WBOX Technologies WBXHD041S Operation & User’s Manual

User Manual WBXHD041S WBXHD041S1T WBXHD082S WBXHD082S2T WBXHD162S WBXHD162S4T If you have any questions, please contact your ADI salesperson.

User Manual Precautions Issue V1.0 (2018-06-04) i Precautions Precautions Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip "You have entered the area of electronic surveillance" in an eye- catching place. Failure to correctly use electrical products may cause fire and severe injuries. To prevent accidents, carefully read the following context: Symbols This document may contain the following symbols whose meanings are described accordingly. Symbol Description It alerts you to fatal dangers which, if not avoided, may cause deaths or severe injuries. It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries. It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results. It provides a tip that may help you resolve problems or save time. It provides additional information. To prevent electric shocks or other dangers, keep power plugs dry and clean.  Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users' non- conformance to these requirements.

User Manual ii Issue V1.0 (2018-06-04)  Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.  Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.  If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.  When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.  Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened.  If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.  Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.  Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.  Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.  Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.  Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.  Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.  If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring.  Remove the power plug if the device is idle for a long time.  Before unpacking, check whether the fragile sticker is damaged. If the fragile sticker is damaged, contact customer services or sales personnel. The manufacturer shall not be held responsible for any artificial damage of the fragile sticker.

User Manual Precautions Issue V1.0 (2018-06-04) iii Special Announcement All complete products sold by the manufacturer are delivered along with nameplates, operation instructions, and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products. This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product. The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice. This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.

User Manual iv Issue V1.0 (2018-06-04) Contents Precautions .................................................................................................................... i 1 Specifications............................................................................................................ 1 2 Hard Disk .................................................................................................................. 3 2.1 Precautions ..................................................................................................................... 3 2.2 Hard Disk Recommendation .......................................................................................... 3 2.3 Approximate Video Storage Duration ............................................................................. 3 2.4 Hard Disk Installation .................................................................................................... 4 3 Operation Instruction.............................................................................................. 8 3.1 Front panel ..................................................................................................................... 8 3.2 Rear panel....................................................................................................................... 8 3.3 Startup .......................................................................................................................... 10 3.4 Powering off the Device ................................................................................................ 11 3.5 Logging In to the System .............................................................................................. 11 3.6 Changing the Password ................................................................................................ 12 3.7 Adding Cameras ........................................................................................................... 13 4 Quick Navigation ................................................................................................... 15 4.1 PTZ Operations ............................................................................................................ 17 4.1.1 PTZ .................................................................................................................. 17 4.1.2 UTC ................................................................................................................. 19 4.2 Playback ....................................................................................................................... 20 4.3 Search ........................................................................................................................... 21 4.4 Picture Grid .................................................................................................................. 22 4.5 Event ............................................................................................................................ 23 4.6 Main Menu ................................................................................................................... 23 5 Camera Management ............................................................................................ 25 5.1 Camera Management .................................................................................................... 26 5.1.1 Lock a Camera ................................................................................................. 26 5.1.2 Unlock a Camera .............................................................................................. 26 5.2 Picture Parameter ......................................................................................................... 27 5.3 Encode Parameter ......................................................................................................... 28

User Manual Contents Issue V1.0 (2018-06-04) v 5.4 Video loss ..................................................................................................................... 29 5.5 Motion Detection.......................................................................................................... 33 5.6 Privacy Area ................................................................................................................. 35 5.7 Camera tamper ............................................................................................................. 35 5.8 OSD settings................................................................................................................. 36 6 System setting......................................................................................................... 38 6.1 Basic ............................................................................................................................. 38 6.1.1 System .............................................................................................................. 39 6.1.2 Time ................................................................................................................. 39 6.1.3 Time zone ......................................................................................................... 40 6.1.4 DST .................................................................................................................. 41 6.2 Network ........................................................................................................................ 42 6.2.1 Ipv4 .................................................................................................................. 42 6.2.2 Port ................................................................................................................... 44 6.2.3 UPNP ............................................................................................................... 45 6.2.4 SMTP ............................................................................................................... 46 6.2.5 DDNS ............................................................................................................... 47 6.2.6 Blacklist ........................................................................................................... 48 6.3 Record .......................................................................................................................... 50 6.4 Output........................................................................................................................... 51 6.5 Alarm Manager ............................................................................................................. 54 6.5.1 Surveillance ...................................................................................................... 54 6.5.2 Alarm in ........................................................................................................... 55 6.6 Disk .............................................................................................................................. 56 6.6.1 Viewing Disk Information ................................................................................ 57 6.6.2 Clearing Disk Data ........................................................................................... 57 6.7 Privilege manager ......................................................................................................... 58 6.7.1 User manager ................................................................................................... 58 6.7.2 Modify Password ............................................................................................. 60 6.8 Privacy ......................................................................................................................... 60 6.9 Advanced setting .......................................................................................................... 61 6.10 App ............................................................................................................................. 62 7 Log Center ............................................................................................................... 64 8 Alarm ........................................................................................................................ 66 8.1 Event ............................................................................................................................ 66 8.2 Timeline ....................................................................................................................... 67 8.3 Clear alarm ................................................................................................................... 68

User Manual vi Issue V1.0 (2018-06-04) 9 Web Access .............................................................................................................. 69 9.1 Login ............................................................................................................................ 69 9.2 Live Video .................................................................................................................... 70 9.3 Video Playback ............................................................................................................. 70 9.4 Alarm Search ................................................................................................................ 72 9.5 DVR Setting ................................................................................................................. 74 9.5.1 Viewing basic information ............................................................................... 75 9.5.2 Network management ...................................................................................... 76 9.5.2.1 IPv4 ............................................................................................. 76 9.5.2.2 Port .............................................................................................. 77 9.5.2.3 DDNS .......................................................................................... 78 9.5.2.4 SMTP .......................................................................................... 79 9.5.3 Device management ......................................................................................... 80 9.6 Alarm ............................................................................................................................ 82 9.7 Storage.......................................................................................................................... 84 9.8 User .............................................................................................................................. 85 9.8.1 Privilege management ...................................................................................... 85 9.8.2 Modify password .............................................................................................. 88 9.8.3 Local ................................................................................................................ 88 10 FAQ ........................................................................................................................ 90

User Manual 1 Specifications Issue V1.0 (2018-06-04) 1 1 Specifications Model WBXHD041S WBXHD041S1T WBXHD082S WBXHD082S2T WBXHD162S WBXHD162S4T VIDEO Video Compression H.264 High Profile Encode Ability 4ch*1080P@15fps 8ch*1080P@15fps 16ch*1080P@15fps Decode Ability 4ch *1080P@15fps 8ch*1080P@15fps 16ch*1080P@15fps Video Input Pure Analog: 4ch*1080P/4ch*720 P Pure Analog: 8ch*1080P/8ch*720 P Pure Analog: 16ch*1080P/8ch*72 0P Mixed Input: 4ch*1080P(AHD+T VI+CVI) Mixed Input:8ch*1080P(A HD+TVI+CVI) Mixed Input:16ch*1080P( AHD+TVI+CVI 4ch*1080P(AHD +CVI+ Network 8ch*1080P(AHD +CVI+ Network 16ch*1080P(AHD +CVI+ Network) 4ch*1080P(TVI +CVI+ Network) 8ch*1080P(TVI +CVI+ Network) 16ch*1080P(TVI+C VI + Network Pure Network: 4ch*1080P/4ch*720 P Pure Network: 8ch*1080P/8ch*720 P Pure Network:16*1080P/ 16ch*720P AUDIO Audio Compression G711A Two Way Audio Support RECORD AND PLAYBACK Hard Drive 1 SATA(Each maximum support 6T ) 2 SATA(Each maximum support 6T ) 2 SATA(Each maximum support 6T ) Record Manual/Event/Timer Playback 4ch(pure local input mode) 8ch(pure local input mode) 16ch(pure local input mode) STORAGE AND BACKUP Space Occupation 960H:12G~20G/ day*channel

User Manual 2 Issue V1.0 (2018-06-04) Model WBXHD041S WBXHD041S1T WBXHD082S WBXHD082S2T WBXHD162S WBXHD162S4T 720P:10G~20G/ day*channel 1080P: 20G~30G/ day*channel Audio:691.2M/ day*channel Backup Mode USB HDD INTERFACE Video Input 4ch BNC （AHD/TVI/CVI/C VBS） 8ch BNC （AHD/TVI/CVI/C VBS） 16ch BNC （AHD/TVI/CVI/C VBS） Video Output 1ch VGA,1ch HDMI,1ch CVBS Audio Input 4ch RCA 8ch RCA 6ch RCA Audio Output 1ch RCA Alarm Input N/A 4ch Alarm Output N/A 1ch Network Interface 1 RJ45 10M/100M Adaptive Ethernet Port PTZ Control RS485, Support Multiple PTZ Protocols USB 2 USB Hard Disk 1 SATA 2 SATA GENERAL Power DC12V/2A DC12V/4A Operating Temperature -10°C ~ 50°C (14°F ~ 122°F ) Dimension 255mm(L)*255mm( W)*45mm(H) 350mm(L)* 295mm(W)*45mm(H) Product Weight (Excluding hard disk) 900g 1900g

User Manual 2 Hard Disk Issue V1.0 (2018-06-04) 3 2 Hard Disk 2.1 Precautions  Formatting will clear all video data on the hard disk. Use this function only when necessary.  Be sure to uninstall the hard disk before removing it from the DVR during runtime; otherwise, the hard disk may be damaged or data may be lost.  The DVR must be connected to a stable power supply during runtime; otherwise, the hard disk may be damaged or data may be lost.  The maximum capacity of a single hard disk cannot exceed 6 TB. 2.2 Hard Disk Recommendation Seagate or Western Digital hard disks which are highly stable and inexpensive are recommended. 2.3 Approximate Video Storage Duration Table 2-1 Approximate Video storage duration Maximum Hard Disk Capacity Maximum Bit Rate Approximate Video Storage Duration 1 × 6 TB 18 Mbps 28 days 2×6 TB 36 Mbps 28 days 4 × 6 TB 72 Mbps 28 days Formulae for calculating the approximate video storage duration: Step 1 Use the following formula to calculate the storage capacity q (unit: MBybte) required to record a single video per hour: q = d/8×3600/1024

Digital Video Recorder(DVR) User Manual 4 Issue V1.0 (2018-06-04) d indicates the bit rate (unit: Kbit/s). Step 2 Use the following formula to calculate the approximate video storage duration t (unit: day) w indicates the capacity (unit: Mbyte) of a single hard disk. n indicates the number of disks. h indicates the recording duration per day. c indicates the number of video inputs of the DVR. Table 2-2 shows examples of approximate video storage duration (h is 24 hours). Table 2-2 Examples of approximate video storage duration Hard Disk Capacity Bit Rate Video Count Approximate Video Storage Duration 1×6TB D1, 1.5Mbps 4 85 days 1×6TB 720p, 3Mbps 4 47 days 1×6TB 1080p, 4.5Mbps 4 28 days 2×6TB D1, 1.5Mbps 8 85 days 2×6TB 720p, 3Mbps 8 47 days 2×6TB 1080p, 4.5Mbps 8 28 days 4×6TB D1, 1.5Mbps 16 85 days 4×6TB 720p, 3Mbps 16 47 days 4×6TB 1080p, 4.5Mbps 16 28 days The data listed in the preceding table is only for your reference. The recording time estimate may be different from the actual recording time. The user shall be liable for any loss incurred as a result thereof. 2.4 Hard Disk Installation Take the following steps to install a hard disk: Step 1 Unscrew the four fixing screws on both sides and one fixing screw on the back, then remove the upper cover, as shown in Figure 2-1.

User Manual 2 Hard Disk Issue V1.0 (2018-06-04) 5 Figure 2-1 Removing the upper cover Step 2 Take out the hard disk fixing screws and silicone cushion included in the accessory package, route the fixing screw through the silicone cushion, and install it to the screw holes, as shown in Figure 2-2. Figure 2-2 Installing the hard disk fixing screw Step 3 Route the hard disk fixing screws through the holes on the base, push the hard disk to the appropriate position according to the direction of arrow, as shown in Figure 2-3.

Digital Video Recorder(DVR) User Manual 6 Issue V1.0 (2018-06-04) Figure 2-3 Inserting the hard disk Step 4 Turn the device over, and fasten two hard disk fixing screws, as shown in Figure 2-4. Figure 2-4 Fixing the hard disk Step 5 Install the other hard disk according to Step 2, Step 3, and Step 4, then insert the hard disk data cable and power cable, as shown in Figure 2-5.

User Manual 2 Hard Disk Issue V1.0 (2018-06-04) 7 Figure 2-5 Inserting the cable Step 6 Put on the upper cover, and fasten the fixing screws, as shown in Figure 2-6. Figure 2-6 Put on the upper cover ----End

Digital Video Recorder(DVR) User Manual 8 Issue V1.0 (2018-06-04) 3 Operation Instruction 3.1 Front panel Figure 3-1 shows the front panel of DVR. Table 3-1 shows the description of front panel. Figure 3-1 Front panel Table 3-1 Elements of the front panel NO. Element Description 1 POWER Power indicator, When DVR is operating, the Power indicator is steady on. When DVR is shut down, the PWR indicator is turned off. 2 ALARM Alarm indicator This indicator flashes when alarm is transmitted 3 REC Record indicator This indicator flashes when DVR is recording 4 NET Net indicator This indicator flashes when DVR record 5 USB Supports connection to a USB mouse, a USB flash drive or USB removable hard disk. 3.2 Rear panel Figure 3-2 shows the rear panel of 0E-HD4C1TB and the interfaces on it.

User Manual 3 Operation Instruction Issue V1.0 (2018-06-04) 9 Figure 3-2 Rear panel of 0E-HD4C1TB Figure 3-3 shows the rear panel of 0E-HD8C2TB and the interfaces on it. Figure 3-3 Rear panel of 0E-HD8C2TB Figure 3-3 shows the rear panel of 0E-HD16C2TB and the interfaces on it. Figure 3-4 Rear panel of 0E-HD16C2TB Table 3-2 shows the description of rear panel Table 3-2 Elements of the real panel NO. Name Description 1 AUDIO IN Audio Input 2 ALARM I/O Alarm Input/Output 3 VIDEO IN Video input 4 CVBS CVBS output interface 5 A-OUT Audio output 6 HD-OUT Video output interface 7 VGA 8 AUDIO IN Audio Input

Digital Video Recorder(DVR) User Manual 10 Issue V1.0 (2018-06-04) NO. Name Description 9 LAN network interface RJ45 10 /100/1000 Mbps adaptive Ethernet interface 10 USB Supports connection to a USB mouse, a USB flash drive or USB removable hard disk. 11 RS485 RS485 port 12 DC power interface Connected to an external power adapter 13 Power switch -(Optional for different DVR) 14 Ground screw Safe ground screw of the device 3.3 Startup Before starting the DVR, ensure that the DVR is connected to a power supply. When the DVR is connected to a power supply, it starts automatically upon the initial power-on.  Ensure that a power supply is connected to the DVR correctly.  Before starting the DVR, ensure that a monitor is connected to the HD-OUT or VGA interface of the DVR correctly.  The DVR may not operate normally when a power supply exception occurs, likely causing damage to the DVR in serious conditions. In such a circumstance, you are advised to use a regulated power supply. After the DVR is connected to a power supply, the power indicator is steadily on. Start the DVR. The real-time video screen is displayed, as shown in Figure 3-5.

User Manual 3 Operation Instruction Issue V1.0 (2018-06-04) 11 Figure 3-5 Real-time video screen Users need to provide a hard disk for the DVR. The hard disk is strictly detected during device startup. If the detection result failed, the possible causes are as follows:  The hard disk is new and is not formatted. Log in to the system and format the hard disk.  The hard disk is formatted, but the file system is inconsistent with the file system supported by the DVR. Format the hard disk.  The hard disk is damaged. 3.4 Powering off the Device Click the main menu and choose System setting > Advanced setting, the advanced setting page is displayed, click shutdown to power off the DVR. If there is a power switch on the rear panel of the DVR, you can turn off the power switch to disconnect the DVR from the power supply. 3.5 Logging In to the System Logging In to the Device Step 1 On the DVR login page, select the language, as shown in Figure 3-6.

Digital Video Recorder(DVR) User Manual 12 Issue V1.0 (2018-06-04) Figure 3-6 Login page Step 2 Enter the username and password.  The username and password are both admin.  If you forget password, click Forgot password. You can choose a way to find previous password: 1. Scan the QR code and send the QR code to your seller. 2. Click Send Password to you E-mail. A password retrieval email will be sent to your email address (for details, see 6.2.4 Step 6). Then, you can retrieve password by following operations described in the email. Step 3 Click Login to access the main User Interface (UI). ----End 3.6 Changing the Password Description The change default password page will be displayed as shown in Figure 3-7, when you login the system for the first time.

User Manual 3 Operation Instruction Issue V1.0 (2018-06-04) 13 Figure 3-7 Change the default password page Operation Steps Step 1 Enter the new password, and confirmation password. Step 2 Click OK. The real-time video screen is displayed 3.7 Adding Cameras This DVR can be connected to both analog cameras and network cameras. The DVR gives preference to the access of the analog camera by default. The DVR can be directly connected to analog cameras through bayonet nut connector (BNC) cables. Figure 3-8 shows the topology of the DVR.

Digital Video Recorder(DVR) User Manual 14 Issue V1.0 (2018-06-04) Figure 3-8 DVR topology ----End Switch Remote monitor

User Manual Issue V1.0 (2018-06-04) 15 4 Quick Navigation After the DVR operation screen is displayed, move the cursor to the downmost position of the DVR screen. The DVR floating menu bar is displayed. Click in the left of DVR floating menu bar. a quick main menu is displayed. The quick main menu provides Playback, Search, Picture Grid, Event, System Setting, Exit System and Shutdown, as shown in Figure 4-1. Figure 4-1 Quick main menu In the middle of DVR floating menu bar, the video tool bar provides video window switching, Dwell on, pan-tilt-zoom (PTZ) control, audio, and video signal, as shown in Figure 4-2. Figure 4-2 Real-time video toolbar The real-time video toolbar is described as follows:

User Manual Quick Navigation 16 Issue V1.0 (2018-06-04) : layout button. After this button is clicked, the real-time video window is switched between the single-screen mode and multi-screen mode. Click on the right of screen splitting format and choose the channels to view the video. : Dwell on, After this button is clicked, the layout dwell on screen is enable, for how to set the dwell on, please see 6.4 Step 2. : PTZ button. After this button is clicked, the PTZ operation screen is displayed, where you can adjust the PTZ to control cameras. : Audio button. After this button is clicked, the audio setting screen is displayed, where you can choose the channel and adjust the volume. : Video signal button. After this button is clicked, the video signal setting screen is displayed, as show in Figure 4-3. Figure 4-3 Video signal setting Normally, DVR video signal setting is auto by default, the DVR obtains the video signal of analog camera automatically. When the video is displayed incorrectly, choose the same video signal according to the video signal of analog camera and click OK to save the signal setting. A main menu quick toolbar is display on the right of DVR floating menu bar. The main menu quick toolbar provides Playback, Search, Picture grid, Event, System setting, as shown in Figure 4-4. Figure 4-4 Main menu quick toolbar

User Manual Issue V1.0 (2018-06-04) 17 4.1 PTZ Operations Click the PTZ button on the real-time video toolbar. The PTZ control page is displayed, as shown in Figure 4-5. Figure 4-5 PTZ control 4.1.1 PTZ The PTZ control and function settings are applicable only to high-speed dome, PTZ cameras and cameras externally connected to PTZs, The function in the PTZ control screen is described as follows: : layout button. After this button is clicked, the real-time video window is switched. : PTZ setting button. After this button is clicked, the PTZ setting page is displayed, as shown in Figure 4-6. Figure 4-6 PTZ setting

User Manual Quick Navigation 18 Issue V1.0 (2018-06-04) Operation Steps Step 2 Select a P.T.Z control type from the drop-down list box. RS485: Use RS485 protocol to control analog high-speed domes and analog cameras with Motorized zoom lenses. Coaxial: Use coaxial protocol to control analog high-speed domes and analog cameras with Motorized zoom lenses. All: Math the RS485 or coaxial protocol automatically to control analog high-speed domes and analog cameras with Motorized zoom lenses. Step 3 Select a type of protocol from the drop-down list box. Step 4 Set an address. Step 5 Select a baud rate from the drop-down list box. Step 6 Click OK to save P.T.Z setting or click cancel to cancel the P.T.Z setting. Preset You can configure preset positions and quickly rotate the camera to a preset position by invoking the preset position. Click or of Advanced setting, the preset setting page is displayed, as the red frame shown in Figure 4-7. Figure 4-7 . PTZ setting Operation Steps Step 1 Set preset. 1. Click or to set the preset ID. 2. Click direction button to rotate the camera to a position and click Save to save the preset. Step 2 Invoke preset.

User Manual Issue V1.0 (2018-06-04) 19 1. Select the preset ID. 2. Click Goto to invoke preset, the camera rotate the preset position. Or click Home to rotate the camera to the first preset position. : Channel button. Click or to select the P.T.Z control channel. : Click or to enter the preset setting page. : direction button. Click this button to rotate the position of camera.. : Click or to set the camera speed. : Click or to zoom the lens in or out. : Click or to adjust the focal length. : Click or to adjust the aperture. 4.1.2 UTC The UTC control and function settings are applicable to front-end HD camera and OSD operation of front-end HD camera. Click UTC in PTZ control page, the UTC screen is displayed, as shown in Figure 4-8. Figure 4-8 UTC screen For HD camera of Motorized lens, click or of zoom, focus and iris to adjust the view angle and focal length. For details of OSD operation, see Camera OSD Operation Guide.

User Manual Quick Navigation 20 Issue V1.0 (2018-06-04) 4.2 Playback Playback refers to playing back a video. Click Playback in the quick navigation bar to access the playback screen, as shown in Figure 4-9. Figure 4-9 Playback screen The toolbar at the bottom of the playback screen is described as follows: : Slow play : Fast forward : Pause : Backup. After this button is clicked, the video backup starts. This function is available after a USB flash drive is connected to the DVR. : Download. After this button is clicked, the backup ends. This function is available after the backup function is enabled. : Magnify. Apply only to a single screen. After this button is clicked, the image magnified to 150%, click this button again to restore the original size.

User Manual Issue V1.0 (2018-06-04) 21 : Full screen off. After this button is clicked, the device returns to the real-time video screen. : Indicates whether to insert a USB flash drive. indicates that a USB flash drive is inserted into the DVR. indicates that no USB flash drive is inserted into the DVR. 4.3 Search Search refers to searching for a video by date and time. Operation Description Click Search in the quick navigation bar to access the search screen, as shown in Figure 4-10. Figure 4-10 Search screen The toolbar at the bottom of the play window is described as follows: : Slow play : Fast forward : Pause

User Manual Quick Navigation 22 Issue V1.0 (2018-06-04) : Backup. After this button is clicked, the video backup starts. This function is available after a USB flash drive is connected to the DVR. : Download. After this button is clicked, the backup ends. This function is available after the backup function is enabled. : Intelligent motion detection. After this button is clicked, the device automatically locates a moving target. : Full screen. After this button is clicked, the device plays a video in full screen. Operation Steps Step 1 Click a camera in the camera list on the left side of the search screen. The video view of the selected camera is displayed in the play window. Step 2 Select a date in the calendar on the right side of the search screen. Click or on the left side of the time axis below the play window to switch the time axis, and then select time. Then, the play window plays the video in the specified time range. : Videos are searched on an hourly basis. : Videos are searched on 24 hourly basis. ----End 4.4 Picture Grid Picture grid refers to evenly dividing the video of a channel by time range and searching for a video based on thumbnails divided by time range. Click Picture Grid on the quick navigation bar to access the picture grid screen, as shown in Figure 4-11.

User Manual Issue V1.0 (2018-06-04) 23 Figure 4-11 Picture grid screen Operation Steps Step 1 Select a camera in the camera list on the left side of the picture grid screen. Videos shot by the camera in the earliest time range on the current day are displayed as thumbnails in the window on the right side. Step 2 Select a day of a week on the right of . Step 3 Select a time range on the right of . For example, if you select 7, it indicates that the selected time range is 07:00:00-08:00:00.Videos in this time range are displayed as 12 thumbnails at an interval of 5 minutes in the window on the right. Step 4 Select a required thumbnail, double-click it or right-click it and choose Play from the shortcut menu to play the video. ----End 4.5 Event Click Event on the quick navigation bar to access the alarm event screen. For details about the screen and operations on this screen, see 8.1 "Event". 4.6 Main Menu Right-click on the main UI. The main menu as shown in Figure 4-12 is displayed. The main menu includes Camera, Setting, Log Center, and Alarm.

User Manual Quick Navigation 24 Issue V1.0 (2018-06-04) Figure 4-12 DVR main menu ----End

User Manual Issue V1.0 (2018-06-04) 25 5 Camera Management Camera management mainly involves analog cameras and network cameras. Analog cameras can be directly connected to input channels of the DVR. When analog cameras are insufficient, the DVR automatically searches for and adds network cameras in the same Local Area Network (LAN). Camera management includes camera add or delete, picture parameter, encode parameter, video loss, motion detection, privacy area, camera tamper, and setup OSD. Operation Description Click Camera in the main menu to access the camera management screen, as shown in Figure 5-1. Figure 5-1 Camera management screen

User Manual Camera Management 26 Issue V1.0 (2018-06-04) 5.1 Camera Management 5.1.1 Lock a Camera On the camera management screen, check the locking status of network cameras in the camera list on the right side. If the locking status of a network camera is , you can lock the camera manually. Operation Steps Step 1 Select a network camera to be locked in the camera list on the right side. The real-time video and basic information of the network camera are displayed on the left side. Step 2 Click the button next to Lock below the play window. The button turns blue and the locking status is changed to in the camera list on the right side, click OK, indicating that the camera is locked successfully.  Analog addresses directly connected to the DVR are locked preferentially and are assigned the IP address 127.0.0.1. When channels of the DVR are insufficient for the access of analog cameras, they automatically occupy the channels of network cameras.  If all channels of the DVR are bound to cameras, you need to unbind cameras that do not need to be bound.  You can choose Click Add to automatically add cameras of all idle channels.  If a network camera is added, enter the username and password of the camera below the play window. The video of the camera can be viewed only after successful login. 5.1.2 Unlock a Camera Operation Steps Step 1 Select a camera to be unlocked in the camera list on the right side. Information about the camera is displayed below the play window. Step 2 Click the button next to Lock below the play window. The button turns white and the locking status is changed to in the camera list on the right side, indicating that the camera is unlocked successfully. If you click Clear, a message as shown in Figure 5-2 is displayed. Click OK to unbind network cameras of all channels of the DVR.

User Manual Issue V1.0 (2018-06-04) 27 Figure 5-2 Unlock confirmation message 5.2 Picture Parameter Picture parameters refer to basic attributes of a picture, including the lightness, saturation, contrast, and sharpness. You can set picture parameters for each channel based on scenarios. Operation Description Click Picture Param next to Camera in the main menu or click Menu in the upper left corner of the camera management screen and choose Picture Param to access the Picture Parameter screen, as shown in Figure 5-3. Figure 5-3 Picture Parameter screen The picture parameters are described as follows:

User Manual Camera Management 28 Issue V1.0 (2018-06-04) Brightness: picture brightness. Saturation: brilliance of the picture color. Sharpness: picture clarity. Contrast: picture transparency. Operation Steps Step 1 Click a camera in the camera list on the left side of the Picture Parameter screen. Step 2 Select where to install this camera from the drop-down list. The default values of picture parameters vary with scenarios. Step 3 Set the camera brightness, contrast, saturation, and sharpness. Step 4 Click OK to save picture parameter settings or click Copy to all, then click OK to apply the parameter settings to cameras of all channels. ----End 5.3 Encode Parameter The system allows you to set the main video resolution, sub video resolution, and image quality (low-quality, medium-quality, high-quality, or best-quality) for cameras in a channel, and view the frame rate and stream size in Encode Parameter. Operation Description Click Menu in the upper left corner of the camera management screen and choose Encode Param to access the Encode Parameter screen, as shown in Figure 5-4.

User Manual Issue V1.0 (2018-06-04) 29 Figure 5-4 Encode Parameter screen Operation Steps Step 1 Click a camera in the camera list on the left side of the Encode Parameter screen. Step 2 Select Main Video or Sub Video. Step 3 Set Resolution, Quality, Frame rate, Bitrate and Bitrate type. Step 4 Click OK to save encode parameter settings or click Copy to all , then click OK to apply the parameter settings to cameras of all channels. ----End 5.4 Video loss If a camera was disconnected, it will show video loss. Operation Description Click Menu in the upper left corner of the camera management screen and choose Video loss to access the video loss screen, as shown in Figure 5-5.

User Manual Camera Management 30 Issue V1.0 (2018-06-04) Figure 5-5 Encode Parameter screen Operation Steps Step 1 Enable video loss. Click next to Start video loss to enable video loss. Step 2 Set arming time. Click on the right of Processing method to access arming time setting screen of processing method, as shown in Figure 5-6.

User Manual Issue V1.0 (2018-06-04) 31 Figure 5-6 Arming time screen Step 3 Arming time setting： Method 1：Click left mouse button to select any time point within 0:00-24:00 from Monday to Sunday. Method 2：Hold down the left mouse button, drag and release mouse to select the arming time within 0:00-24:00 from Monday to Sunday. NOTE When you select time by dragging the cursor, the cursor cannot be moved out of the time area. Otherwise, no time can be selected. Method 3：Click in the arming time page to select the whole day or whole week. Deleting arming time: Click again or inverse selection to delete the selected arming time. Step 4 Set trigger channel. 1. Click Trigger channel tag to access trigger channel screen, as shown in Figure 5-7.

User Manual Camera Management 32 Issue V1.0 (2018-06-04) Figure 5-7 Trigger channel screen . 2. Select the trigger channel of current channel. 3. Click OK to save trigger channel settings or click Cancel to cancel the settings. Step 5 Set Processing method. 1. Click Processing method tag to access processing method screen, as shown in Figure 5-8.

User Manual Issue V1.0 (2018-06-04) 33 Figure 5-8 Processing method screen 2. Click of “Buzzer alarm”, Push message”, “Alarm message”, “Linkage record” respectively to enable or disable these function. 3. Click OK to save processing method settings or click Cancel to cancel the settings. Step 6 Click OK to save video loss settings or click Copy to all, then click OK to apply the video loss settings to cameras of all channels. ----End 5.5 Motion Detection Motion detection refers that an alarm is triggered when an image in a specified area changes. Operation Description Click Menu in the upper left corner of the camera management screen and choose Motion Detection to access the Motion Detection screen, as shown in Figure 5-9.

User Manual Camera Management 34 Issue V1.0 (2018-06-04) Figure 5-9 Motion Detection screen Operation Steps Step 1 Select a camera in the camera list on the left side of the Motion Detection screen. Step 2 Click next to Start Motion Detection to enable motion detection. Step 3 In the video window, hold down and drag the left mouse button to draw a motion detection area. Step 4 Select a value from the drop-down list next to Sensitivity. Step 5 Click next to Processing method to access processing method screen. For details, please see Step 2~Step 5. Step 6 Click OK to save motion detection settings or click Copy to all, then click OK to apply the motion detection settings to cameras of all channels.  After a motion detection area is selected, you can double-click it to delete the selected area.  A maximum of four areas can be configured. ----End

User Manual Issue V1.0 (2018-06-04) 35 5.6 Privacy Area The system allows you to mask images in a specified area and this area is called privacy area. Operation Description Click Menu in the upper left corner of the camera management screen and choose Privacy area to access the Privacy area screen, as shown in Figure 5-10. Figure 5-10 Privacy Area screen Operation Steps Step 1 Select a camera in the camera list on the left side of the Privacy area screen. Step 2 In the video window, hold down and drag the left mouse button to draw a privacy area. Step 3 Click OK to save privacy area settings or click Copy to all, then click OK to apply the privacy area settings to cameras of all channels. ----End 5.7 Camera tamper Camera Tamper refers to the occurrence of tampered or shifted in video image. An alarm is generated if such an event occurs.

User Manual Camera Management 36 Issue V1.0 (2018-06-04) Operation Description Click Menu in the upper left corner of the camera management screen and choose Camera tamper to access the Camera tamper screen, as shown in Figure 5-11. Figure 5-11 Camera tamper screen Operation Steps Step 1 Select a camera in the camera list on the left side of the camera tamper screen. Step 2 Click next to Start camera tamper to enable camera tamper. Step 3 Click next to Processing method to access processing method screen. For details, please see Step 2~Step 5. Step 4 Click OK to save camera tamper settings or click Copy to all, then click OK to apply the camera tamper settings to cameras of all channels. ----End 5.8 OSD settings Click Menu in the upper left corner of the camera management screen and choose Setup OSD to access the OSD setting screen, as shown in Figure 5-12.

User Manual Issue V1.0 (2018-06-04) 37 Figure 5-12 OSD setting screen Operation Steps Step 1 Select a camera in the camera list on the left side of the OSD setting screen. Step 2 Click next to Time to enable or disenable OSD time setting. Step 3 Click next to Channel to enable or disenable OSD channel setting. Step 4 Click OK to save OSD settings or click Copy to all ,then click OK to apply the OSD settings to cameras of all channels. In the video window, click and drag time or channel to move to a location.

User Manual System setting 38 Issue V1.0 (2018-06-04) 6 System setting The system setting allows you to set basic information, network, record, output, alarms manager, disk, privacy manager, advanced setting, and App for the system in System Setting. Figure 6-1 shows the system setting screen. Figure 6-1 System setting screen 6.1 Basic The system allows you to view the firmware version, compile time and product model, set the device name, display resolution, system language, time zone, time and date and DST in Basic.

User Manual Issue V1.0 (2018-06-04) 39 6.1.1 System Operation Steps Step 1 On the System setting screen, choose Basic > System to access the System setting screen, as shown in Figure 6-2. Figure 6-2 System setting screen Step 2 Enter Device name for selected device. Step 3 Select a proper resolution from the Display drop-down list based on the adopted monitor. Step 4 Select a required language from the Language drop-down list. Step 5 Click OK to save system settings or click Cancel to cancel settings. ----End 6.1.2 Time Operation Steps Step 1 On the System setting screen, choose Basic > Time to access the time setting screen, as shown in Figure 6-3.

User Manual System setting 40 Issue V1.0 (2018-06-04) Figure 6-3 Time setting screen Step 2 Select a required date format from the Date Format drop-down list. Step 3 Click next to 24 Hour to disable the 24-hour system. Then, the 12-hour system is enabled. If 24 Hour is set to On, the 24-hour system is used and is enabled by default. Step 4 Click next to Sync Time to disable time synchronization. Time synchronization is enabled by default. Time is synchronized with the PC time. Step 5 After Sync Time is disabled, you can manually set the system time: Click Date and scroll the mouse scroll wheel to select the year, month, and date. 1. Click Time and scroll the mouse scroll wheel to select the hour, minute, and second. 2. Click Modify Time to save the time settings. Step 6 Click OK to save settings or click Cancel to cancel settings. ----End 6.1.3 Time zone Operation Steps Step 1 On the System setting screen, choose Basic > Time zone to access the time zone setting screen, as shown in Figure 6-4.

User Manual Issue V1.0 (2018-06-04) 41 Figure 6-4 Time zone setting screen Step 2 Select a required time zone from the Time Zone drop-down list. Step 3 Click OK to save settings or click Cancel to cancel settings. ----End 6.1.4 DST When the DST start time arrives, the device time automatically goes forward one hour. When the DST end time arrives, the device time automatically goes backward one hour. Operation Steps Step 1 On the System setting screen, choose Basic > DST to access the DST setting screen, as shown in Figure 6-5.

User Manual System setting 42 Issue V1.0 (2018-06-04) Figure 6-5 DST setting screen Step 2 Click next to Daylight saving time to enable DST. Step 3 Select start time, end time, offset time from the drop-down list respectively. Step 4 Click OK to save settings or click Cancel to cancel settings. ----End 6.2 Network 6.2.1 Ipv4 IPv4 is the IP protocol that uses an address length of 32 bits. Operation Steps Step 1 On the System setting screen, choose Network > IPv4 to access the Ipv4 setting screen, as shown in Figure 6-6.

User Manual Issue V1.0 (2018-06-04) 43 Figure 6-6 Ipv4 setting screen Step 2 Click next to Obtain IP automatically to enable or disable the function of automatically getting an IP address. The function is enabled by default. If the function is disabled, click input boxes next to IP, Netmask, and Gateway to set the parameters as required. Step 3 Click next to Obtain DNS Automatically to enable or disable the function of automatically getting a DNS address. The function is enabled by default. If the function is disabled, click input boxes next to DNS1 and DNS2, delete original addresses, and enter new addresses. Step 4 Click Check. The system automatically checks network settings and the dialog box as shown in Figure 6-7 is displayed. Check and connect the network based on network check results.

User Manual System setting 44 Issue V1.0 (2018-06-04) Figure 6-7 Network check screen Step 5 Click OK to save IPv4 network settings or click Cancel to cancel settings. ----End 6.2.2 Port Operation Steps Step 1 On the System setting screen, choose Network > PORT to access the port setting screen, as shown in Figure 6-8.

User Manual Issue V1.0 (2018-06-04) 45 Figure 6-8 Port setting screen Step 2 Set HTTP port, Data port1 and Data port2 respectively. Step 3 Click OK to save settings or click Cancel to cancel settings.  Data Port1 used as RTSP port  Data Port2 used as video control port  After Ports is set and saved ,please click OK and Reboot. the port is set successfully. ----End 6.2.3 UPNP Operation Steps Step 1 On the System setting screen, choose Network > UPNP to access the port mapping setting screen, as shown in Figure 6-9.

User Manual System setting 46 Issue V1.0 (2018-06-04) Figure 6-9 Port mapping setting screen Step 2 Click next to UPNP to enable or disable the function of UPNP. The function is enabled by default. Step 3 After UPNP is disabled, you can manually set the HTTP port and Data port1. Step 4 Click OK to save settings or click Cancel to cancel settings.  After UPNP button is enabled, System perform port mapping automatically.  If UPNP is set OFF, you need to forward the ports by manually on router. ----End 6.2.4 SMTP If the Simple Mail Transfer Protocol (SMTP) function is enabled, the device automatically sends alarm information to specified email addresses when an alarm is generated. Operation Steps Step 1 On the System setting screen, choose Network > SMTP to access the SMTP setting screen, as shown in Figure 6-10.

User Manual Issue V1.0 (2018-06-04) 47 Figure 6-10 SMTP setting screen Step 2 Click next to SSL to enable or disable the function of SSL. The function is disabled by default. Step 3 Set SMTP server and SMTP server port manually. Step 4 Set sender E-mail, user name and password manually. Step 5 Set E-mail for receive alarm. the message “Mail has been sent, please check” is displayed. Open the mail, if the verification code is received, that shows the E-mail is set successfully. Step 6 Set E-mail for retrieve the password. the message “Mail has been sent, please check” is displayed. Open the mail, Step 7 if the verification code is received, that shows the E-mail is set successfully. Step 8 Click OK to save settings or click Cancel to cancel settings. ----End 6.2.5 DDNS Connect the specified camera to the Internet, and obtain the user name and password for logging into the Dynamic Domain Name System (DDNS) server. Operation Steps Step 1 On the System setting screen, choose Network > DDNS to access the DDNS network setting screen, as shown in Figure 6-11.

User Manual System setting 48 Issue V1.0 (2018-06-04) Figure 6-11 DDNS setting screen Step 2 Click the button next to Enable to enable the DDNS function. It is disabled by default. Step 3 Select a required value from the Protocol drop-down list. Step 4 Click OK to save DDNS network settings or click Cancel to cancel settings. An external network can access an address specified in the DDNS settings to access the DVR. ----End 6.2.6 Blacklist Set the IP address in specified network segment to allow access or prohibit access. Operation Steps Step 1 On the System setting screen, choose Network > Blacklist to access the blacklist setting screen, as shown in Figure 6-12.

User Manual Issue V1.0 (2018-06-04) 49 Figure 6-12 Blacklist screen Step 2 Click next to Blacklist to enable or disable the function of blacklist. The function is disabled by default. Step 3 Select a required value from the rule type drop-down list. Step 4 Click Add, the set the black and white list IP segment screen is displayed, as show in Figure 6-13. Figure 6-13 IP Address Segment screen 2. Enter value manually for Start IP address, end IP address. 3. Click OK. The system saves the settings. And the black and white list IP segment listed in the black (white) list.

User Manual System setting 50 Issue V1.0 (2018-06-04)  Blacklist: IP address in specified network segment to prohibit access.  Whitelist: IP address in specified network segment to allow access  Select a name in the list and click Delete to delete the name from the list.  Select a name in the list and click Edit to edit the name in the list.  Only one rule type is available, and the last rule type set is efficient. ----End 6.3 Record Operation Steps Step 1 On the System setting screen, choose Record to access the record screen, as shown in Figure 6-14. Figure 6-14 Record setting screen Step 2 Click next to Enable schedule record to enable or disable the function of schedule record. The function is enabled 7*24 recording by default. Step 3 Set Schedule. For details, please see Step 2~Step 5. Step 4 Click OK to save record settings or click Cancel to cancel settings. ----End

User Manual Issue V1.0 (2018-06-04) 51 6.4 Output Operation Steps Step 1 On the System setting screen, choose Output to access the output setting screen, as shown in Figure 6-15. Figure 6-15 Output setting screen Step 2 Click next to Dwell time to access the dwell time screen, as shown in Figure 6-16.

User Manual System setting 52 Issue V1.0 (2018-06-04) Figure 6-16 Dwell time screen 2. Select a required value from the Dwell interval drop-down list. 3. Set layout. Click to choose layout. 4. Select dwell channel. Click the video window and select a channel from the channel list to set the dwell channel. 5. Click OK to save dwell settings or click Cancel to cancel settings. Step 3 Click next to CVBS output settings to access CVBS output settings screen, as shown in Figure 6-17.

User Manual Issue V1.0 (2018-06-04) 53 Figure 6-17 CVBS output settings screen 2. Set the display offset. Press and hold the left mouse button and drag the value bar to set the left, up, right, down display offset of the CVBS monitor. 3. Set the display colour. Click Display colour tag to access the display colour screen, as shown in Figure 6-18.

User Manual System setting 54 Issue V1.0 (2018-06-04) Figure 6-18 Display colour settings screen 4. Press and hold the left mouse button and drag the value bar to set the brightness, contrast, chroma, saturation of the CVBS monitor. 5. Click OK to save CVBS output settings or click Cancel to cancel settings. 6.5 Alarm Manager The system allows you to set alarm surveillance and alarm in in Alarm manager. 6.5.1 Surveillance Operation Steps Step 1 On the System setting screen, choose Alarm manager > Surveillance to access the surveillance setting screen, as shown in Figure 6-19.

User Manual Issue V1.0 (2018-06-04) 55 Figure 6-19 Surveillance setting screen Step 2 Click next to Enable to enable the surveillance function. Step 3 Select alarm duration from the drop-down list. Step 4 Click OK to save surveillance settings or click Cancel to cancel settings. ----End 6.5.2 Alarm in Operation Steps Step 1 On the System setting screen, choose Alarm manager > Alarm in to access the alarm in setting screen, as shown in Figure 6-20.

User Manual System setting 56 Issue V1.0 (2018-06-04) Figure 6-20 Alarm in setting screen Step 2 Select a channel in alarm in. Step 3 Click next to Enable to enable or disable the functions. Step 4 Select Alarm type from the drop-down list.  NC: Closed alarm circuit  NO: Opened alarm circuit Step 5 Set name. Step 6 Set Processing method. For details, please see Step 2~Step 5. Step 7 Click OK to save alarm in settings or click Cancel to cancel settings. ----End 6.6 Disk The system allows you to view the total capacity, used capacity, and SNs of disks, and clear all video data in a disk in disk management.

User Manual Issue V1.0 (2018-06-04) 57 6.6.1 Viewing Disk Information Operation Steps Step 1 On the System setting screen, choose Disk to access the disk management screen, as shown in Figure 6-21. Figure 6-21 Disk management screen Step 2 You can view the total capacity, used capacity, and SN of a disk on the disk management screen. ----End 6.6.2 Clearing Disk Data Click Clear in the lower part of the disk management screen. A message, indicating that all video data will be cleared and asking you whether to continue the operation, is displayed. Click OK to delete all video data on the disks. You should clear the disk data when the disk is installed to the DVR for the first time.

User Manual System setting 58 Issue V1.0 (2018-06-04) 6.7 Privilege manager 6.7.1 User manager Operation Steps Step 1 On the System setting screen, choose Privilege manager > User manager to access the user management screen, as shown in Figure 6-22. Figure 6-22 User manager screen Step 2 Add or delete a user.  Adding a user 1. Click Add. The Add User dialog box appears, as shown in Figure 6-23.

User Manual Issue V1.0 (2018-06-04) 59 Figure 6-23 Add user screen 2. Enter a username, password and confirm password.  The password should include letter, character and number.  The password should be 6~32. 3. Select a Group from the drop-down list box. 4. Select the operation privileges in the list of the add user screen. 5. Click OK. The user is set successfully.  The default user is Administrator and cannot be deleted or modified.  Select a user from user list to edit or delete user. Step 3 Click OK to save user manager settings or click Cancel to cancel settings. -----End

User Manual System setting 60 Issue V1.0 (2018-06-04) 6.7.2 Modify Password Operation Steps Step 1 On the System setting screen, choose Privilege manager > Modify password to access the modify password screen, as shown in Figure 6-24. Figure 6-24 Password modification screen Step 2 Enter the correct old password, new password, and confirm password, and click Modify. The password is modified successfully.  The password should include at least two kinds of letter, character and number.  The password should be 6~32. Step 3 Click OK to save modify password settings or click Cancel to cancel settings. ----End 6.8 Privacy Operation Steps Step 1 On the System setting screen, choose Privilege manager > privacy to access the privacy screen, as shown in Figure 6-25.

User Manual Issue V1.0 (2018-06-04) 61 Figure 6-25 Privacy screen Step 2 Click next to Enable password to enable or disable the function. The function is enabled by default. Step 3 Click OK to save enable password settings or click Cancel to cancel settings. ----End 6.9 Advanced setting Operation Steps Step 1 On the System setting screen, choose Advanced setting to access the advanced setting screen, as shown in Figure 6-26.

User Manual System setting 62 Issue V1.0 (2018-06-04) Figure 6-26 Advanced setting screen Step 2 Click Import to import the configuration. Step 3 Click Export to export the configuration. Step 4 Click Reset, Reboot, Shutdown to reset the DVR, reboot the DVR or Shutdown the DVR if you need. Step 5 Click OK to save enable password settings or click Cancel to cancel settings. ----End 6.10 App You can use application software that supports QR code scanning to scan the QR code in App to download the application for mobile phones. Then, you can perform operations on the DVR by using the App. Operation Description On the System setting screen, choose App to access the mobile phone App screen, as shown in Figure 6-27.

User Manual Issue V1.0 (2018-06-04) 63 Figure 6-27 Mobile phone App screen QR codes are described as follows: iOS QR code: used by iOS-based devices to download the App client. Android QR code: used by Android-based devices to download the App client. UUID QR code: After the mobile phone App is installed, you can scan the UUID QR code to add an DVR. ----End

User Manual Log Center 64 Issue V1.0 (2018-06-04) 7 Log Center The system allows you to set and view records of any operations performed on the DVR in Log Center, including power-on, parameter settings, and camera management. Operation Steps Step 1 Click Log Center in the main menu to access the Log Center screen, as shown in Figure 7-1. Figure 7-1 Log Center screen Step 2 Select an object whose logs need to be queried on the left side of the Log Center screen. The logs include system logs and logs of a camera in a channel. Step 3 Set the log start time and end time on the right side of the Log Center screen. Step 4 Click Inquire to query logs. Step 5 Double-click a log to play the video generated at the log time point, as shown in Figure 7-2.

User Manual Issue V1.0 (2018-06-04) 65 Figure 7-2 Log play screen Step 6 Click Export log to export logs to USB storage.. ----End

User Manual Alarm 66 Issue V1.0 (2018-06-04) 8 Alarm The system allows you to view alarm events, set the timeline, and clear alarms in Alarm. 8.1 Event Operation Steps Step 1 Click Alarm in the main menu to access the Event Center screen, as shown in Figure 8-1. Figure 8-1 Event Center screen Step 2 Select a camera or all cameras on the left side of the Event Center screen. Step 3 Select the event type below Event in the lower right part of the Event Center screen. All event types are selected by default. You can click one event type to deselect it. Step 4 Set the alarm start time and end time in the upper right part of the Event Center screen. Step 5 Click Refresh to query alarm events. Step 6 Double-click an alarm event to play the alarm video, as shown in Figure 8-2.

User Manual Issue V1.0 (2018-06-04) 67 Figure 8-2 Alarm video play screen ----End 8.2 Timeline The system allows you to set the timeline to play alarm videos presented by time on each day of a week. Operation Steps Step 1 Choose Alarm > Timeline in the main menu to access the Timeline screen, as shown in Figure 8-3.

User Manual Alarm 68 Issue V1.0 (2018-06-04) Figure 8-3 Timeline screen Step 2 Select the alarm time to view the alarm records on that day. Step 3 Double-click an alarm picture to play the alarm video. ----End 8.3 Clear alarm When the buzzer beeps, click Clear alarm in the main menu to clear the alarm. ----End

User Manual Issue V1.0 (2018-06-04) 69 9 Web Access The DVR is embedded with a web server and supports mainstream browsers such as Internet Explorer, Chrome, Firefox, and Safari. Operations such as quick setup, real- time preview, video playback, alarm search, DVR setup, and camera setup can be performed through the web. 9.1 Login The default IP address of the DVR is 192.168.0.121 when network interface 1 is used and is 92.168.0.121 when network interface 2 is used. To access the DVR, enter the corresponding IP address in the address bar of your web browser. If the DVR is connected through network interface 1, enter http://1 92.168.0.121.  Before accessing the DVR through the web, ensure that the network connection is correct and smooth.  Identify the connected network interface and enter the corresponding IP address in the address bar of your browser. Figure 9-1 shows the web-based login interface of the DVR. Figure 9-1 Login interface of the DVR

User Manual Web Access 70 Issue V1.0 (2018-06-04) Enter your user name and password to access the main interface. The default user name and password are both admin. 9.2 Live Video On the Live Video interface, you can select an online camera in the left Cameras pane and view the corresponding live video. Click Live Video. The Live Video interface appears, as shown in Figure 9-2. Figure 9-2 Live Video interface 9.3 Video Playback Video playback refers to playing of videos stored in local hard disks. Operation Operation Steps Step 1 Click in the function navigation bar, the video playback interface is displayed, , as shown in Figure 9-3.

User Manual Issue V1.0 (2018-06-04) 71 Figure 9-3 Playback interface Step 2 Select a camera. Click a camera in the device list. A selected device is marked with . An unselected device is marked with . Step 3 Select a date. Current date is displayed automatically. Click and to change the date. indicates that there are videos captured on that day. Step 4 Display videos. After a camera and date are selected, video information is displayed below the video pane. The time scale above the file axis shows the different time points of video recording. The time in blue in the middle is the time of the video being played. The file axis displays videos. Red file axis indicates a video exits, blank file axis indicates no video exits. Step 5 Play a video. You can play a video after selecting a device and date. Figure 9-4 shows the control bar of video playback, Table 9-1 describes the operations.

User Manual Web Access 72 Issue V1.0 (2018-06-04) Figure 9-4 Control bar Table 9-1 Playback button Buttons Button description How to operate Pause Click button to pause to play the video. Speed + Double increasing speed play when you click the button. A maximum of 32X can be configured. Normal Speed Click button to quick return to normal speed. Speed - Double decreasing speed play when you click the button. A minimum of 1/4X can be configured. Split screen Click button to switch the 1 screen and 4 screens. Zoom in Click button to play video in a bigger time scale. Zoom out Click button to play video in a smaller time scale.. ----End 9.4 Alarm Search You can retrieval the channel alarm and system alarm in the retrieval interface. Operation Steps Step 1 Click Alarm Search in the navigation bar at the top of the web interface. The Alarm Search interface appears, as shown in Figure 9-5.

User Manual Issue V1.0 (2018-06-04) 73 Figure 9-5 Alarm Search interface Step 2 Click at the top right conner, set the channel, type,start time and end time, as shown in Figure 9-6 Figure 9-6 Channel alarm Step 3 Click OK, the result will be displayed as shown in Figure 9-7

User Manual Web Access 74 Issue V1.0 (2018-06-04) Figure 9-7 Retrieval result  Click to select the page of alarm list..  shows the rows shown in every page..  The system alarm retrieval is same as channel alarm. 9.5 DVR Setting Click DVR Setup in the navigation bar at the top of the web interface. The DVR Setup interface appears, as shown in Figure 9-8.

User Manual Issue V1.0 (2018-06-04) 75 Figure 9-8 DVR Setting interface 9.5.1 Viewing basic information You can view time, time zone, DST (Daylight saving time) and device language in basic interface. Operation Steps Step 1 On the System Setting screen, choose System > Basic setting to access the Basic interface, as shown in Figure 9-9.

User Manual Web Access 76 Issue V1.0 (2018-06-04) Figure 9-9 Basic interface Step 2 Click Time, Time zone, DST, Device language to view these basic information.. ----End 9.5.2 Network management You can set IPv4, port, DDNS, SMTP in network management interface. 9.5.2.1 IPv4 IPv4 is the IP protocol that uses an address length of 32 bits. Operation Steps Step 1 On the System Setting screen, choose System >Network management to access the IPv4 interface, as shown in Figure 9-10.

User Manual Issue V1.0 (2018-06-04) 77 Figure 9-10 IPv4 interface Step 2 Click next to Obtain IP automatically to enable or disable the function of automatically getting an IP address. The function is enabled by default. If the function is disabled, click input boxes next to IP, Netmask, and Gateway to set the parameters as required. Step 3 Click next to Obtain DNS Automatically to enable or disable the function of automatically getting a DNS address. The function is enabled by default. If the function is disabled, click input boxes next to DNS1 and DNS2, delete original addresses, and enter new addresses. Step 4 Click Apply to save the settings. ----End 9.5.2.2 Port Operation Steps Step 1 Click PORT label to enter the port setting interface, as shown in Figure 9-11

User Manual Web Access 78 Issue V1.0 (2018-06-04) Figure 9-11 Port setting interface Step 2 Set HTTP port, Data port1 and Data port2 respectively. Step 3 Click Apply to save settings.  Data Port1 used as RTSP port  Data Port2 used as video control port  After Ports is set and saved ,please click OK and Reboot. the port is set successfully. ----End 9.5.2.3 DDNS Operation Steps Step 1 Click DDNS label to enter the DDNS setting interface, as shown in Figure 9-12

User Manual Issue V1.0 (2018-06-04) 79 Figure 9-12 DDNS setting interface Step 2 Click the button to enable the DDNS function. It is disabled by default. Step 3 Select a required value from the Protocol drop-down list. Step 4 Set Domain name, Account, and Password. Step 5 Click Apply to save DDNS network settings. An external network can access an address specified in the DDNS settings to access the DVR. ----End 9.5.2.4 SMTP Operation Steps Step 1 Click SMTP label to enter the SMTP setting interface, as shown in Figure 9-13.

User Manual Web Access 80 Issue V1.0 (2018-06-04) Figure 9-13 SMTP setting interface Step 2 Click next to SSL to enable Secure Sockets Layer( Some SMTP servers are required). It is disabled by default. Step 3 Set SMTP server and SMTP server port manually. Step 4 Set sender E-mail, user name and password manually. Step 5 Set E-mail for receive alarm. the message. Step 6 Set E-mail for retrieve the password. the message . Step 7 Click Apply to save settings. 9.5.3 Device management You can reboot, upgrade and reset the NVR in device management interface. On the System Setting screen, choose System > Device management to access the Device management interface, as shown in Figure 9-14. Table 9-2describes the operations.

User Manual Issue V1.0 (2018-06-04) 81 Figure 9-14 Device management interface Table 9-2 Device management operations Buttons Button description How to operate Reboot (1) Click , the message “Are you sure to restart?” is displayed. (2) Click OK and the NVR reboot. Upgrade (1) Click and select an upgrade package. (2) The message “Upgrade success! The device is rebooting，please login later!” is displayed. (3) NVR reboot and enter to login interface.

User Manual Web Access 82 Issue V1.0 (2018-06-04) Buttons Button description How to operate Reset (1) Click , the message “Are you sure to restore?” is displayed. (2) Click OK, the message “Apply success! The device is rebooting, please login later!” is displayed. (3) NVR reboot and enter to login interface. Close (1) Click , the message “Confirm closed?” is displayed. (2) Click OK, the message “The device has been closed !” is displayed. (3) NVR is closed. ----End 9.6 Alarm You can set motion alarm in alarm interface. Operation Steps Step 1 On the System Setting screen, choose Alarm >Channel Alarm to access the motion alarm interface, as shown in Figure 9-15.

User Manual Issue V1.0 (2018-06-04) 83 Figure 9-15 Motion Alarm interface Step 2 Select a channel from the drop-down list. Step 3 Click to enable channel alarm . It is disabled by default. Step 4 Drag the slider to set the sensitivity. Step 5 Set the alarm events. 1. Click Event in channel alarm interface. 2. Click the button of alarm events to enable or disable the events. The alarm events include push message, alarm message, E-mail push, buzzer, alarm out and channel record. 3. Click Apply to save the setting or Click Copy to and select one or more channels to copy the settings to the selected channels. Step 6 Set linkage channel. 1. Click Channel in channel alarm interface. 2. Select one or more channels to set the linkage with current channel. 3. Click Apply to save the setting or Click Copy to and select one or more channels to copy the settings to the selected channels.

User Manual Web Access 84 Issue V1.0 (2018-06-04) Step 7 Set time plan. 1. Click Time plan in channel alarm interface, the time plan interface is display, as shown in Figure 9-16 Figure 9-16 Time plan interface 2. Set the time plan. Method 1：Click left mouse button to select any time point within 0:00-24:00 from Monday to Sunday. Method 2：Hold down the left mouse button, drag and release mouse to select the schedule within 0:00-24:00 from Monday to Sunday. NOTE When you select time by dragging the cursor, the cursor cannot be moved out of the time area. Otherwise, no time can be selected. Method 3：Click in the schedule page to select the whole day or whole week. Deleting deployment time: Click again or inverse selection to delete the selected schedule. Step 8 Click Apply to save the setting or Click Copy to and select one or more channels to copy the settings to the selected channels. 9.7 Storage You can configure record policy in storage interface. Operation Steps Step 1 On the System Setting screen, choose Storage > Record policy to access the Record policy interface, as shown in Figure 9-17.

User Manual Issue V1.0 (2018-06-04) 85 Figure 9-17 Record policy interface Step 2 Click to enable schedule record. It is enabled by default. Step 3 Set the record policy. Please refer to 9.6 Step 7 Set time plan. Step 4 Click Apply to save the setting. ----End 9.8 User You can add, modify, and delete a user and privilege in user manager interface. 9.8.1 Privilege management Operation Steps Step 1 On the System Setting screen, choose User > Privilege management to access the Privilege management interface, as shown in Figure 9-18

User Manual Web Access 86 Issue V1.0 (2018-06-04) Figure 9-18 Privilege management interface Step 2 Add a user. 1. Click in privilege management interface to access the add user interface, as shown in Figure 9-19

User Manual Issue V1.0 (2018-06-04) 87 Figure 9-19 Add user interface 2. Set the user name, password, and confirm password. 3. Select a group from the drop-down list. 4. Check the privilege. 5. Click OK to save the setting or Click cancel to cancel the setting. NOTE  Click to view the privilege of super administrator.  Click to modify the user and privilege of operator and media user in the user list..  Click to delete the user in the user list. ----End

User Manual Web Access 88 Issue V1.0 (2018-06-04) 9.8.2 Modify password Operation Steps Step 1 On the System Setting screen, choose User > Modify password to access the Modify password interface, as shown in Figure 9-20. Figure 9-20 Modify password interface Step 2 Enter the old password, and set the new password and confirm password. Step 3 Click Apply, the password is modified successfully, the system return to the login interface. ----End 9.8.3 Local You can set the image download path for snapshot and the record download path for record files in the download configuration interface. Operation Steps Step 1 On the System Setting screen, choose Local > Download Config to access the Download configuration interface, as shown in Figure 9-21.

User Manual Issue V1.0 (2018-06-04) 89 Figure 9-21 Download configuration interface Step 2 Enter the image download path. Step 3 Enter the record download path. Step 4 Click Apply to save the setting. -----End

User Manual FAQ 90 Issue V1.0 (2018-06-04) 10 FAQ 1. Why is the DVR self-test screen frozen? Use the methods below to fix the problem: Method 1: Check whether the DVR is equipped with a hard disk. Method 2: Check whether the DVR is equipped with an unformatted hard disk. Method 3: Check whether the hard disk is damaged. If a hard disk is not required, Click continue in the lower right corner of the screen to resume the startup process. 2. Why does the screen display incomplete information or is skewed? Use the following methods below to fix the problem: Method 1: Use the automatic adjustment function of the monitor. Method 2: Click Adjust on the login screen. The Monitor Setup screen is displayed. For operation details, see chapter 4 "Operation Instruction" of the Network Video Recorder (DVR) User Guide. 3. Why no image is displayed on the monitor? Use the following methods below to fix the problem: Method 1: Check the power supply of the monitor. Method 2: Check whether the monitor is connected to the DVR correctly. Method 3: Restart the DVR. Method 4: Check whether the monitor supports the default resolution (1024×768) of the DVR.