Sealey PC220 Instructions

Models:PC220, PC230 & PC250 1. SAFETY INSTRUCTIONS 1.1. ELECTRICAL SAFETY p WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following: You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety. 1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year. 1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician. 1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester. 1.1.4. Ensure that cables are always protected against short circuit and overload. 1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose. 1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the correct fuse - see fuse rating at right. 1.1.7. DO NOT pull or carry the appliance by the power cable. 1.1.8. DO NOT pull the plug from the socket by the cable. 1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK 3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely. Fit a new plug according to the following instructions (UK only). a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’. b) Connect the BROWN live wire to the live terminal ‘L’. c) Connect the BLUE neutral wire to the neutral terminal ‘N’. d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is tight. Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only. To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal. 1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician. 1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm2, but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of 2.5mm2 section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use. 1.2 GENERAL SAFETY 3 Disconnect the cleaner from the power supply before servicing, changing accessories, or performing any maintenance. 3 Use only genuine parts and accessories. Unauthorised parts and accessories may be dangerous and will invalidate your warranty. 3 Maintain the cleaner in good condition. Use an authorised agent for servicing. Keep machine clean, but DO NOT use solvents. 3 Ensure the correct paper filter bag is firmly in place before operating the cleaner. Incorrect bags may cause machine faults and will invalidate your warranty. 3 Wear protective clothing and gloves. 7 DO NOT allow children or untrained persons to operate the cleaner. 7 DO NOT place attachments close to your face (especially eyes, ears, etc). Do not point the hose end at other persons or animals. s DANGER! DO NOT vacuum very fine powders,hot or glowing ash, inflammable, explosive, corrosive or other dangerous substances. 7 DO NOT operate the unit without the paper filter bag (except when wet vacuuming). 7 DO NOT leave machine running unattended. Turn power supply OFF, and DO NOT leave the vicinity until motor has come to a complete stop. 7 DO NOT operate the cleaner when you are tired, under the influence of alcohol, drugs or intoxicating medication. 7 DO NOT use the cleaner in the rain or in very damp conditions. 7 DO NOT use the cleaner for a task it is not designed to perform. 3 When not in use, store the cleaner in a safe, dry, childproof location. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. PC220,PC230 & PC250 - 1 - 050104 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. FUSE RATING 13 AMP Blue Neutral Wire Yellow & Green Earth Wire Cable Restraint Brown Live Wire 2. CONTENTS 2.1. Carton content 2.1.1. Release the side clips and lift the motor head from the bin. Take out the items in the bin. Replace and re-clip motor head. 2.1.2. Check and identify each accessory. If anything is missing or damaged contact your supplier immediately. PC220 & PC230 1. Floor Nozzle 7. Elbow 2. Triangular Nozzle 8. Extension Tube (2) 3. Crevice Tool 9. Flexible Hose 4. Brush Adaptor 10. Base 5. Liquids Adaptor 11. Bin & Motor Head 6. Curtain Nozzle 12. Filter Cartridge (fitted) PC250 1. Brush Frame 7. Extension Tube (2) 2. Liquid Brush 8. Hose Elbow Joint 3. Carpet Brush 9. Hose 2m x 45mm 4. Floor Brush 10. Handle 5. Triangular Nozzle 11. Base 6. Crevice Tool 12. Bin and Motor Head

Bin . . . . . . . .20ltr Air Flow . . . . . .210m3/h Weight . . . . . .7kg PC230 Motor . . . .230V 1100W Bin . . . . . . . .30ltr Air Flow . . . . . .210m3/h Weight . . . . . .7kg PC250 Motor . . . .230V 1200W Bin . . . . . . . .50ltr Air Flow . . . . . .175m3/h Weight . . . . .12kg 3. Assembly 3.1.1. PC220/230 - Push fit bin to base, aligning inlet on bin with triangular mark on top edge of base. PC250 - Pull outwards catch at rear of base, place bin on base (seam to the rear) and release catch. 3.1.2. PC250 only - Slide handle through the four brackets on the bin and tighten clamping screws. The cleaner is now ready for dry vacuum cleaning. Note that PC250 has a two speed switch (1 & 2) as well as an On/Off switch (0 & 1) on top of the motor head. Note: The filter cartridge is reusable. Remove (fig. 1), clean with a soft bristle brush and, if necessary, wash with a fine spray, from the inside out (fig. 2). When wet the filter cartridge is very easily damaged. Do not replace washed filter until it is dry. Replace the filter after approximately 100 working hours. IMPORTANT! If using the optional paper dust bags, which fit over the suction inlet in the bin, do not remove the cartridge filter. The Dust bags should be changed when approximately two thirds full. Always keep a pack of spare bags handy. Paper Dust Bags - pack of 10 (Optional) . . . . . .Part No. 186/83015BOI (PC220/PC230), 186/83015B5I (PC250) Foam Filter (Optional, for wet vacuuming) . . . . . . .Part No. 186/83035BHB (all models) Cartridge Filter . . . . . . . . . . . . . . . . . . . . . . . . . . .Part No. VAC/92/DL (PC220/PC230), VAC92/250/DL (PC250) 4.1. Ensure the machine is unplugged from the power supply. 4.2. Make sure the bin is clean and free from dust and dirt. 4.3. Remove the paper filter cartridge. Fitting foam filter is recommended. 4.4. To the same flexible hose as used in dry cleaning fit the crevice tool. 4.5. Ensure the switch is in the “Off” position and then plug the cleaner into the power supply. 4.6. To vacuum large quantities of liquid, from a sink, or tank, etc., do not immerse tool completely in the liquid, leave a gap at the top of the tool opening to allow an air inflow. See fig. 3. 4.7. The machine is fitted with a float valve which stops the suction action when the bin has reached its maximum capacity or if the cleaner is overturned. There will be an increase in motor speed. When this happens, turn off cleaner, disconnect from power supply, remove head from bin and empty liquid into a suitable receptacle or drain. To continue vacuuming, refit head and proceed. 4.8. After wet vacuuming, turn off the cleaner and disconnect from the power supply. NOTE: The bin is not designed to store liquid, empty the bin after use, clean and dry the inside and outside before storage. Remember! After wet vacuuming the paper filter cartridge must be refitted before dry vacuuming again. pp WARNING! Ensure you read, understand and apply Section 1 Safety Instructions. DO NOT vacuum solvents, explosives, inflammable and/or hazardous liquids such as petrol, oil, spirits, paint, thinners, acids etc. fig. 2 fig. 3 fig. 1 5. TROUBLESHOOTING Cleaner will not operate. Dust comes from the motor cover. Reduced efficiency and increased motor speed/vibration. No power supply. Faulty power cable, switch or motor. Container full of liquid. Filter cartridge missing or damaged. Paper filter bag and/or cartridge clogged. Nozzle, hose or bin inlet blocked. Check supply. Check and repair or replace faulty item. Empty container. Fit or replace. Replace paper filter bag and/or clean cartridge. Check nozzle, hose and bin inlet for blockage. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. 4. WET VACUUM CLEANING Declaration of Conformity We, the sole UK importer, declare that the product listed below is in conformity with the following standards and directives. The construction files for these products are held by the Manufacturer and may be inspected, on request by a national authority to Jack Sealey Ltd. For Jack Sealey Ltd. Sole UK importer of Sealey Qaulity Machinery. Signed by Mark Sweetman 5th January 2004 Wet & Dry Vacuum Cleaner Models: PC220,PC230 & PC250 73/23/EEC Low Voltage Directive 89/336/EEC EMC Directive 93/68/EEC Marking Directive PC220,PC230 & PC250 - 1 - 050104 01284 757500 01284 703534 www.sealey.co.uk Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk. [email protected] email Web 3. SPECIFICATIONS & ASSEMBLY

Description 1 186/30085BOX Castor Wheel 2 186/01002BOA Base 5 186/50079BOA Hose Inlet 6 186/01016BOU Bin Clip 7 186/10039BKM Bin, Stainless Steel, 20 litre (PC220) 7 186/10038BGM Bin, Stainless Steel, 30 litre (PC230) 8 VAC/92/DL Cartridge Filter 9 186/50063BOU Motor Cover, Lower c/w Float Cage 10 186/50077BOV Float 11 186/70032BON Motor Gasket, Lower 12 186/20007BOX Motor 13 186/70033BON Motor Gasket, Middle 14 186/70030BON Motor Gasket, Upper 16 186/50036ZON Cable Sleeve 17 186/70018BON Cover, Switch 18 186/50186B6U Motor Cover, Upper 19 186/80037BOX Switch 20 186/50200BOA Motor Cover, Middle 21 186/83102B6N Filter Grille 22 186/80030ZOI Cable Block 23 186/80021BOX Noise Filter 24 186/80097BOV Cable Connection 25 186/50078ZOX Cable Grip 26 186/50081BOA Curtain Brush 27 186/01317BON Hose Complete, 1.5m x 45mm 28 186/50080BON Crevice Tool 29 186/50091BON Extension Tube 30 186/50089BOA Triangular Nozzle 31 186/50085BON Brush Adaptor 32 186/60277BON Floor Nozzle 33 186/60278BON Liquids Adaptor 34 186/50093BOA Elbow Spare Dust Collection Bags 186/83140BOK Packet of 5 Bin/Lid Gasket 186/70017B5N Foam Filter 186/83035BHB Issue No: 1 Date: 050104 PARTS LIST FOR: WET & DRY VACUUM CLEANERS Models: PC220 & PC230 PC220,PC230 & PC250 - 1 - 050104 01284 757500 01284 703534 www.sealey.co.uk Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk. [email protected] email Web

Description 1 186/50174B8C Knob, Switch On/Off 2 186/50175B8C Knob, Switch 2-speed 3 186/50172BON Switch Shank 4 186/51188BOU Motor Cover, Upper 6 186/50036ZOU Cable Sleeve 7 186/50182B8N Cable Clip 8 186/50181BOC Motor Cover, Middle 9 186/83021B8X Filter, Air Vent 10 186/50170B8A Outlet Air Grill 11 186/83023B8X Silencer, Motor Cover, Middle 12 186/83022B8X Silencer, Motor Cover, Middle 13 186/80702B8X Switch, 2-speed 14 186/50078ZOX Cable Grip 15 186/80701B8X Switch, On/Off 16 186/80099B8V Switch Connections 17 186/80030ZOI Cable Block 18 186/80025B8X Condenser 19 186/30070B5X Anti-static Kit 20 186/50104B9V Diaphragm 21 186/70055BON Gasket, Motor, Middle 22 186/70060B8N Gasket, Motor, Upper 24 186/20025BOX Motor 1200W 25 186/70061BAN Gasket, Motor, Lower 26 186/50077BOV Float 27 186/50064B8U Motor Cover, Lower 28 186/70045B5N Rubber Bearing 29 186/50102B5N Float Cage 30 VAC92/250/DL Filter Cartridge 31 186/40024B5X Handle 32 186/50114BOU Bracket, Handle Fixing 33 186/01016BOU Bin Clip 35 186/50116B5U Handle, Bin Side 36 186/50079BOU Hose Inlet 37 186/10041B5M Bin, Stainless Steel, 50 litres 38 186/30064B5X Spring 40 186/01003B5U Trolley Complete 44 186/60277B0N Frame For Combined Brush 45 186/60278B0N Brush For Liquids 46 186/60280B0N Brush for Carpet 47 186-60279B0N Brush For Floors 48 186/01316BON Hose, Complete, 2.0m x 45mm 50 186/50080BON Crevice Tool 51 186/50093BOA Elbow Joint, Hose 53 186/50089BOA Triangular Nozzle 54 186/50091BON Extension Tube 55 186 -01003B5U Trolley, Complete (includes item Nos 38, 39, 40, 41, 42 & 43) Dust Collection Bags Packet of 10 186/83015B51 Dust Collection Bags Packet of 6 186/83142BOK Foam Filter 186/83035BHB Bin Lid Gasket 186/70017B5N PC220,PC230 & PC250 - 1 - 051202 PARTS LIST FOR: WET & DRY VACUUM CLEANER Model: PC250 Issue No: 1 Date: 050104 01284 757500 01284 703534 www.sealey.co.uk Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk. [email protected] email Web