of remote 120 V AC 60 Hz 1 2 3 4

206-3375 P A G E 8 Connect Cable Service to your Entertainment Machine Hook up your Entertainment Machine, see diagrams at right. Remove the back of the remote and put in two AAA batteries. Plug in your TV. Do not plug it into a switched outlet. Go to page 13 to EZ Program your Entertainment Machine. Mini glossary CABLE SERVICE The wire that supplies all your cable TV (CATV) stations. Cable TV wall jack Cable TV wall jack Cable box In Out RF coaxial wire (75ohm) RF coaxial wire (75ohm) 3 4 output switch TV back panel (expanded view) Antenna / Cable Typical TV back TV back panel (expanded view) Antenna / Cable Typical TV back If you’re using a cable box, leave your TV on channel 3 or 4 and use your cable box to change channels. Remember to set the cable box output channel switch to channel 3 or 4. If you’re using a cable box, EZ Program (page 13) might only find the channel your cable service is on (usually channel 3 or 4). Don’t worry, that’s all you need! back of remote 120 V AC 60 Hz 1 2 3 4 Without Cable Box With Cable Box

Machine, see diagrams at right. Remove the back of the remote and put in two AAA batteries. Plug in your TV. Do not plug it into a switched outlet. Go to page 13 to EZ Program your Entertainment Machine. Hook Up Antenna and a VCR 206-3482 Connect an off air antenna and VCR to your Entertainment Machine In Out Audio R-L Out Video Out 3 4 VCR back VCR back A/V panel Flat wire (300 ohm) Antenna 300/75 ohm Adapter output switch A/V cables not included with TV TV back panel (expanded view) Typical TV back RF coaxial wire (75ohm) not included with TV Round wire (75ohm) Antenna Front input jacks are also available for Video, L - R Audio. L audio R video s-video back of remote 120 V AC 60 Hz Remember to set the VCR output channel switch to channel 3 or 4. Video sources provide better picture and sound. Without A/V cable hookup, VCRs will not play videocassettes in stereo sound. 1 2 3 4 P A G E 9

206-3529 P A G E 1 0 Connect Cable service and a VCR to your Entertainment Machine Leave your VCR and your television tuned to channel 3 or 4 and use the cable box to change channels. Remember to set the cable box output channel switch to channel 3 or 4. Video sources provide better picture and sound. No A/V cables are included with your Zenith Entertainment Machine. Without A/V cable hookups, VCRs will not play videocassettes in stereo sound. Cable TV wall jack Cable box In Out 3 4 output switch Cable TV wall jack RF coaxial wire (75ohm) In Out Audio R-L Out Video Out 3 4 VCR back VCR back A/V panel output switch A/V cables not included with TV TV back panel (expanded view) Typical TV back RF coaxial wire (75ohm) not included with TV Front input jacks are also available for Video, L - R Audio. L audio R video s-video back of remote 120 V AC 60 Hz Hook up your Entertainment Machine, see diagrams at right. Remove the back of the remote and put in two AAA batteries. Plug in your TV. Do not plug it into a switched outlet. Go to page 13 to EZ Program your Entertainment Machine. 1 2 3 4

or DVD Player Back A/V panel Audio R-L Out S-Video Out (VCR Only) Attach to cable wall jack, cable box, or antenna A/V cables not included with TV TV back panel (expanded view) Front input jacks are also available for S-Video, L - R Audio. L audio R video s-video Mini glossary SUPER S-VHS VCR Provides higher quality picture and sound than an ordinary VCR when connected to the S-Video jacks. DVD PLAYER Digital Video Disks can be connected to the S-Video jacks to provide the highest quality reproduction available from this technology. Connecting a S-VHS VCR or DVD player to your Entertainment Machine Super VHS VCR / DVD Player Locate the Ant In jack on the back of your S-VHS VCR. Connect the cable line coming from your wall directly to this jack. Now locate the Out to TV jack. Connect a cable from the Out to TV jack to the ANTENNA/CABLE jack on the back of your TV. Find the audio and S-Video jacks on the back of your S-VHS VCR, and connect them following the instructions provid- ed with your equipment. 1 2 3 Super VHS VCR DVD Player Jacks P A G E 1 1 206-3591 Use Video/Audio sources for better picture and sound. To use with PIP: go to the Source Menu (page 24) and choose the jack you’ve connected your S-VHS equipment to as the Main or PIP source. Both Video and S-Video jacks are available. You can con- nect equipment to either of these input jacks but not at the same time. Use the R - L Audio input jacks with either the S-Video or Video input. DVD (Digital Video Disk) Player Simply connect the S-Video/Audio out on the DVD to the S-Video, Audio R-L Mono on the TV.

External Audio Connection A/V cables are not included with TV R-L Audio Input Stereo System Typical TV back Locate the jacks marked VARIABLE AUDIO OUT, R - L. These are for the stereo system. Connect the stereo system’s cables, according to their color (red is the right channel, white the left) to these jacks. 1 Before you begin plugging in your stereo system, it’s a good idea to put it in its approximate place first. That way you know how much wire you have or will need. Use your stereo to play the sound from your Entertainment Machine

CABLE TV Your EZ Program selection, if you subscribe to a cable service. EZ Program (Channel Search) 1 2 3 4 5 6 Use EZ Program to automatically find and store in the TV’s memory, all the channels in your area Select: AIR ANTENNA, If you receive over-the-air programs. CABLE TV, If you subscribe to a cable service. CABLE TV AIR ANTENNA NEXT NEXT MENU EZ PROGRAM ADD/DEL/SURF EZ CLOCK CAPTIONS CAPTION/TEXT LANGUAGE SOURCE MENU SETUP MENU MOVE 206-3591 Note: EZ Program finds channels being received by the TV tuner. Cable will not work unless you subscribe to a cable service. P A G E 1 3 Press MENU repeatedly until the SETUP menu appears. Using the Up or Down arrow on the remote control, select EZ Program on your screen. Press the Right arrow to go to the EZ Program options. Using the Up or Down arrow, choose either Air Antenna, or Cable TV on your screen. Press the RIGHT arrow to begin the channel search. When the search is complete, press QUIT repeatedly to return to TV viewing. PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 6 1 2/4 2/4 3/5

Remote Key Functions for TV Mode Note: Pressing TV puts remote into TV operating mode A quick list of the keys on your remote and what they do in TV mode, see page 44 for remote key functions in the other modes PRG (PROGRAM) Programs your remote to operate other products. See page 38. FLASHBK (FLASHBACK) Return to the last channel viewed. POWER Turns TV On or Off. CABLE / VCR / AUX / TV Selects remote operating mode. CHANNEL UP / DOWN Tunes to next available channel. MUTE Turns sound Off and On while the picture remains. ENTER Shows the Channel/Time display. NUMBER KEYPAD Selects channels directly and enters numeric values for some options. MENU Shows on-screen menus for TV mode. See page 18. (MENU) UP / DOWN DIRECTIONAL ARROWS The Up/Down directional arrows select and adjust menu options. remote control part number MBR3458CT (124-233-06) VOLUME LEFT / RIGHT Adjusts the sound level. TV / VCR SOURCE Switches between watching TV through antenna/cable, or one of the video sources. Keys dedicated to VCR functions will still operate your VCR while the remote is in TV mode. CLOSED CAPTIONS Selects Off, On, or EZ Mute. (MENU) LEFT / RIGHT DIRECTIONAL ARROWS The Left/Right directional arrows select and adjust menu options. LED INDICATOR LIGHT Lights when keys are pressed. TIMER Displays the Sleep Timer Menu. See page 30. QUIT/ Removes on-screen menu/display from view. With no menus shown on-screen, turns front surround sound on and off. PIP FEATURES For PIP (Picture-in-Picture) operation. See page 34. SURF Press to turn Surf channel scan on and off for channel scanning using Channel Up/Down. On=Only Surf channels appear. Off=Normal channel scan.

UP/DOWN Use the Menu UP or DOWN directional arrow to “select” or highlight and choose menu options. LEFT/RIGHT Use the Menu LEFT or RIGHT directional arrow to move to or return from the menu options listings. QUIT Exits menus and removes o-screen displays. ENTER Returns to the previously selected menu option on some menus. PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 206-3591 P A G E 1 5 On-Screen Menu Operation 1 2 3 4 5 Use either the remote or the TV front controls to access the on-screen menus UNBLOCKED BLOCKED NEXT NEXT MENU AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF PARENTAL CTRL MENU MOVE On-screen menus automatically disappear after about 20 seconds. Remote must be in the TV mode for it to control the TV. Press TV on the remote to select TV mode. Press MENU repeatedly on the remote control, to “select” one of the five main menus on your screen like PARENTAL CONTROL. Use the UP/DOWN directional arrow to select an option like AUX. BLOCK. (You can select the other menu options like AGE BLOCK by pressing the UP or DOWN directional arrow repeatedly.) Once the option is selected, in this case AUX BLOCK, press the RIGHT directional arrow to go to the next selection of options. Use the UP or DOWN directional arrow to choose an option, in this case BLOCKED or UNBLOCKED. When finished, press MENU repeatedly to go back to the main menu or press QUIT to remove the menus and submenus from the TV screen. 5 1/5 2/4 2/3 2/4

206-3591 P A G E 1 6 How to use your front control panel to operate the menus power volume channel menu L audio R video s-video power volume channel menu L audio R video s-video To access the on-screen menus, press MENU. Pressing MENU repeatedly will cycle through the available menus. Highlight the option you want using the DOWN or UP Channel arrow. ADJUST or change the selected feature using the LEFT or RIGHT Volume arrow. Wait a few moments and the menus will disappear by themselves or press MENU repeatedly to remove menus. Menus disappear by themselves. To get them back, press MENU again. If you’ve lost your remote, you can get a new one by calling 1-800-255-6790 to purchase a replacement. 1 2 3 When using the on-screen menus, the buttons on the TV front panel correspond to the remote control keys as follows: CHANNEL = Moves Up/Down VOLUME = Moves Left/Right 1 3 2 Typical TV Front Panel 4 Turns TV On and Off Front Audio/Video Inputs Front S-Video Input

video s-video Selecting Viewing Sources 206-3591 P A G E 1 7 Pick the viewing source (picture and sound) you want to see and hear on your Entertainment Machine ENTER CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 1 The sources you intend to view should be turned on. You can connect equipment to the Video or S-Video jacks, but not at the same time. Use the Audio input jacks with either the S-Video or Video input. 1 Front and Back Connection Panels. Where picture and sound “sources” are connected. AUDIO/VIDEO OUT VIDEO R -AUDIO-L AUDIO/VIDEO OUT VIDEO R -AUDIO-L AUDIO IN R -AUDIO-L AUDIO/VIDEO OUT VIDEO R -AUDIO-L Camcorder VCR S-Video VCR DVD Player Other Typical Equipment Sources Press TV/VCR SOURCE repeatedly to choose from the available viewing sources that are connected to the TV. Available Sources: Back Connections Panel ANTENNA/CABLE: ANTENNA/CABLE on TV back Jackpack, Over-the-Air Antenna or Cable service signal source. Video 1: Video on TV back Jackpack, Audio/Video Inputs. S-Video 1: S-Video on TV back Jackpack, Audio/Video Inputs. Front Connections Panel Video 2: Video on TV Front Jackpack, Audio/Video Inputs. S-Video 2: S-Video on TV Front Jackpack, Audio/Video Inputs.

206-3591 P A G E 1 8 Descriptions of the menus and displays on your Entertainment Machine Menu Name Page Description/Function ON-SCREEN MENUS SETUP 13 Sets the TV up and adjusts the basic features. Your options are: EZ Program 13 Automatically finds and stores active channels you will choose using Channel Up/Down. Add/Del/Surf 20 Choose which channels will appear when using Channel Up/Down. Adds favorite channels to Surf list. EZ Clock 21 Sets the TV’s clock. Captions 22 Turns closed captioning on, off, or set it to come on when the television sound is muted. Caption/Text 22 Chooses a captioning or text option. Language 23 Chooses the language you want the on-screen menus to appear in. Source Menu 24 Selects which picture and sound will appear on your TV main screen and PIP inset picture. V I D E O 25 Adjusts the picture for different viewing situations. Your options are: Contrast, Brightness, Color, Tint, Sharpness, Color Temperature, EZ Picture. AU D I O 26 Customizes the sound to suit your room and taste. Your options are: Bass, Treble, Balance, Audio Mode, Front Surround, EZ Soundrite, Speakers, EZ Sound. PARENTAL CTRL 27 Allows parents to block any program or A/V source for up to 99 hours, with the use of a password. SPECIAL 30 Goes beyond basics and customizes your Entertainment Machine’s features. Your options are: EZ Timer 30 Sleep Timer Sets a time that the TV will automatically turn itself off. On Time Sets the time the TV will turn on automatically each day. Off Time Sets the time the TV will turn off automatically each day. On/Off Timer Enables or disables the On and Off Time features. Channel Labels 32 Titles the channels with their network names (ABC, CBS, HBO, etc.). XDS Display 32 On/Off. If available, shows program information when a channel is tuned or ENTER is pressed. PIP Menu 33 Adjusts the Contrast, Color, Tint, and Size of the PIP picture. EZ Demo 36 Demonstrates the on-screen menus that control the TV’s setup and operational features. EZ Help 37 Help menu offers several features from different menus that can be adjusted on one convenient menu. ON-SCREEN DISPLAYS Surf’s Up 19 Indicates channel selection is in Surf mode. No Surfing 19 Indicates that Surf channel selection has been turned off and normal channel selection mode is on. Mute 19 Indicates sound has been removed. Volume Display 19 Shows the current sound level. Channel/Time 19 Shows the current time, channel, video/incoming audio signal, and channel label if available. PIP/Channel 19 Appears on the Channel/Time display if PIP is on. Sleep Timer 19 Chooses the amount of time in which the TV will turn itself off. Captions/Text 19 Selected caption or text option appears on-screen if provided by broadcaster.

On-Screen Displays “Surf” Channels Mode Active Display Press SURF to turn on Surf channels tuning mode; only channels specified as Surf channels will appear when using channel Up/Down. No Surfing Press SURF to display “No Surfing!” and return to normal channel tuning mode. Mute Display Press MUTE to quiet sound. Press MUTE again to remove the sound. Press MUTE a third time to restore the sound. Volume Display Press the VOLUME Left/Right arrow on the remote control, to view the sound status. Channel/Time Display (Shown above with PIP on) Press ENTER on the remote control to view the Channel- Time-Incoming Audio signal display. Channel selection mode is indicated by flashing source; Main screen or PIP inset. Pressing QUIT/ repeatedly with the Channel/Time display on-screen will move the note symbol allowing you to choose either main screen or PIP as the sound source. Remove On-Screen Displays and Menus Press QUIT/ to remove displays or menus, returning to TV viewing. Or, wait a few moments and the displays or menus will automatically disappear from the screen. Turns front surround sound on or off, if no menus are shown on-screen. Captions/Text (Appear if available, see example above) Press CC repeatedly to select a Captions/Text option or to turn Captions/Text off. Sleep Timer Display Press TIMER on the remote control to view the Sleep Timer Status Display. Press TIMER repeatedly to set the amount of time before the TV automatically turns itself off. On-screen displays reveal the current status of your Entertainment Machine SOFT MUTE PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP B A B C D E C D E SLEEP TIMER 0:10 G VOLUME CH 32-UPN 2:45 STEREO PIP CH 2-CBS PM Closed Captions scroll across the screen as an aid to viewers and the hearing impaired....viewer Surf’s Up! No Surfing S F A F G

206-3591 P A G E 2 0 PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 2/5 Mini glossary ADDED Includes new channels to the channel list that you'll scroll through when using Channel Up/Down. DELETED Removes channels that you don't watch from the channel list you'll scroll through using Channel Up/Down. SURF Adds your favorite channels to the Surf channel list. Press SURF, channels you specify as Surf channels will be the only ones to appear when you use Channel Up/Down. Press SURF repeatedly to turn Surf off, (No Surfing!) and return TV to normal channel selection mode. 1 2 3 4 5 DELETED ADDED SURF NEXT NEXT MENU EZ PROGRAM ADD/DEL/SURF EZ CLOCK CAPTIONS CAPTION/TEXT LANGUAGE SOURCE MENU SETUP MENU MOVE CH 20 Customize your channel selection list: Add Channels not found by EZ Program Delete channels you don’t watch Create a favorite channels list to “Surf” - - with Surf on, only those channels specified as Surf channels will appear when pressing the Channel Up/Down keys Use the NUMBER keypad to go to the Channel you want to add, delete, or include in the Surf channel list. Press MENU repeatedly until the SETUP menu appears. Use the Up/Down arrow to highlight the Add/Del/Surf option, then press the Right (adjust) arrow. Use the Up/Down arrow to pick ADDED or DELETED or SURF; move the check mark next to the option. Use MENU to go back to the SETUP menu. Press QUIT to remove menu when finished. Or, go to another channel you want to add, delete, or include as a Surf channel by using the NUMBER keypad to select the channel and repeat from Step 3. If you’ve deleted a channel, it isn’t gone for good. Just select it using the NUMBER keypad on the remote, or add it later. Surf channels are automatically added. 1 6 6 3/4 3 3/4

Setting the Clock 1 2 3 TO SET PRESS NEXT NEXT MENU EZ PROGRAM ADD/DEL/SURF EZ CLOCK CAPTIONS CAPTION/TEXT LANGUAGE SOURCE MENU SETUP MENU MOVE AUTO MANUAL CLOCK MODE TIME ZONE DAY. SAVINGS EZ CLOCK BACK MENU MOVE 4 PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 1 4 3 2/3 2/3 3/4 1/3 Mini glossary TIME A four-number figure broken down into hours and minutes; first two numbers are hours, last two numbers are minutes. HOURS First two numbers that are entered when setting the clock. MINUTES The second two numbers that are entered when setting the clock. FLASHBK Use to set AM or PM when setting time. In the Setup menu with the EZ Clock option highlighted, press the Adjust RIGHT arrow to go to the EZ Clock Menu. Use the Select UP or DOWN arrows, the Adjust LEFT or RIGHT arrows, and the NUMBER keypad to set the clock menu options. As indicated on the menu, use FLASHBK to set AM or PM. EZ Clock Menu Options Press ENTER or QUIT to return to TV viewing. Set the clock yourself or have the TV do it for you Manual Mode User sets the EZ Clock options. • Clock Mode: Auto, Manual. • Time Set: Set Hours and minutes using the NUMBER keypad or the left/right arrow keys. Use Flashbk to set AM/PM. Automatic Mode TV sets the clock, but the user can enter the menus and make custom changes if needed. • Time Zone: Auto, Eastern, Central, Mountain, Pacific. • Daylight Savings: Auto, Off, On. AM/PM

Selecting Captions/Text Options 1 2 3 4 Turn on Closed Captioning or Captions when sound is Mute, then choose a Closed Captions or Text option Captions come in handy when the television is on mute. Standard closed captioning is available using the Caption 1 option. Not all programming has closed captioning or text available; even though Captions 1, 2, 3, 4, and Text 1, 2, 3, 4 are available to broadcasters. Press MENU repeatedly until the SETUP menu appears. Use the Up/Down arrow to highlight the Captions option, then press the Right arrow. Use the Up/Down arrow to select Off, On or EZ Mute, then press the Right arrow. Note: If you selected either On or EZ Mute, then use the Up/Down/Left/Right arrows to choose an option from the Caption/Text menu: Caption 1, Caption 2, Caption 3, Caption 4, Text 1, Text 2, Text 3, or Text 4. The option will appear when the TV sound is muted or a program is tuned to that has Closed Captions or Text available. Press QUIT to remove menu and return to TV viewing. The Caption/Text feature sets up your Entertainment Machine to receive various closed caption and text options provided by broadcasters. Availability and functionality of Caption/Text is determined only by the broadcaster and may not be available. Mini glossary CAPTIONS The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster. OFF ON EZ MUTE NEXT NEXT MENU EZ PROGRAM ADD/DEL/SURF EZ CLOCK CAPTIONS CAPTION/TEXT LANGUAGE SOURCE MENU SETUP MENU MOVE CAPTION 1 CAPTION 2 CAPTION 3 CAPTION 4 TEXT 1 TEXT 2 TEXT 3 TEXT 4 NEXT NEXT MENU EZ PROGRAM ADD/DEL/SURF EZ CLOCK CAPTIONS CAPTION/TEXT LANGUAGE SOURCE MENU SETUP MENU MOVE PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 4 1 3 2/3 2/3 2/3

Selecting a Language for the Menus ENGLISH SPANISH FRENCH NEXT NEXT MENU EZ PROGRAM ADD/DEL/SURF EZ CLOCK CAPTIONS CAPTION/TEXT LANGUAGE SOURCE MENU SETUP MENU MOVE 1 2 3 4 Press MENU repeatedly to select the SETUP menu. Use the Up/Down arrow to select the Language option on your screen, then press the Right arrow. Use the Up/Down arrow to choose any of the following options: English, Spanish or French. Press QUIT to remove menu and to return to TV viewing. Choose the language you want the on-screen menus to appear in 1 PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 4 2/3 2/3 2

Selecting Main Picture/PIP Sources NEXT NEXT MENU EZ PROGRAM ADD/DEL/SURF EZ CLOCK CAPTIONS CAPTION/TEXT LANGUAGE SOURCE MENU SETUP MENU MOVE TO SET PRESS ANTENNA/CABLE VIDEO 1 VIDEO 2 MAIN SOURCE PIP SOURCE SOURCE MENU BACK MENU MOVE 1 2 3 4 Selecting Sources with the Menus Press MENU repeatedly to select the SETUP menu. Use the Up/Down arrow to select SOURCE MENU, then press the Right arrow. Use the Up/Down arrow to choose MAIN SOURCE or PIP SOURCE option, press the Right arrow. Use Up/Down arrow to select ANTENNA/CABLE, Video 1, or Video 2. After you have selected viewing sources for the Main pic- ture screen and the smaller PIP inset, press QUIT to remove menus and return to TV viewing. Using TV/VCR SOURCE to Choose Viewing Sources Press TV/VCR SOURCE repeatedly to scroll through the available sources: ANTENNA/CABLE, VIDEO 1, VIDEO 2. With the smaller PIP inset picture on-screen, press PIP Ch repeatedly to toggle between Main Picture channel tuning mode and PIP inset channel tuning mode. (Pressing ENTER reveals what channel tuning mode the TV is in shown by the “blinking” on-screen display.) Choose the picture and sound you want to view on the Main Picture Screen and the smaller PIP inset PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 1 5 2/3 No extra equipment required for PIP source. This TV has two tuners which allows the viewer to see two different channels at the same time; one channel on the Main picture and another channel on the PIP inset. Mini glossary ANTENNA/CABLE The source from the ANTENNA/CABLE jack. VIDEO 1, 2 The equipment connected to the video input jacks on the back or front of the TV: VCR, DVD, camcorder etc. TV/VCR SOURCE The key on the remote control providing direct access to available sources. 2/3 2/3 5 A A

Setting the Video Menu Options 1 2 3 Customize the picture to your personal viewing preferences With the VIDEO menu on-screen, use the Up/Down arrow to select an option like EZ Picture, press the Right arrow to go to the EZ Picture menu selections. Using the Up/Down arrow, select a Video menu feature. Your options are: After you have used the Up/Down and Left/Right arrows to select and adjust the VIDEO menu options to your preference, press QUIT to return to TV viewing. CONTRAST BRIGHTNESS COLOR TINT SHARPNESS COLOR TEMP EZ PICTURE Move Next MENU Adjust VIDEO MENU CONTRAST 64% Mini glossary Custom The settings you have changed to your personal preferences. Preset Select this option to reset the video menu settings to their original levels. PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 1/3 3 1/2/3 1/2/3 3 Contrast: Changes the amount of difference between black lev- els and white levels in your picture. Brightness: Increases or decreases the amount of white in your picture. Color: Adjusts levels of all colors. Tint: Adjusts the relative amounts of the colors red and green in your picture. Sharpness: Raises or lowers the definition of the picture. The lower the level, the softer the image will appear. Color Temperature: Changes the overall picture appearance. Options are: Warm, Medium, Cool. EZ Picture: Sets your viewing preference based on the viewed image’s setting. Options are: Custom, Normal, Movie, Digital Pres, Video Game, Sports, Weak Signal, Night Time.

Setting Audio Menu Options Mini glossary AUDIO MODES Mono Sound is broadcast over one audio track. Stereo Sound is broadcast over two audio tracks, divided between the left and right speakers. 2nd Audio/SAP An extra audio signal that may be transmitted in addition to the regular audio portion of a broadcast. 1 2 3 4 Personalize the sound coming from your Entertainment Machine With the AUDIO menu selected and the Audio Mode option highlighted, press the Right arrow. Using the Left/Right arrows, select your preferred settings. Choose from Mono, Stereo, or SAP. Audio Menu Options Include: Press the Left arrow to go back to the AUDIO menu and change other options settings to your preference. Press QUIT to remove menu and return to TV viewing. Not all programming is broadcast in stereo sound, or has Second Audio Programming/SAP. If 2nd Audio SAP is selected and none is present, audio may not be heard. BASS TREBLE BALANCE AUDIO MODE FRONT SURR EZ SOUNDRITE SPEAKERS EZ SOUND Move Next Menu Adjust AUDIO MENU BASS 92% PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 2 2/3 1/2 4 2 • Bass: Increases/decreases lower-end sounds. • Treble: Increases/decreases higher-end sounds. • Balance: Allows you to put the sound more to the left or right channel. • Audio Mode: Chooses sound: Stereo, Mono, 2nd Audio/SAP. • Front Surr: Turns the front surround sound on or off. (Or QUIT/ will turn front surround sound on and off, if no menus are shown on the screen.) • EZ SoundRite: Scans for changes in sound level during com- mercials, then adjusts the sound to match your current level. • Speakers: Turns the regular speakers on or off. • EZ Sound: Chooses from Custom, Normal, Stadium, News, Music, or Theater. (Normal resets all audio settings to original levels.)

Parental Control Overview Mini glossary MOTION PICTURE ASSOCIATION OF AMERICA (MPAA) RATING SYSTEM G General Audiences Content not offensive to most viewers. PG Parental Guidance Content is such that parents may not want their children to view the program. Suggested PG-13 Parental Guidance Program is inappropriate for preteens, with a greater degree of offensive material Suggested than a PG rated program. R Restricted viewing Not for children under age 17. Strong elements of sex and/or violence. NC-17 Restricted Viewing Not for children under age 17 under any circumstances. Strong sexual content. X Hard Core Films Same as NC-17 rating. Note: Zenith Electronics Corporation is not liable for any program content that appears when using this rating system; as always, user discretion is advised. Overview To insure complete coverage for all TV programs, (movies and regular TV shows) choose a rating for “MPAA”, from the selections below AND choose ratings from the “TV Parental Guideline Rating System” on the next page, using the Age Block option for General Audiences, and for Children. In addition to those, you may wish to include additional restrictions from the Content Block menu. See the Parental Control menu, and submenus example on the next page. Things to Consider before Setting Up Parental Control Determine which rating you consider acceptable to the viewer. (For example, if you choose TV-PG, all more restrictive ratings will be automatically blocked; the viewer will not be able to see: TV-PG, TV-14, or TV-MA rated programming.) Do you want to block the auxiliary video source entirely? (Blocks the signal sent by the equipment, such as a VCR, con- nected to the TV Audio/Video input jacks; in the Aux. Block option.) Or leave unblocked, and have the restrictions you specified filter programming from the video source. Block program “Content” based on individual parameters such as: Strong Dialog, Bad Language, Sex Scenes, Violence Scenes, or Fantasy Violence Scenes; in the Content Blk option. How many hours do you want Parental Control to be active? You can set the Hours option for up to 99 hours. Select a secret password; in the Set Password option. Use the NUMBER keys on the remote. Don’t forget the password, it is the only way you can access the Parental Control menu and change rating selections, or turn Parental Control off. Do you want Parental Control to be active all the time? If not, you can turn it on or off; with the Lock On/Off option. This optional feature can be used to “block” undesirable programming from appearing on your TV Note: If you use this feature, PIP will not be available. You should set Parental Control viewing restrictions for General Audiences and for Children - - both should be active at the same time. Simply specifying one content block such as Sex Scenes, will not automatically block another content in the programs from appearing. If you choose to leave the Aux inputs unblocked, the rat- ings you specify will still restrict the programming content that appears from the video sources. You cannot disable Parental Control by disconnecting the TV from power. Block hours will automatically reset to the orig- inal block time setting specified if power is disconnected. Parental Control offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on the TV. Parental Control allows the user the capability of defining which program rating they consider accept- able, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-number code, the password. The number of hours blocked are specified. For complete coverage, General Audience and Children viewer blocks should both be programmed into the TV’s memory. Viewer ratings are specified for both TV and the motion picture industry; both rating systems can be used. The ratings are based mainly on the ages of children.

Using Parental Control Mini glossary TV PARENTAL GUIDELINE RATING SYSTEM TV-G General Audience Considered suitable for all audiences; children may watch unattended. TV-PG Parental Guidance Suggested Unsuitable for younger children, may contain: Suggestive Dialog, Bad Language, Sex, and Violence Scenes. TV-14 Parents Strongly Cautioned Unsuitable for children under 14, may contain: Strong Dialog, Bad Language, Sex, and Violence Scenes. TV-MA Mature Audience Only Adults only, may contain: Strong Dialog, Bad Language, Sex, and Violence Scenes. CHILDREN’S CLASSIFICATIONS TV-Y Children Considered suitable for all children under 7 years old. TV-Y7 Children 7 and over Considered suitable for children over 7, may contain Fantasy Violence Scenes. In the PARENTAL CONTROL menu, highlight the Content Block option, then press the RIGHT arrow. Use the Up/Down arrow to select an option, like F. Violence (Fantasy Violence) for example, then press the Right arrow to go to the restrictions menu for Fantasy Violence. Use the Up/Down arrow to select an acceptable rating like TV-Y7. (See the Mini Glossary, Ratings Charts on this and the previous page for rating meanings.) Press the Left arrow to go back to select another Content Block classification like Language for example and then choose an acceptable rating. Or, press the Left arrow repeat- edly to return to the PARENTAL CONTROL menu to select and adjust other options. After you have selected and adjusted the PARENTAL CONTROL menu options to your preferences, select and: - Set the number of hours you want Parental Control on. - Set your 4-number password - - use the NUMBERS on the remote. - Set the Lock On/Off option to either on or off. Press QUIT to remove menus from the screen. 1 After you have read the preceding page, follow instructions below to set up and activate Parental Control UNBLOCKED BLOCKED NEXT NEXT MENU AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF PARENTAL CTRL MENU MOVE Note: Use the remote control to set up Parental Control. ENTER 0 MENU QUIT PIP PIP ch FREEZ CC Right Arrow Left Arrow Up Arrow Down Arrow QUIT Removes all menus from screen Follow These Instructions No Rating, means the broad- cast does not contain any rat- ing information. Select the “No Rating” option and block it if appropriate.

UNBLOCKED BLOCKED NEXT NEXT MENU AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF PARENTAL CTRL MENU MOVE PARENTAL CTRL BACK MENU MOVE NEXT PARENTAL CTRL BACK MENU MOVE NEXT UNBLOCKED G and above PG and above PG-13 and above R NC-17 X AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF GENERAL CHILDREN TO SET PRESS UNBLOCKED TV-G and above TV-PG and above TV-14 and above TV-MA UNBLOCKED TV-Y and above TV-Y7 PARENTAL CTRL BACK MENU MOVE NEXT AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF DIALOG LANGUAGE SEX SCENES VIOLENCE F VIOLENCE NO RATING TO SET PRESS UNBLOCKED TV-PG and above TV-13 and above PARENTAL CTRL BACK MENU MOVE NEXT AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF UNBLOCKED BLOCKED UNBLOCKED TV-Y7 PARENTAL CTRL BACK MENU MOVE NEXT AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF ENTER CODE: - - - - TO SET UNBLOCKED TV-PG and abo TV-14 and abo TV-MA 00 Hours PARENTAL CTRL BACK MENU MOVE NEXT AUX. BLOCK MPAA AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON/OFF ON OFF P A G E 2 9

EZ Timer: Sleep and On/Off Timers PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP A Sleep Timer Direct Access Press TIMER to place the Sleep Timer menu on the screen. Press TIMER repeatedly to scroll through the available sleep timer set- tings and choose one of the preset turn-off times. Options are: Off, 10, 20, 30, 60, 90, 120, 180, or 240 minutes. You can also set the Sleep Timer by using the menu. Using the EZ Timer Menu On Time With the EZ Timer menu selected, use Up/Down arrows to choose On Time, then press the Right arrow. Use the NUMBER keypad or the Left/Right arrows to pick a time for the TV to automatically turn itself on each day. Use FLSHBK to choose AM or PM. Off Time With the EZ Timer menu selected, use Up/Down arrows to choose Off Time, then press the Right arrow. Use the number keypad or the Left/Right arrows to pick a time for the TV to automatically turn itself off each day. Use FLSHBK to choose AM or PM. On/Off Timer With the EZ Timer menu selected, use Up/Down arrows to choose On/Off Timer, then press the Right arrow. Choose either: On-TV will automatically turn itself on and off each day at the specified times. Off-TV will not turn itself on and off each day, but the turn on and turn off times will be retained in memory for future use. Press QUIT to return to TV viewing. TO SET TIMERS NEXT NEXT MENU EZ TIMER CH. LABELS XDS DISPLAY PIP MENU EZ DEMO EZ HELP SPECIAL MENU MOVE AM PM SLEEP TIMER ON TIME OFF TIME ON/OFF TIM. EZ TIMER BACK MENU MOVE FLSHBK 8:00 NEXT A Set the Sleep Timer to automatically turn the TV off, after the preset time has expired On/Off Timer to turn TV on and off each day at the specified time B B C B B B C B

Selecting Channel Labels 1 2 3 4 5 If a channel label is picked, the Channel Label for the channel you are watching appears when you press ENTER or change to a different chan- nel that also has a channel label; a convenient way to know which net- work you are viewing. Some networks display their own channel labels. Channel Labels do not appear for video sources. Pick a preset label to help identify the network you just tuned to or are currently watching Using the NUMBER keypad or the CHANNEL Up/Down arrow, pick the channel you want to label. Press MENU repeatedly to choose the SPECIAL menu. Use the Up/Down arrow to select CH. LABELS, then press the Right arrow. Select a Label for the Channel Press the Down arrow key (each press will bring up a different label) to go through the alphabetical listing, starting with A - B - C - D, etc. Or, use the Up arrow key to go through the alphabetical listing backwards, starting with Z - Y - X - W, etc. - - - - Autolabel setting will show a label if one is provided by the broadcaster. Press QUIT to accept the label and return to regular TV viewing or use the NUMBER keypad to select another label and repeat from Step 3. CH 20 USA NEXT NEXT MENU EZ TIMER CH. LABELS XDS DISPLAY PIP MENU EZ DEMO EZ HELP SPECIAL MENU MOVE Channel/Time Display with Channel Labels Mini glossary ---- This label indicates that a label will appear if one is provided by the broadcaster. None This label prevents any labels from appearing. CH 32-UPN 2:45 STEREO PIP CH 2-CBS PM Closed Captions scroll across the screen as an aid to viewers and the hearing impaired....viewer PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 2 1 5 3 1 1 3/4 3/4

XDS Display 1 2 3 Press MENU repeatedly to select the SPECIAL menu on your screen. Use the Up/Down arrow to select the XDS DISPLAY option, then press the Right arrow. Use the Up/Down arrow to choose: On, or Off. On, XDS Display will appear as channels are changed or ENTER is pressed, Off, XDS Display will not appear. Press QUIT to remove the menu and return to TV viewing. OFF ON NEXT NEXT MENU EZ TIMER CH. LABELS XDS DISPLAY PIP MENU EZ DEMO EZ HELP SPECIAL MENU MOVE 4 PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 1 4 Mini glossary XDS Extended Data Service - - if provided by the broadcaster, may show some or all of the following information: Channel/Time/Audio display, Network label if present, Title of program, Length of program in hours and minutes, and the Time remaining on the program in hours and minutes, Program content rating and if PIP is active, the PIP channel number. Use the Extended Data Service to show in-depth program information At this printing, XDS data is only being provided by some broadcast- ers; and as a result, may only be available on some channels. Even though XDS data may be present, it may not be available during commercial or network breaks. Ch 25 - PBS 7:15 Stereo PIP Ch 30-ABC NOVA Length 01:00 Time Left 00:45 Rating: TV-14 PM 2/3 2 2/3

Setting the PIP Inset Options NEXT NEXT MENU EZ TIMER CH. LABELS XDS DISPLAY PIP MENU EZ DEMO EZ HELP SPECIAL MENU MOVE TO SET PRESS CONTRAST BRIGHTNESS COLOR TINT SIZE PIP MENU BACK MENU MOVE ADJUST 1 2 3 4 Press MENU repeatedly to select the SPECIAL menu on your screen. Use the Up/Down arrow to highlight the PIP MENU option, then press the Right arrow. Use the Up/Down/Left/Right arrows to select and change the PIP menu options. Press QUIT to remove menu and return to TV viewing. Customize the PIP inset appearance and size 3 PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 1 4 Turn to the next page for a more detailed description of the PIP feature. 2/3 2/3 2/3 • Contrast: Changes the amount of difference between black levels and white levels in your picture. • Brightness: Increases or decreases the amount of white in your picture. • Color: Adjusts levels of all colors. • Tint: Adjusts the relative amounts of the colors red and green in your picture. • Size: Selects the PIP inset picture size. Options are: Large, Small.

Two-Tuner PIP Overview NEXT NEXT MENU EZ PROGRAM ADD/DEL/SURF EZ CLOCK CAPTIONS CAPTION/TEXT LANGUAGE SOURCE MENU SETUP MENU MOVE TO SET PRESS ANTENNA/CABLE VIDEO 1 VIDEO 2 MAIN SOURCE PIP SOURCE SOURCE MENU BACK MENU MOVE PIP = Picture-In-Picture Think of PIP as a mini TV screen superimposed onto your main TV screen Press PIP on the remote to place the PIP inset on the screen, press PIP again to remove it PIP Inset Picture Main Picture YOUR PICTURE-IN-PICTURE FEATURE The Picture-In-Picture (PIP) function allows you to put a smaller picture, called the “inset,” on the bigger screen, or the “main” picture. Normally you would need some other piece of equipment, like a VCR, to act as a tuner to receive and display a second channel at the same time. Your TV eliminates that need by giving you two tuners on one TV, on the Antenna/Cable source. PIP is always available, no matter what equipment you have. Don’t want to miss any of the big game, but hate commercials? Just put the game in the PIP inset, and Surf your favorite chan- nels on the main picture screen. WORKING WITH PIP Just like your Entertainment Machine’s main screen, PIP will need a source to take its image from. Set the main screen source to Antenna/Cable, then set the PIP source to Antenna/Cable, as an example. Then if you use the TV’s tuner to pick your channels, you can enjoy 2-tuner PIP; channel scan capability for both the main screen and the PIP inset. PIP can be used in any picture mode. Put Antenna/Cable in the inset while you watch a video tape, from a VCR connected to Video 1. Have a DVD disk playing in the PIP inset, while you watch a videotape on the main screen. SOME TYPICAL PIP/MAIN SCREEN VIEWING SETUPS 1. You want to watch a videotape, but keep scanning for another movie or game. Set the PIP source to Video 1, or 2 and you can watch the VCR and TV, swapping between the two. 2. You want to watch your favorite live program on Antenna/Cable on the main picture and when a commercial break appears, swap to the PIP inset; which has a videotape in the VCR ready to play, or Surf your favorite channels using the Antenna/Cable source for the PIP inset. If no equipment is connected to a source you select for the PIP inset, or if it is turned off, the PIP inset will be black. Mini glossary TUNER A device that picks up broadcast signals and turns them into picture and sound. A/V SOURCE Other equipment connected to the TV Audio/Video source inputs on the TV back or front connections panel; Video 1 or Video 2. Use the Source Menu to choose Main screen and PIP sources.

Using the PIP Feature Using two-tuner, Picture-in-Picture (PIP) features ENTER 0 MENU RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER FLASHBK (FLASHBACK) Returns to the last channel viewed. Up/Down/Left/Right Arrows UP/DOWN ARROWS Swap Main and PIP sources LEFT/RIGHT ARROWS Move PIP inset around screen. CH 32-UPN 2:45 STEREO PIP CH 2-CBS PM PIP Inset Picture Press PIP to turn PIP on and off. Move PIP Around Screen Press Right/Left arrows to move the PIP inset to the other corners of the screen. Main Screen Picture With PIP off, press FREEZ to place the Main screen pic- ture in the PIP inset and “freeze” the image thereby turning PIP on. (A good way to freeze the image so you can write down phone numbers etc.) Swap Main Picture with PIP Press the Up/Down arrows repeatedly to swap the images between the Main picture and PIP inset. Main Picture Source In Main picture channel tuning mode, press TV/VCR SOURCE to change the source to ANTENNA/CABLE, Video 1, or Video 2. (Or, use the Setup Menu.) Musical Note Symbol Indicates if PIP or the Main screen is the sound source. (In this case sound is from Main screen source.) To change sound source, press QUIT repeatedly with the Channel/Time/Audio Display on-screen. Channel/Time/Audio Source Display Press ENTER to show display. Shows source for: Main picture, PIP, and sound source (Main or PIP). Channel Tuning Mode Press PIP ch repeatedly to switch channel tuning between Main screen and PIP inset. Flashing shows channel tuning mode; in this case, channel tuning is for the PIP inset. (When you press Channel Up/Down, the channels in the PIP inset change.) PIP Source In PIP channel tuning mode, press TV/VCR SOURCE to change the source for the PIP inset to ANTENNA/CABLE, Video 1, or Video 2. (Or, use the Setup Menu.) FREEZ PIP On: Freezes image in PIP inset. PIP Off: Freezes Main screen picture in PIP inset and turns PIP on. QUIT Chooses sound source. (With Channel/Time Display on-screen.) ENTER Shows Channel/Time Display on Main screen. TV/VCR SOURCE Chooses Main picture and PIP sources. PIP Turns PIP on and off. PIP CH Chooses the channel tuning mode; Main screen channels or PIP chan- nels. PIP Key Functions PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP

EZ Demo Menu Mini glossary EZ DEMO Feature provides an automatic demonstration of the on-screen menus on your Entertainment Machine. See and learn what features are available to you as EZ Demo cycles through the on-screen menus. 1 2 3 4 Your Entertainment Machine can show you the menus available Even if the TV is turned off, the EZ Demo feature will continue to operate when the TV is turned on again. The only way to turn EZ Demo off is to select Off, in the SPECIAL menu. Press MENU repeatedly to select the SPECIAL menu. Use the Up/Down arrow to select the EZ DEMO option, then press the Right arrow. Use the Up/Down arrow to choose either: On; then press ENTER. EZ Demo will continue to run (even if the TV is turned off and on again) until it is turned off in the SPECIAL menu. Off; EZ Demo will not be active. Press QUIT to remove menu and to return to TV viewing. NEXT NEXT MENU EZ TIMER CH. LABELS XDS DISPLAY PIP MENU EZ DEMO EZ HELP SPECIAL MENU MOVE OFF ON PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 1 4 2/3 2/3 3 2

Using the EZ Help Menu 1 2 3 EZ Help offers solutions to common problems on one convenient menu. Need Help? Go to the on-screen EZ Help menu and use it to solve the problems listed below Press MENU repeatedly to select the SPECIAL menu on your screen. Use the Up/Down arrow to select the EZ HELP option, then press the Right arrow. Use the (Up/Down/Right/Left arrow keys) as described on- screen to select the options below and correct the problem. Press QUIT to remove the menu and return to TV viewing. NEXT NEXT MENU EZ TIMER CH. LABELS XDS DISPLAY PIP MENU EZ DEMO EZ HELP SPECIAL MENU MOVE TO SET PRESS 4 PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 1 4 2/3 2/3 3 • If you do not have any watchable channels: Do a channel search. • If you want to add or delete a channel: Adds or Deletes channels. • If your screen is stained: Use Degaussing. • If you have a color problem: Use viewing option for picture setting. • If there is a volume difference between channels: Turn on Soundrite so sound level is maintained. • If there is noise in picture or picture is shaky: Message shows some common problem solutions. 2/3

Programming the Remote Mini glossary PROGRAMMING Procedure to set up remote to operate other equipment. PRG Programming mode key. DEVICE Infra-red remote controllable electronic accessory equipment. 1 2 3 4 5 6 Set up your remote to operate other IR controlled brand name devices: VCRs, Cable Boxes, TVs, Satellite Receivers, DVD Players, Audio CD Players, Audio Tape Decks, Audio Tuners and Amplifiers etc. See listing on pages 42/43 PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 7 4 6 Programming your Zenith remote may allow you to use one remote to work up to 7 different devices. Not all devices will work with your Zenith remote control. 5 3 Turn on the device you want to program. On the chart on page 42/43, find the type of device you’re programming, and then find the brand name. Make a note of the three-number code, you’ll need it soon. Press and hold PRG. It’s recessed so it doesn’t get pushed accidentally. Use a small, blunt object. When the indicator light turns on, you can release PRG. Push the key name with the type of device you’re program- ming (VCR, CABLE, AUX, TV). Using the NUMBER keypad, enter the three-number code you found on page 42/43. Press ENTER to save the code. (The indicator light will flash 3 times, then turn off to indicate the code is valid.) Point the remote at the device and push POWER. It should turn off. If not, try the other codes listed and continue from step three. Note: To reset remote to factory settings, enter 9-1-1, in Step 5. Note: After programming, be sure to press the mode key first to operate the device you have just programmed. 7 Indicator Light

Amplifier Volume Override Mini glossary AMPLIFIER Audio device which sends sound to speakers, like an Audio Tuner, Receiver, or Amplifier. See Audio Tuners/Amp list on page 43. CABLE BOX VOLUME/MUTE Some cable boxes have volume controls. 1 2 3 4 To put everything back to normal, reprogram the mode from Step 3 with the original brand code. If you can’t find the code for your amplifier, use the Auto Find feature on page 41. Control the volume on your home audio system without changing modes PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 2 4 3 Indicator Light Find the code that operates your amplifier. Test it to make sure it’s the correct one by following the procedure in “Programming Your Remote” on the previous page. Program your audio system into one of the available AUX modes: Aux, Aux+1, Aux+2, or Aux+3. Press and hold PRG on your remote until the indicator light stays lit, then release. Press 4-9-9; then ENTER on the remote. The indicator light will flash three times the code was accepted. Audio system volume/mute now appears in all modes. Note: You can also program Cable Box Volume and Mute control (if available) into your cable box mode (CABLE or AUX mode) by repeating the steps for programming on the previous page but entering 3-9-9, instead of a brand code, then pressing ENTER.

Aux-1, Aux-2, Aux-3 Mini glossary AUX Auxiliary equipment. Can be any equipment which does not have a dedicated key on your remote like Cable or VCR. Typically a second VCR, stereo system, audio tape deck, etc. 1 2 3 4 5 6 Control up to seven different devices with your remote PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP 4 2 5 6 Programming your Zenith remote may allow you to use one remote to work up to 7 different products or devices. Some devices may not work with your Zenith remote control. 3 Refer to the chart on page 42/43 to find the type and brand name of the device you're programming. Press and hold down PRG with a small blunt object until the indicator light turns on, then release PRG. Press AUX and the 1 on the NUMBER keypad at the same time (for AUX +1). Using the NUMBER keypad, enter the three-number code for the device you've selected. Press ENTER to save the code. With the device turned on, point the remote at it and press POWER. It should turn off. Repeat the steps for AUX+2, and AUX+3. 7 Indicator Light

Remote Control Auto Find 206-3483 Mini glossary AUTO FIND Another way of finding a brand code for controlling auxiliary equipment such as a VCR, DVD player, etc. that is not available through the regular remote brand code programming method. 1 2 3 4 5 6 You can quickly get out of Auto Find by pressing PRG. If the indicator light stays on while you press Power instead of turn- ing off, all the codes have been tried and your device can’t be con- trolled. Use Auto Find to automatically search and try all possible brand codes PRG POWER CABLE VCR AUX TV SURF ENTER FLASHBK MUTE CHANNEL CHANNEL VOLUME VOLUME 1 2 3 4 5 6 7 0 8 9 MENU REWIND FFWD RECORD QUIT PIP PIP ch FREEZ CC TV/VCR SOURCE PAUSE TIMER PLAY STOP Turn on the device you want the remote to control. Press and hold PRG until the indicator light turns on, then release PRG. Press the key for the device you are trying to program (CABLE, VCR, AUX, TV). Press 0-0-0 (zero-zero-zero), then press ENTER right away. Aim the remote at the correct device and push the POWER key (The indicator light will turn off while the POWER key is pressed). Allow a second to pass, then push the POWER key again. Repeat until the device turns off. Push ENTER to save the code (The indicator light will flash 3 times and then turn off). Press POWER to turn the device back on. 7 4 4/6 3 2 Indicator Light 5/7

TVs VCRs Cable Boxes Admiral . . . . . . . 261 Akai . . . . . . . . . . 292 717 718 719 720 Audio Dynamics . . 726 Bell & Howell . . . . 247 Broksonic . . . . . . 221 250 255 729 Candle . . . . . . . . 727 Canon . . . . . . . . . 704 Capeheart . . . . . . 728 Citizen . . . . . . . . 727 Craig . . . . . . . . . 212 Curtis Mathes . . . 259 266 725 727 Daewoo . . . . . . . 244 246 248 254 703 729 Daytron . . . . . . . 246 DBX . . . . . . . . . . 726 Electrochrome. . . . 730 Emerson . . . . . . . 203 221 243 250 293 721 722 729 730 731 732 Fisher . . . . . . . . . 211 212 213 247 265 274 General Electric . . 216 220 266 282 701 702 725 Go Video . . . . . . . 256 262 263 700 Goldstar . . . . . . . 253 Harmon Kardon . . . 296 Hitachi . . . . . . . . 257 270 273 292 705 706 707 708 J.C. Penny . . . . . . 268 726 Jensen . . . . . . . . 292 JVC . . . . . . . . . . 224 225 258 268 292 299 726 Kenwood . . . . . . . 268 292 726 727 Magnavox . . . . . . 275 Marantz . . . . . . . 267 268 726 727 Memorex . . . . . . . 212 298 MGA . . . . . . . . . . 297 730 Mitsubishi . . . . . . 276 277 278 279 280 296 297 730 Montgomery Ward 216 219 249 291 730 MultiTech. . . . . . . 727 NEC . . . . . . . . . . 267 268 269 281 292 709 726 Orion . . . . . . . . . 250 Panasonic . . . . . . 245 251 259 713 714 715 716 Pentax . . . . . . . . 708 727 Philco. . . . . . . . . 275 Pioneer . . . . . . . 210 282 726 Portland . . . . . . . 246 727 ProScan . . . . . . . 216 260 266 282 725 Quasar . . . . . . . . 259 295 Radio Shack . . . . . 213 265 730 RCA . . . . . . . . . . 216 220 228 240 242 249 260 266 282 283 284 285 286 287 288 708 710 711 725 Realistic . . . . . . . 212 213 265 730 Saisho. . . . . . . . . 722 Salora . . . . . . . . . 297 Samsung . . . . . . . 220 230 Sansui . . . . . . . . 289 292 709 726 Sanyo . . . . . . . . 212 247 294 Scott . . . . . . . . . 243 290 729 Sears . . . . . . . . . 211 212 213 265 274 Sharp . . . . . . . . . 261 730 Signature 2000 . . . 216 219 249 Sony . . . . . . . . . 232 723 724 Sylvania . . . . . . . 275 297 Tatung . . . . . . . . 268 292 Teac . . . . . . . . . . 268 Teknika . . . . . . . . 272 Toshiba . . . . . . . . 213 274 290 297 Vector Research . . 726 727 Victor . . . . . . . . . 726 Video Concepts . . . 726 727 XR - 1000 . . . . . . 243 Yamaha . . . . . . . . 726 Zenith . . . . . . . . 201 224 225 229 Admiral . . . . . . . . 121 Bell & Howell . . . . 121 Citizen . . . . . . . . 121 Curtis Mathis . . . . 121 Daewoo . . . . . . . 149 Elektra . . . . . . . . 121 Kurazi . . . . . . . . . 121 Lodgent. . . . . . . . 121 Logik . . . . . . . . . 121 Majestic . . . . . . . 121 Memorex . . . . . . . 121 Montgomery Ward . 121 Teknika . . . . . . . . 121 Telerent. . . . . . . . 121 Signature 2000 . . . 121 XR-1000 . . . . . . . 121 Zenith . . . . . . . . 101 121 149 152 TV/VCR Combination Codes Adventura TV/VCR . 154 Daewoo TV/VCR . . 148 Funai TV/VCR. . . . 154 Goldstar TV/VCR. . 153 172 Symphonic TV/VCR 154 Zenith TV/VCR . . . 150 153 154 172 Allegro . . . . . . . . 358 362 Allegro A-B Switch 361 Archer . . . . . . . . 325 Century . . . . . . . . 325 Citizen . . . . . . . . 325 Comtronic . . . . . . 326 Garrard . . . . . . . . 325 Gemini . . . . . . . . 305 331 338 General Electric. . . 367 General Instrument 304 305 306 307 308 309 310 318 Hamlin . . . . . . . . 302 303 345 365 366 Jasco . . . . . . . . . 325 Jerrold . . . . . . . . 304 307 308 309 310 318 360 363 Kale Vision . . . . . 335 Macom . . . . . . . . 321 Magnavox . . . . . . 327 334 NSC . . . . . . . . . . 335 339 368 369 370 Oak . . . . . . . . . . 311 332 342 Panasonic . . . . . . 313 320 Philips . . . . . . . . 325 327 347 350 352 354 355 Pioneer . . . . . . . . 315 343 RCA . . . . . . . . . . 341 Regency . . . . . . . 329 Samsung . . . . . . . 326 335 Scientific Atlanta 316 323 336 337 364 Signal . . . . . . . . . 326 SL Marx. . . . . . . . 326 Sprucer . . . . . . . . 313 Standard Comp . . . 335 Stargate . . . . . . . 326 379 Teleview . . . . . . . 326 Texscan . . . . . . . 339 356 371 Tocom . . . . . . . . 317 318 346 Unika . . . . . . . . . 325 348 362 Universal . . . . . . 325 358 362 Vid Tech . . . . . . . 340 Video Way . . . . . . 349 Viewstar . . . . . . . 327 354 355 372 Zenith HT-2000. . . 353 Zenith PM . . . . . . 374 Find the codes you need to program your remote. On this page: TVs, VCRs,and Cable Boxes

Programming Codes 206-3602 DVD Players Audio CD Players Audio Tape Decks Audio Tuners/Amps Satelite Receivers Alphastar. . . . . . . 516 Chaparral. . . . . . . 501 502 Cheyenne. . . . . . . 502 Dishnet . . . . . . . . 515 Drake . . . . . . . . . 503 General Electric. . . 510 517 General Instrument 504 505 Hitachi . . . . . . . . 519 520 Hughes Network . . 514 JVC . . . . . . . . . . 518 Macom . . . . . . . . 314 Magnavox . . . . . . 521 Phillips . . . . . . . . 521 PrimeStar. . . . . . . 513 ProScan. . . . . . . . 510 517 RCA DSS . . . . . . . 373 RCA . . . . . . . . . . 510 517 Realistic . . . . . . . 506 Sierra I . . . . . . . . 502 Sierra II . . . . . . . 502 Sierra III . . . . . . . 502 Sony. . . . . . . . . . 511 STS1. . . . . . . . . . 507 STS3. . . . . . . . . . 508 Toshiba . . . . . . . . 509 512 Uniden . . . . . . . . 522 United . . . . . . . . 344 Zenith Drake. . . . . 312 330 Zenith Satellite . . 328 351 378 500 JVC . . . . . . . . . . 965 Mitsubushi. . . . . . 964 Pioneer . . . . . . . . 963 Sony. . . . . . . . . . 962 Toshiba . . . . . . . . 961 Zenith. . . . . . . . . 960 ADC . . . . . . . . . . 940 ADO . . . . . . . . . . 939 Aiwa. . . . . . . . . . 938 Akai . . . . . . . . . . 937 Denon . . . . . . . . 935 Dynatech. . . . . . . 953 Emerson . . . . . . . 952 Fisher . . . . . . . . . 438 933 951 GE . . . . . . . . . . . 932 Goldstar . . . . . . . 460 Hitachi . . . . . . . . 950 JVC . . . . . . . . . . 949 954 Kenwood . . . . . . 441 931 948 Luxman . . . . . . . . 930 Magnavox . . . . . . 421 422 433 434 Marantz. . . . . . . . 929 947 MCS . . . . . . . . . . 928 Mitsubishi . . . . . . 927 Nakamichi . . . . . . 925 926 Onkyo . . . . . . . . 923 924 946 Optimus . . . . . . . 920 921 922 Panasonic . . . . . . 431 432 945 Phillips . . . . . . . . 421 433 434 Pioneer . . . . . . . . 431 435 944 Quasar . . . . . . . . 432 Radio Shack . . . . . 431 441 RCA . . . . . . . . . . 437 943 Sanyo . . . . . . . . . 438 439 Sears . . . . . . . . . 936 Sharp . . . . . . . . . 441 442 Sherwood . . . . . . 449 Sony. . . . . . . . . . 420 443 444 445 934 Soundesign . . . . . 461 498 901 902 Sylvania . . . . . . . 433 Teac . . . . . . . . . 418 419 Technics . . . . . . . 432 Toshiba . . . . . . . . 915 Yahama . . . . . . . . 414 941 942 Zenith . . . . . . . . 460 461 498 901 902 Sony. . . . . . . . . . 452 Citizen . . . . . . . . 914 GE . . . . . . . . . . . 916 Goldstar . . . . . . . 460 474 Hitachi . . . . . . . . 919 JVC . . . . . . . . . . 908 Kenwood . . . . . . . 484 Luxman . . . . . . . . 467 Marantz. . . . . . . . 903 913 Memorex . . . . . . . 485 Nad . . . . . . . . . . 904 Nakamichi . . . . . . 493 Onkyo . . . . . . . . 471 906 Optimus . . . . . . . 905 Panasonic . . . . . . 912 Pioneer . . . . . . . . 470 485 907 Proton . . . . . . . . 910 Quasar . . . . . . . . 912 RCA . . . . . . . . . . 909 Sharp . . . . . . . . . 483 917 918 Sherwood . . . . . . 900 Sony. . . . . . . . . . 486 489 490 491 492 Soundesign . . . . . 461 498 901 902 Toshiba . . . . . . . . 915 Techniques. . . . . . 912 Victor . . . . . . . . . 908 Zenith . . . . . . . . 460 461 498 901 902 Find the codes you need to program your remote. On this page: Cable, Satellite, CD Players, Tape Decks and Audio Tuners and Amplifiers.

206-3591 P A G E 4 4 A complete list of key functions for your remote control Some of the functions shown above may not be available on your equipment. TV Mode VCR Mode Cable Mode AUX Mode KEY NAME Zenith Code 101 Zenith Code 201 Zenith Code 353 Zenith Code 960 PRG Program Mode Codes Program Mode Codes Program Mode Codes Program Mode Codes POWER TV On/Off VCR On/Off Cable Box On/Off AUX On/Off CABLE Selects Cable Selects Cable Selects Cable Selects Cable VCR Selects VCR Selects VCR Selects VCR Selects VCR AUX Selects AUX Selects AUX Selects AUX Selects AUX TV Selects TV Selects TV Selects TV Selects TV Surf Channel Preview VCR SP/EP Cable FC/Fav Ch AUX Audio FLASHBK TV Flashback VCR Flashback Cable Flashback AUX Return MUTE TV Mute TV Mute TV Mute TV Mute CHANNEL UP TV Channel Up VCR Channel Up Cable Channel Up AUX Skip >> CHANNEL DOWN TV Channel Down VCR Channel Down Cable Channel Down AUX Skip << VOLUME (RIGHT) TV Volume Up TV Volume Up TV Volume Up TV Volume Up VOLUME (LEFT) TV Volume Down TV Volume Down TV Volume Down TV Volume Down 1 TV Digit 1 VCR Digit 1 Cable Digit 1 AUX Digit 1 2 TV Digit 2 VCR Digit 2 Cable Digit 2 AUX Digit 2 3 TV Digit 3 VCR Digit 3 Cable Digit 3 AUX Digit 3 4 TV Digit 4 VCR Digit 4 Cable Digit 4 AUX Digit 4 5 TV Digit 5 VCR Digit 5 Cable Digit 5 AUX Digit 5 6 TV Digit 6 VCR Digit 6 Cable Digit 6 AUX Digit 6 7 TV Digit 7 VCR Digit 7 Cable Digit 7 AUX Digit 7 8 TV Digit 8 VCR Digit 8 Cable Digit 8 AUX Digit 8 9 TV Digit 9 VCR Digit 9 Cable Digit 9 AUX Digit 9 0 TV Digit 0 VCR Digit 0 Cable Digit 0 AUX Digit 0 ENTER TV Enter VCR Enter Cable Enter AUX Display MENU TV Menu VCR Menu Cable Menu AUX Menu UP ARROW TV Select Up VCR Select Up Cable Up Arrow AUX Up Arrow DOWN ARROW TV Select Down VCR Select Down Cable Down Arrow AUX Down Arrow LEFT ARROW TV Adjust Left VCR Adjust Left Cable Left Arrow AUX Title RIGHT ARROW TV Adjust Right VCR Adjust Right Cable Right Arrow AUX Sub-Title QUIT/(Note) TV Surr Sound VCR Quit Cable Quit AUX Resume PIP TV PIP VCR+ Day Up AUX Marker PIP CH TV PIP Channel Mode VCR Eject Tape Day Down AUX Marker Search FREEZ TV PIP Freeze VCR Commercial Skip Cable Page Up AUX Repeat-Chap CC TV Closed Captions VCR Memory Cable Page Down AUX Repeat A-B TIMER TV Timer VCR Timer Cable Timer AUX Program TV/VCR/SOURCE TV Sources TV Tuner or VCR Tuner Cable Info AUX Open/Close RECORD VCR Record VCR Record Cable Buy AUX Angle PAUSE VCR Pause VCR Pause Cable Guide AUX Pause REWIND VCR Rewind VCR Rewind VCR Rewind AUX Scan << PLAY VCR Play VCR Play VCR Play AUX Play STOP VCR Stop VCR Stop VCR Stop AUX Stop/Eject FFWD VCR Fast Forward VCR Fast Forward VCR Fast Forward AUX Scan >> References: MBR3458CT, 124-233-06 and µP 221-1445-01

Maintenance Caring for your Entertainment Machine 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Entertainment Machine. 1. Use a soft cloth with a mild soap solution to wipe the cabinet. 2. Rinse the cloth and wipe the cabinet again. 3. Let the cabinet air-dry before turning your Entertainment Machine on. Use a quality wood cleaner and polish. This will protect the Entertainment Machine from dirt and dust, as well as keep the cabinet looking new. If you leave your Entertainment Machine dormant for a long time (such as a vacation), it’s a good idea to unplug the power to protect against possible damage from lightning or power surges. If you use an off-air antenna, you may also want to disconnect it from the back of your TV before leaving. Screen Cleaning Extended Absence If you unplug your Zenith Entertainment Machine, you may have to reset the clock using the EZ Clock menu described earlier. See page 21. Cabinet Cleaning Wood Cabinet Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have with your new Entertainment Machine. Be sure to turn the power off and pull out the plug before you begin any cleaning.

Some quick and easy tips to fixing problems yourself SYMPTOMS Snowy picture and poor sound. Multiple images or ‘ghost shadows.’ Interference: Sharp lines across the screen and poor sound. Normal picture but no sound. No picture and poor sound. No picture and no sound. No color, but the sound is O.K. Picture has a big black box on it, but the sound is O.K. Picture has two horizontal black bars, one on top and one on bottom. Remote control doesn’t work. Menu options can’t be changed or selected. No picture or sound when a non-cable source is selected. SOLUTIONS • Check your antenna connection or location. • Check your antenna direction and/or location. • Make sure the wire from your antenna to your Entertainment Machine is properly connected. The following may cause image problems or distortion: Electrical appliances, powerful lights, cars, trucks; computers or portable phones; medical equipment • If possible increase the distance between your Entertainment Machine and the offending appliance. Or shut one of them off. • Check volume levels. • Make sure the TV is not muted. • Try another channel. The problem may be the broadcast, not your Entertainment Machine. • Are the Audio A/V cables properly installed? • Are you in TV or cable tuning mode, and should be in the other? • Make sure output channels on all A/V equipment are on the same channel (3 or 4). • Check that all connections are tight. • Is the AC power cord plugged in? • Check that your AC power outlet works. (Test it by plugging in something else or try another plug.) • Make sure your brightness and audio controls are set properly. • Try another channel. The problem may be with the broadcast. • Check the color control in the VIDEO menu. • Try another channel. The problem may be with the broadcast. • Is Text model selected but no text is available on the broadcast? • The CC (closed caption) option may be in Text mode. Select OFF in the Captions menu (see page 22). • Your program is in letterbox. This means that the shape of your TV is a square, but the program is a rectangle. Think of the bars as empty space the program doesn’t fill; not picture that’s blocked out. Because this format is a direct representation of film as you see it in movies, you are actually seeing MORE of the program when you see those bars. • Make sure the batteries are fresh and installed properly. Does indicator light work, is it nice and bright? • Is remote in TV mode? Press TV for TV mode. • Try unplugging your Entertainment Machine for a few minutes, then plug it back in. (Don’t forget to reset the clock.) • Check to see if the source equipment has been turned on. • Make sure that the connections are secure on the back of your TV and on the source.

when using a stereo VCR. With no key presses, on-screen menus continue to appear. PIP Problems PIP does not work. The PIP inset is black or lacks contrast when VIDEO is the PIP source. The PIP inset is “snow” when the source is Video. There is no picture in the PIP inset when using VIDEO for the PIP and Antenna/Cable for the main picture. 206-3591 P A G E 4 7 Trouble Shooting continued Parental Control Problems Can’t tune to programs listed in TV guide. Parental Control doesn’t work. Can’t watch TV or VCR. Programs with a rating of PG-13, R, NC-17, and X do not appear. Can’t view TV-PG program. TV turns itself off, or on by itself. SOLUTIONS • Check to see if all the connections are secure. • Look in the AUDIO menu to see if all the settings are correct. • EZ Demo feature is operating. Turn EZ Demo off in the SPECIAL menu. • Is Parental Control set to block programming? • Check that all the wires are connected properly. • PIP source turned on? • Look to see if the TV/VCR button on your VCR has the TV selected. • Look to see if the TV/VCR button on your VCR has the TV selected. • Is Block option not allowing programs to appear? • Parental Control set to block rating? • Has Block Time expired? Lock On/Off turned Off? No hours set? • Is Parental Control block on? Are Aux inputs blocked? Do you know the password to unblock Parental Control? • Is Parental Control set to block programs with those ratings. • Is TV-PG set to be blocked in Parental Control? Reset restrictions to PG-13, then TV-PG rated programs will appear. • Sleep Timer set to turn TV off. • Is the On/Off Timer set to turn TV on and off at preset times? • Power Failure? Continued on next page

206-3591 P A G E 4 8 SYMPTOMS Channel/Time Display does not disappear after a period of time. EZ Help menu shows only two options. SOLUTIONS • Display will not function properly if a selected source does not have any equipment connected to it. • A Video source is the selected source. Main screen source has more EZ Help options. Some quick and easy tips to fixing problems yourself

Glossary A/V CABLES Audio and Video cables. Three cables bunched together—Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo playback of video- cassettes and for higher quality picture and sound from other A/V devices. A/V DEVICE Equipment that produces picture and sound (VCR, DVD, cable box, or television). ADDED Includes channels that you want to watch in addition to the channels found by EZ Program. AMPLIFIER An external device that amplifies sound from a television, CD player, VCR, DVD, etc. ANTENNA The physical receiver of television signals sent over the air. (A large metal piece of equipment does not always have to be visi- ble for your home to be using an antenna.) CABLE Cable Box operating mode on the remote. CABLE SERVICE Programming provided by a cable company. CAPTIONS/TEXT A form of subtitling that writes out the dia- log for your program. DELETED Removes channels that you don’t watch from the channels found by EZ Program. ICON A small picture on your screen representing a function or menu item. INPUT Refers to the jack that receives a signal into the TV, VCR or other A/V device. JACK A connection on the back of a TV, VCR, or other A/V device. This includes the RF jack that is threaded with a place for a small wire in the center, and the Audio/Video jacks that have a bigger opening and are color-coded. MODE The equipment that the remote control is currently controlling (TV, VCR, Cable, etc.) is the remote’s operating “mode.” MONO SOUND Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio. OHM RF CABLE The wire that comes from an off air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the large threaded jack on the back of your TV. OUTPUT Refers to the jack that sends a signal out of a VCR, DVD, or other A/V device. PIP This is the most common way to refer to the Picture-in-Picture (PIP) feature. SECOND AUDIO Second Audio Programming (SAP) PROGRAMMING/SAP is another, separate, audio channel available with some programming. Choosing 2nd Audio/SAP often refers to listening to audio in another language, such as Spanish or French. SIGNAL Picture and sound traveling through cable, or over the air, to your television screen. SOURCE The term for the equipment or connection that provides audio and video (picture and sound) to your Entertainment Machine. VCR, DVD players, or Cable Boxes are examples of sources. STEREO SOUND Stereo (stereophonic) sound refers to audio that’s divided into right and left sides or channels. SURF Use the Surf feature to create a special list of your favorite channels. You can access the “Surf” channels by pushing SURF on the remote to put the TV into Surf channel tun- ing mode. Press Surf again to cancel Surf channel tuning mode. TUNER Device that picks up broadcast signals and turns them into picture and sound. A list of definitions for some of the words found in this operating guide

Set up your game room or spare room in style!! Sturdy black wall mounts keep the TV off your furniture and in easy view. All mounts have 90 degree and 10 degree tilt angles. • ALGW27 fits most 25” to 27” TVs - ONLY $59.99 • ALGW20 fits most 19” and 20” TVs - ONLY $49.99 • ALGw13 fits most 13” Televisions - ONLY $39.99 Available in White, just add “-WH” to part number (e.g. ALGW27-WH) FOR ALL ORDERS ADD $6.95 SHIPPING & HANDLING TELEVISION WALL MOUNTS Use Your Visa or MasterCard to Order PLEASE ALLOW 3 - 4 WEEKS FOR DELIVERY zenith Receive Local programming NOT available on your Satellite sys- tem!!! Perfect backup antenna for cable outages. Enhanced quality picture and stereo sound in weak signal areas. • Amplified VHF/UHF/FM Antenna includes 4 feet of 75 ohm cable for easy hookup. ONLY $34.95 PLUS $6.95 SHIPPING & HANDLING INDOOR AMPLIFIED ANTENNA ATS 775 Broken or lost remote? Need a second remote or more functions? Order direct from Zenith!! • Operates TV, VCR, CD, DVD, & Cable Box • Operates PIP and Most Screen Menus • Extended Range & MORE!!! Orders 1 year or more after product purchase may receive upgraded models. Other Remotes with 3, 4, 5 & 7 Functions Available Upon Request ZENITH 5 FUNCTION REMOTE ONLY $19.99 PLUS $6.95 SHIPPING & HANDLING ZEN 525 ORDER TODAY! CALL OR FAX TOLL-FREE 1.800.255.6790 Fax 1.888.693.6484 email: [email protected] B-AD REV4/7/99

Welcome to the Zenith family! We believe that you will be pleased with your new Zenith Entertainment MachineTM. Please read this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state within the U.S.A. ZENITH’S RESPONSIBILITY Service Labor During a period of 90 days from effective warranty date, Zenith will provide service labor by a Zenith authorized service center when needed, as determined by the Zenith service center, as a result of manufacturing defects. Parts New or remanufactured replacements for factory-defective parts will be supplied by a Zenith authorized service center for one year from effective warranty date (color picture tube — two years). Such replacement parts are warranted for the remaining portion of the original warranty period. Home Service Warranty service for 21” diagonal (U.S.A.) or larger screen size models is provided in the home in most cases. (Some repairs may require the unit to be taken by the servicer to the repair facility and returned, at no additional charge.) Not Covered This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls in the home, installation or repair of home antenna systems, cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or other causes beyond the control of Zenith. Any alteration of the product voids this warranty in its entirety. THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MER- CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ZENITH SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDEN- TAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. SOME STATES DO NOT ALLOW LIMI- TATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. OWNER’S RESPONSIBILITY Effective Warranty Date Warranty begins on the date of original consumer purchase. For your convenience, keep the dealer’s dated bill of sale or delivery ticket as evidence of the purchase date. Operating Guide Read your Operating Guide carefully so that you will understand the operation of your set and how to adjust the customer controls. Carry-In Service Models under 21” diagonal (U.S.A.) screen size must be taken to a Zenith authorized service center for warranty service and must be picked up by the owner. Antenna Reception problems caused by inadequate home antenna or faulty antenna connections are the owner’s responsibility. Important Product Registration—Please fill out and mail your Product Registration Card. It is imperative that Zenith know how to reach you promptly if we should discover a safety problem that could affect you. Warranty Service For warranty service information, contact any Zenith authorized service center. Parts and service labor that are Zenith’s responsibility (see above) will be provided without charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory warranty service, call or write the Zenith Response Center. You must provide the model number, serial number and date of purchase or date of original installation. Before you ask for warranty service, read “Maintenance And Troubleshooting” in your operating guide. You might avoid a service call. Be sure to send in the Product Registration Card. We will send you an application for the Protection Plan near the expiration of the two-year manufacturer’s warranty on the picture tube. For additional information call (256) 774-4088. 206-3591 Issue* Your Zenith Direct-View TV Warranty Additional Zenith Picture Tube Protection Plan Available Zenith offers you the opportunity to obtain additional long-term protection against failure of the picture tube in your new television. Our Picture Tube Protection Plan enables you to avoid any unexpected picture tube repair expenses and keep your television in top condition. It guarantees you a genuine Zenith replacement picture tube and service from a Zenith authorized service center. C-WARR-DV 1/00 ZENITH ELECTRONICS CORPORATION Zenith Response Center 201 James Record Rd., Building 3 Huntsville, AL 35824 Telephone (256) 772-1515 Mon-Fri, 7:00 a.m.- 8:00 p.m. CST Sat, 8:00 a.m.-5:00 p.m. CST www.zenith.com 801 E. Roosevelt Rd. Lombard, IL 60148 Telephone (630) 705-2830 Home & Carry-in Service Television/VCR Parts and Accessories PTV/Camcorders 201 James Record Rd. Building 4 Huntsville, AL 35824 Telephone (256) 774-4025 Service Hours: M-F 8-6, Sat 9-2 Will accept UPS shipments ZENITH CONSUMER SERVICES © Copyright 2000 Zenith Electronics Corporation