VETRON 5300 Instruction Book

Clara-Immerwahr-Str. 6 67661 Kaiserslautern, Germany Tel.: +49 6301 320 75 - 0 Fax: +49 6301 320 75 - 11 [email protected] www.vetrontypical.com All rights reserved. The instructions for use, service instructions, parts lists are protected by copyright. Any reuse of the content outside the copyright is without the written consent of VETRON | Typical GmbH inadmissible and punishable. VETRON | Typical GmbH is only liable for damage caused by intent or gross negligence on the part of the manufacturer. Otherwise, liability is excluded. Reserve technical changes! The contents were carefully prepared and checked by the publisher. Due to continuous development, illustrations, functional steps and technical data may difer slightly. Updating the documentation If you have suggestions for improvement or have detected any irregularities, please contact us. The documents for the machines can be accessed by logging on https://www.vetrontypical.com/ downloaded for free. CE marked after §7 Prod SG

INDEX VETRON 5300 - POST BED MACHINE 01. PREFACE 05 01. SAFETY INSTRUCTIONS 06 02. SYMBOLISM 07 03. DANGER NOTES 08 04. PRODUCT INTRODUCTION / INTENDED USE / CONFORMITY DECLARATION 09 05. TECHNICAL DATA 10 06. TRANSPORT - PACKAGING - DISPOSAL - STORAGE | FIRST COMMISSIONING / DECOMMISSIONING 11 07. MOUNTING SAFETY DEVICES FOR TILTING (CYLINDER) 12 07.01. SAFETY DEVICES FOR TILTING (CHAIN) 13 07.02. SAFETY DEVICES FOR TILTING (SAFETY SPRING) 02. MACHINE DESCRIPTION 15 01. OVERVIEW 16 02. OPERATING PANEL 17 03. HOTKEYS 18 04. ELECTRONIC HANDWHEEL & REVERSE SEWING 19 05. CONTROL & MAIN SWITCH 20 06. PEDAL 21 07. LIGHT 22 08. MACHINE START 23 09. PROGRAM CHANGE 24 10. DIRECT ACCESS

03. OPERATION OF THE MACHINE 25 01. INSERTING THE NEEDLE (1- NEEDLE) 26 01.01. INSERTING THE NEEDLE (2- NEEDLE) 27 02. SEWING FEET EXCHANGE 28 03. THREADING THE MACHINE (1- / 2- NEEDLE) 29 04. EXCHANGING THE BOBBIN AND ADJUSTING THE BOBBIN THREAD TENSION 30 05. WINDING THE BOBBIN THREAD 31 06. ENGAGING THE SAFETY CLUTCH 32 07. SAFETY SPRING 04. MAINTENANCE 33 01. MAINTENANCE INTERVALS 34 02. OIL LEVEL CHECK 35 03. CLEANING THE MACHINE 36 04. SEWING DRIVE 37 05. PNEUMATIC SYSTEM 05. PROGRAMMING 39 01. GENERAL 40 02. CREATE PROGRAMNAME AND STORING 41 03. CHANGE PROGRAM NAME 42 04. PROGRAM PARAMETER 06. WEAR PARTS 69 01. GENERAL INFORMATION 70 02.01. LISTING 07. WIRING DIAGRAM 73 01. VETRON 8340 CONTROL BOX INDEX VETRON 5300 - POST BED MACHINE

01. PREFACE 01. SAFETY INSTRUCTIONS General Safety Instructions This manual and the warning symbols on the machine should en- sure the safe use of the machine, so that no accidents and injuries may occur to you and others. Please read this instruction and also the safety instructions of the motor manufacturer carefully. » The machine must only be operated in accordance with its intended purpose (for example, sewing medium to heavy ma- terials such as jeans, leather, etc. NO tin!) and with the as- sociated protective equipment. The relevant country-specific safety regulations and technical data must also be observed. » The machine should only be used in accordance with its inten- ded purpose (eg sewing medium to heavy materials such as jeans, leather, etc.) and with the associated protective equip- ment. The relevant country-specific safety regulations and the technical data must also be observed. » The machine should only be set up and operated in dry and well-kept rooms. » Do not place the machines outdoors, next to radiators or heat source. The ambient temperature should not be lower or hig- her than between 0° C to 45° C. » The machine must only be commissioned after the relevant operating instructions have been taken into consideration and by appropriately instructed operators. » These instructions are to be stored at hand. » The connection cable must be provided with a country- specific approved mains plug. The mains plug must only be connected to grounded sockets. Here a qualified specialist is necessary. » The machine must always have a grounding. Only over this is a normal operation of the machine to ensure. » The danger and safety instructions attached to the machine must be followed. » When replacing sewing tools such as needle, sewing foot, stitch plate, feed dog or bobbin, when threading, when leaving the workplace and during maintenance, etc., the machine must be disconnected from the mains.    Press the main switch or pull out the mains plug. » Machines with compressed air components must be discon- nected from the compressed air supply and the residual pres- sure released before repair or maintenance work. Exceptions to this are performance tests or specific settings. » Repairs and all maintenance work should only be carried out by qualified personnel or appropriately instructed persons. » Work on electrical equipment must only be carried out by qualified specialists.  If errors are detected, stop the machine immediately. » Work on parts and equipment that are live is not permitted. The machine must be disconnected from the mains. » Modifications or modifications to the machine must be carried out in compliance with all relevant safety regulations. The manufacturer assumes no responsibility for damage caused by changes or modifications. » For repairs, only spare parts approved by VETRON may be used. In case of infringement the guarantee expires. » The machines are to be used only for the purpose intended. » If oils, greases, etc., used for the machines and accessories, get in your eyes or on your skin, or should you swallow any of these fluids, wash them immediately and thoroughly, or seek medical attention immediately. » Commissioning of the machine is prohibited until it has been determined that the entire sewing unit complies with the pro- visions of the EC directive and the declaration of conformity has been created. Advice to the Owner » As part of the machine, this operating manual must be availab- le to operating personnel at all times. Before using the machine for the first time, the operator must read this operating manual. » The operator has to ensure that the machine is only operated in perfect condition. » The operator must ensure that no safety devices are removed or disabled. » The operator must ensure that only authorized or properly in- structed persons work on the machine. » The operator must therefore ensure that the workstations ac- cording to ASR lux. 4 are adequately illuminated (min. 750 lux). Operators and Technical Staf » The operating personnel are responsible for setting up, ope- rating and cleaning the machine and responsible for the eli- mination of faults. » Qualified personnel include people with specialist trai- ning in electrical / electronics, pneumatics and mechanics.  Lubrication, maintenance, repair and adjustment are your responsibilities. » The operator must refrain from any operation that impaires the safety on the machine. 1. Jewelry, chains and rings - must not be worn. 2. The clothes should be tight 3. Only authorized persons may enter the danger area. » If changes occur to the machine that afect safety, they must be reported immediately to the operator. » The specialist personnel - persons with training in electrical / electronics and mechanics - are responsible for the lubrica- tion, maintenance, repair and adjustment of the machine. » Before starting adjustment and repair work, the main switch must be switched of and secured against reclosing. » Work on parts that are under tension should be avoided. Ex- ceptions are regulated by EN 50110. After maintenance and repair work, the protective covers must be replaced. » Operating and specialist personnel are obliged to observe the sa- fety instructions given in the instructions for use during all work.

01. PREFACE 02. SYMBOLISM DANGER! This symbol in combination with the word DANGER, indicates an imminent danger that may result in serious injury or death. WARNING! This symbol in combination with the word WARNING indicates a potentially hazardous situation which, if not avoided, could result in serious injury or death ATTENTION! This symbol in combination with the word ATTENTION may indicate a potentially hazardous situation that could result in minor personal injury. DANGER OF CUTS! This symbol indicates that there is an increased risk of cuts here. CRUSHING! This symbol indicates that there is a heightened risk of crushing RISK OF BURNS! This symbol indicates that there is an increased risk of burning here. MAGNET! This symbol indicates that there is a magnet field. INFORMATION! This symbol displays information. ADVICE! This symbol indicates important information. HARMFUL TO HEALTH! May damage certain organs. Can lead to immediate and long-term massive impairment of health, cause cancer, damage genetic material, fertility or development. May be fatal if infiltrated into the respiratory tract. HAZARD TO WATERS! May cause acute or long-term damage to aquatic organisms such as fish, aquatic insects and aquatic plants in low concentrations. PROTECTIVE EARTHING! Earthing one or more points of a network, installation or equipment for the purpose of electrical safety. 1 2 OFF ON DANGER LABEL Do not work the machine without finger guard and safety covers! Before threading, changing the needle, adjusting, changing the bobbin, cleaning, maintenance, etc. switch of the main switch on the control.

01. PREFACE 03. DANGER NOTES 1 THREAD TAKE UP LEVER 2 SEWING ZONE 3 BOBBIN THREAD WINDER 4 ZONE BETWEEN MACHINE AND TABLE CRUSHING Crushing and bruising through the thread take up lever 1 Make sure thread take up lever guard is mounted. Risk of injury due to movement of the lever. CRUSHING Crushing and bruising through the needle and sewing feet 2 Make sure finger guard is mounted. Risk of injury through needle and feet movement. DANGER OF CUTS Cuts through rotation 3 Keep distance from bobbin winder while winding. Risk of injury due to rotation. CRUSHING Crushing and bruising due to tilting the machine 4 Make sure safety spring 5 is mounted. Risk of injury when machine is tilted back. SAFETY PRECAUTIONS The eye protection 6 can be ordered optionally, but must not be removed after installation without consultation with the operator. The finger guard 7 must not be removed! 6 EYE GUARD 5 SAFETY SPRING 7 FINGER GUARD

1-/ 2-NEEDLE LOCKSTITCH SEWING MACHINE WITH DIRECT DRIVE AND TRIPLE FEED The consistent use of state-of-the-art control technology has made it possible to program all ma- chine parameters programmatically, making them directly accessible. This ensures that the process parameters are free from operator influence and after each setup. The innovative dynamic machine parameters based on the current speed and the permanent materi- al thickness measurement open up new paths in terms of processing quality, process reliability and reducing cycle times. Typical applications: Automotive Upholstery Suitcase Bag INTENDED USE Any use not approved by the manufacturer is considered improper! Proper use also includes compliance with the prescribed operating, adjustment, maintenance and repair measures. Damage due to non-intended use is not covered by the manufacturer‘s liability! The VETRON 5300 and its subclasses are 1- and 2- needle lockstitch sewing machine with direct drive and triple feed. Use the machines only according to their technical data and for medium to heavy materials such as jeans, leather, etc.. No tin! The machine is only intended for processing dry material and must not contain any hard objects. In this respect, the seam must be made with a thread whose requirement profile corresponds to the application purpose. The machine is designed for industrial use. The operator is obliged to carry out a risk assessment in accordance with the Work Protection Act (ArbSchG). CE-CONFORMITY DECLARATION All VETRON sewing machines comply with the applicable European regulations of relevant basic health and safety requirements, which are specified in the declaration of conformity and manufac- turer. 01. PREFACE 04. PRODUCT INTRODUCTION / INTENDED USE / CONFORMITY DECLARATION

Technical Data Vetron 5300 Stitch type 301 1- or 2-needle lockstitch with triple transport Needle system 134-35 Needle size 110-140 for sewing middle heavy materials Needle size 140-180 for sewing heavy materials Thread size 10/3 (depending on version) Max. Stitches/minutes 2500 Max. Stitch length 12mm Max. clearance under the sewing feet 20mm Max. top-feed-stroke 9mm Thread cutter for threads up to 10/3 Clearance space 350 x 130mm Table plate size 640 x 200mm Netto weight 70 kg Gross weight 104kg Operating voltage AC 220-240V / 50-60Hz Rated power 1200W Noise indication 80dB(A) Versions and subclasses can be found under: www.vetrontypical.com 01. PREFACE 05. TECHNICAL DATA

01. PREFACE 06. TRANSPORT - PACKAGING - DISPOSAL - STORAGE | FIRST COMMISSIONING / DECOMMISSIONING TRANSPORT - PACKAGING - DISPOSAL - STORAGE 01. Transport of the machine All machines are delivered packed. The product must be checked for shipping damage after delivery. For subsequent damage within the customer‘s operation, the manufacturer assumes no liability. Make sure that the products are transported safely and with the utmost care at your facility.  Moving machines with EHS (electrically height adjustable) with wheels: » Turn of the machine » Make sure that the sewing machine head is not tilted back » Put the table in the lowest position » Pull power and pneumatic connections » Release wheel brakes » Grab the table top and push the entire machine to the new location » Reconnect the electricity and pneumatics and tighten roller brakes 02. Packaging The packaging material must be disposed of in accordance with local environmental protection regulations. 03. Disposal The customer is responsible for the proper disposal. Disposal should comply with local envi- ronmental regulations. NOTE! Parts contaminated with lubricants or oils must be disposed of separately. 04. Storage When not in use for a long time, the machines must be protected against dirt, moisture and corrosion (e.g.: by an oil film). FIRST COMMISSIONING 01. Before operating the machine, clean the machine thoroughly. 02. Check whether the machine or electrical cables are damaged. 03. Have specialists confirm that you are allowed to operate the machine with the mains voltage and that it is correctly connected. 04. MACHINES WITH PNEUMATIC CONNECTIONS: Connect the machine to the compressed air system. The operating pressure at the filter valve is 6 bar. 05. All covers must be mounted. NOTE! 1.) Should deviations occur, do not operate the machine! 2.) Only connect the machine to a grounded power outlet! DECOMMISSIONING 01. Switch of the machine at the control. 02. Pull out the mains plug. 03. Disconnect the machine from the compressed air supply, if available. 04. Clean the machine if necessary. 05. If possible, cover the machine to avoid soiling.

01. PREFACE 07. MOUNTING SAFETY DEVICES FOR TILTING (CYLINDER) SAFETY CYLINDER 1 : » The safety cylinder 1 should be approx. 304mm to 310mm long. NOTE: If the cylinder is longer (max 310mm), the machine is moved further back. That means the machine is safer and more stable in this position. » If the machine is tilted back, the safety spring 3 must be locked securely. The distance bet- ween the table top and the spring must be at least 5mm (Picture 2). The distance can be adjusted on the cylinder by turning the fork head 2 in or out. If this is not enough, the cylinder carrier 4 must be readjusted. (Picture 3) HOW TO MOUNT THE SAFETY CYLINDER 1 : » Screw the cylinder carrier 4 under the table. The distance between the edge of the machine cutout and the cylinder carrier 4 is 205mm (minimum 203mm). » The distance between the cylinder carrier 4 and the edge of the machine cutout is 280mm. NOTE: The position of the safety cylinder is important for the stability of the machine. This must be checked when the machine is received. CRUSHING Crushing and bruising due to tilting the machine For diferent adjustments, the safety cylinder should be unhooked. Caution is advised, when returning the sewing machine to its original position. After work, reattach the safety cylinder WARNING! Work on safety devices must only be carried out by trained personnel!

01. PREFACE 07.01. SAFETY DEVICES FOR TILTING (CHAIN) HOW TO MOUNT THE SAFETY CHAIN 2 ON THE POST BED MACHINE WITH SLANTED PEDESTRAL 1 : » The carrier of the safety chain 3 should have a distance of 195mm to the machine housing. (Picture 2) ATTENTION: The chain must hold the machine securely when the machine is tilted backwards. » If the machine is tilted back, the safety spring 4 must be locked securely. The distance bet- ween the table top and safety spring must be at least 5mm. (Picture 3)

01. PREFACE 07.02. SAFETY DEVICES FOR TILTING (SAFETY SPRING) HOW TO MOUNT THE SAFETY SPRING 1 : » Mount the safety spring 1 with the screws 2 . ATTENTION: The safety spring 1 must engage securely when the machine is tilted backwards. » If the machine is tilted back, the safety spring 1 should be locked securely. The distance bet- ween the table top and the bracket must be at least 5mm.

02. MACHINE DESCRIPTION 01. OVERVIEW OPERATING PANEL HOTKEYS CONTROL DONGLE PEDAL ELECTRONICS AND SEWING REVERSE

02. MACHINE DESCRIPTION 02. OPERATING PANEL The operating field indicates the current operating states. Operation takes place via continuous dialog between control and operator. Depending on the operating state, diferent texts are displayed. The following functions are assigned to the BUTTONS ABOVE AND BELOW THE DISPLAY: 1 BACKTACK (from left to right): A Start backtack B End backtack 2 THREAD TRIMMING 3 NEEDLE UP/DOWN AFTER STOP 4 LIGHT ON/OFF 5 PARAMETERS 6 NEW PROGRAM 7 PROGRAMMED SEAM 8 SAVE 9 CANCEL If a function is activated, this is indicated by illuminating the corresponding LED. In order to CHANGE OR SET VALUES, use the JOG KEY ( 10 ): Turning changes the values; pressing the JOG KEY enters the value. In the following, the operating type is indicated by the following icons: Input = Press the JOG KEY: Change = Turn the JOG KEY:

02. MACHINE DESCRIPTION 03. HOTKEYS 1 SAFETY SWITCH If the safety switch is triggered, all functions are locked. The LED lights up red. The “BLOCKED MODE” is active. NOTICE: Before activating the machine by the X-button make sure to remove sewing material or other items below the sewing feet if necessary and follow the instructions displayed in the control panel. 2 SINGLE BACKTACK SUPRESSION If the backtack function is activated, the following backtack is switched of once by pushing the key. 3 2ND STITCH LENGTH If the second stitch length is activated, the corresponding LED lights up. 4 CUSTOMIZABLE BUTTON Default: Toggle foot stroke level (see parameter M085)

NOTICE! The electronic handwheel is not active unless the machine has performed at least one stitch. For safety reasons it is necessary during “BLOCKED MODE” to push and hold the programmable button (the lowest button) 3 to activate the electronic handwheel. 1 ELECTRONIC HANDWHEEL – FUNCTION By turning the handwheel, you can move the needle bar up or down. From here on, the operating type is indicated by the following icons: Pressing the handwheel: stitch-for-stitch function / needle positioning Turning the handwheel: 2 REVERSE SEWING Pulling the button changes the sewing direction. 02. MACHINE DESCRIPTION 04. ELECTRONIC HANDWHEEL & REVERSE SEWING

1 MACHINE MAIN SWITCH Switches the machine ON / OFF 2 USB-PORT Identify yourself using the provided USB dongle. 02. MACHINE DESCRIPTION 05. CONTROL & MAIN SWITCH

02. MACHINE DESCRIPTION 06. PEDAL 0 IDLE POSITION +1 CONSTANT SEWING SPEED (adjustable via parameter M502) +2 VARIABLE SEWING SPEED FROM 0-100% OF THE CHOSEN MAXIMUM SPEED (depending on sewing program) -1 SEWING FEET LIFT -2 SEAM END PROCEDURE ACTIVATION (depending on sewing program)

02. MACHINE DESCRIPTION 07. LIGHT DISPLAY STEP DESCRIPTION » LIGHT ON/OFF The VETRON head module is equipped with LED lighting. Press the LIGHT button The corresponding LED on the display lights up. » ADJUST LIGHT INTENSITY 01 Press the LIGHT button The correspoding LED lights up on the display. 02 1 A 0 J I S H 0 D L U G T T Change LIGHT INTENSITY Percentage on the display and light intensity of the light are changed. 03 A J I S H D L U G T T 0 0 6 After 2 seconds without further input, the value is set and the current program number is shown. 04 P 2 2 W 4 1 3 3 1 5 P M O N R M R G A A E Machine is ready for operation

02. MACHINE DESCRIPTION 08. MACHINE START Press the main switch at the control box to turn on the machine. 01. Wait a few seconds until the machine is initialized. NOTICE! Make sure that no sewing material or other items are below the sewing feet before pushing the pedal. 02. Push the pedal. The sewing feet move and are finally positioned positioning on the needle plate. The red and white control lights 1 at the machine head are flashing during automatic movement. 03. The sewing light is automatically switched on. 04. The machine is now ready for use.

02. MACHINE DESCRIPTION 09. PROGRAM CHANGE NOTICE! Inside the seam it is not possible to change the program. Press the pedal back to thread trimming position to activate the function if necessary. 01. Push the JOG KEY 10 . 02. The current program number is flashing. 03. Turn the JOG KEY to the left or right to choose the desired program number. 04. Confirm your choice by pushing the JOG KEY again. 05. The machine is now ready for use.

02. MACHINE DESCRIPTION 10. DIRECT ACCESS NOTICE! It is possible to create operator´s direct access to one program parameter via the control panel. The direct access parameter is permanently shown in the display. The manipulations by the operator are not saved in the program and will be reset after program change or when the machine is turned of. By turning the JOG KEY 10 the value can be adjusted directly. The following parameters can be displayed: » OFF » Thread tension » Stitch length » Maximum speed » Top feed stroke » Top feed pressure » Bobbin thread counter (only display) » Edge guide distance » Current sewing speed (only display) » Current needle position in degrees (only display).

03. OPERATION OF THE MACHINE 01. INSERTING THE NEEDLE (1- NEEDLE) -1-2 CAUTION! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“ or turn the machine of, before inserting the needle. Failure to comply produces a risk of injury in case of an unintentional machine operation. INFO Only use needles from the system intended for the machine. (Needle system 134-35) 01. Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE”, or turn the machine of. 02. Loosen the screw 1 . 03. Push the needle 2 fully in until it stop. Make sure that the groove 3 on the needle is to the right side. 04. Tighten the screw 1 again. 05. Push the X-button or switch the machine on again and follow the instructions displayed in the control panel. NOTICE: Before activating the machine by the X-button make sure to remove sewing material or other items below the sewing feet if necessary and follow the instructions displayed on the control panel.

03. OPERATION OF THE MACHINE 01.01. INSERTING THE NEEDLE (2- NEEDLE) -2-2 CAUTION! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“, or turn the machine of before inserting the needles. Failure to comply produces a risk of injury in case of an unintentional machine operation. INFO Only use needles from the system intended for the machine. (Needle system 134-35) 01. Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE”, or turn the machine of. 02. Loosen the screws 1 . 03. Push the needles 2 fully in until they stop. Make sure that the groove 3 of the right needle points to the right and the left needle to the left. 04. Tighten the screws 1 again. 05. Push the X-button or switch the machine on again and follow the instructions displayed on the control panel. NOTICE: Before activating the machine by the X-button make sure to remove sewing material or other items below the sewing feet if necessary and follow the instructions displayed on the control panel.

03. OPERATION OF THE MACHINE 02. SEWING FEET EXCHANGE CAUTION! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“, or turn the machine of before you change the sewing feet. Failure to comply produces a risk of injury in case of an unintentional machine operation. During „BLOCKED MODE“ the sewing feet have no pressure or position control. They can be moved by the following method: 01. Press and hold the programmable button on the machine head (lowest button). 02. By turning the JOG KEY the sewing feet can be moved. 03. By loosening screws 1 the sewing feet can be exchanged. NOTICE! Push the X-button or switch the machine on again and follow the instructions displayed on the control panel.

CAUTION! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active“BLOCKED MODE“, or turn the machine of. Failure to comply produces a risk of injury in case of an unintentional machine operation. Make sure that the thread takeup lever 1 is in its top dead position. Now you can thread the machine according to the picture. NOTICE! Push the X-button or switch the machine on again and follow the instructions displayed on the control panel. 03. OPERATION OF THE MACHINE 03. THREADING THE MACHINE (1- / 2- NEEDLE)

03. OPERATION OF THE MACHINE 04. EXCHANGING THE BOBBIN AND ADJUSTING THE BOBBIN THREAD TENSION (1- / 2- NEEDLE) CAUTION! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“, or turn the machine of before removing the bobbin. Failure to comply produces a risk of injury in case of an unintentional machine operation. If the machine is equipped with the special feature “BOBBIN COVER DETECTION” it automatically enters the “BLOCKED MODE” after opening the bobbin cover. 01. Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE”, or turn the machine of. 02. Open the hook cover. Fold up the tab 1 and remove the bobbin 2 . 03. Insert the filled bobbin. Check the correct direction by pulling the thread end and assuring the rotation of the bobbin is counter-clockwise. 04. Pass the bobbin thread through the slot 3 , then pass the tension spring below and pull it out of the thread guide 5 . Close the tab 1 and the hook cover. 05. The bobbin thread tension can be adjusted at screw 4 . NOTICE! Push the X-button or switch the machine on again and follow the instructions displayed on the control panel.

03. OPERATION OF THE MACHINE 05. WINDING THE BOBBIN THREAD CAUTION! Avoid touching rotating parts to avoid the risk of injury or damage of the machine. 01. Turn the machine on. 02. Place a bobbin 1 on the bobbin winder 2 . 03. Push the lever 3 towards the bobbin. 04. After the winding process is finished, the lever 3 automatically moves back. 05. Remove the bobbin and cut the thread at the knife 4 . 06. Loosen the screw 5 and move the lever 3 to adjust the amount of thread on the bobbbin. There should be a gap of 1 mm between thread and bobbin edge. NOTICE! If necessary, the bracket 6 can be slightly bended to the left or right to optimize the thread flow to the bobbin.

03. OPERATION OF THE MACHINE 06. ENGAGING THE SAFETY CLUTCH DANGER! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“, or turn the machine of. Failure to comply produces a risk of injury in case of an unintentional machine operation. The safety clutch is integrated in the main drive module to protect the hook from damage. Causes of damage could be for example thread jamming, needle breakage or incorrect operation. If the safety clutch has released, perform the following procedure: 01. Turn the machine of at the main switch. 02. Remove the cause of the disorder. 03. Tilt the machine to the back, open the right cover to get access to the mechanical handwheel. 04. Take the 3 mm allen key of the accessories and stick it in screw 1 . Turn the handwheel until the key is touching the machine housing (picture left). 05. Take the 5 mm allen key of the accessories and put it in the handwheel gap (picture right). Turn the handwheel until the safety clutch is noticeably engaging. 06. Check the needle bar rise. (refer to chapter 03.12. of the adjustment manual). If confirmed, the machine is ready for use again. NOTICE! Push the X-button or switch on the machine again and follow the instructions displayed on the control panel.

03. OPERATION OF THE MACHINE 07. SAFETY SPRING 4 ZONE BETWEEN MACHINE AND TABLE NOTICE: By tilting the machine back, the safety spring 5 hooks on the table. The machine can not tilt forward. How to unlatch the safety spring 5 : 01. Push the machine slightly backward. 02. Press safety spring 5 carefully in direction of arrow. 03. Under consideration that nothing is between machine and table 4 , the machine can now be tilted forward. 04. The machine is ready for use again. CRUSHING Crushing and bruising can occur, when the machine is moved to the operating position, between the machine and the table 4 . 5 SAFETY SPRING

04. MAINTENANCE 01. MAINTENANCE INTERVALS ADVICE! In the following chapter we will introduce you to the most important mainte- nance areas to be checked daily & before each use. Detailed maintenance and cleaning instructions can be found in the respective adjustment instruc- tions in chapter 05.

04. MAINTENANCE 02. OIL LEVEL CHECK Check the oil level before starting! NOTICE: The handling and disposal of mineral oils is subject to legal regulation. Deliver used oil to an authorized collection point. Protect your enviornment. Take care not to spill oil. INFO! By tilting the machine during power on, a gravity sensor automatically switches the machine into “BLOCKED MODE”. This is noted on the display. 01. Tilt the machine to the back. The oil tank is located below the base plate. 02. If necessary, slightly pull the oil plug 1 and fill the tank up to the “max” marking. 03. Please use only oil types recommended by VETRON. E.g.: Oil PP 20 DAB 10 (Viscosity 40° C: 15 mm2/s; Flashpoint: 150°) (Can be ordered under the number: SuS 6436) WARNING! Oil on the skin, or swallowed. If you get oil on your skin, make sure you clean it of the skin thoroughly. In case you should swallow the oil seek medical attention immediately. Or call the service hotline: +49 631 / 2014 - 460 Minimum Maximum WARNING! Before all maintenance work: push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“, or turn the machine of. Failure to comply produces a risk of injury in case of an unintentional machine operation.

04. MAINTENANCE 03. CLEANING THE MACHINE CAUTION! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“, or turn the machine of before cleaning the hook area. Failure to comply produces a risk of injury in case of an unintentional machine operation. PLACES IN SPECIAL NEED OF CLEANING: » area under the stitch plate 1 » area around the the hook 2 » bobbin housing » feeders » thread trimmer » needle area Clean the hook area daily. With increased lint depending on materials, clean the hook area several times a day. For more cleaning tilt the machine back and clean the guard tank. NOTICE! If you tilt the machine during power on, a gravity sensor automatically switches the machine into “BLOCKED MODE”. This is noted on the display.

CAUTION! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“, or turn the machine of before checking the timing belts. Failure to comply produces a risk of injury in case of an unintentional machine operation. SEWING DRIVE: » Clean fan grill 3 from the main drive (e.g. with an air blow gun). » Tilt the machine in order to check the condition of the timing-belts 4 and 5 . The timing belts can be reached easily in this position. NOTICE! If you tilt the machine during power on, a gravity sensor automatically switches the machine into “BLOCKED MODE”. This is noted on the display. 04. MAINTENANCE 04. SEWING DRIVE

04. MAINTENANCE 05. PNEUMATIC SYSTEM CAUTION! RISK OF INJURY! Push the X-button at the machine head, the red light illuminates showing the active “BLOCKED MODE“, or turn the machine of before checking the pneumatic system. Failure to comply produces a risk of injury in case of an unintentional machine operation. CHECKING THE MAINTENANCE UNIT: Check water in pressure regulator: » The water level should not rise to the level of the filter cartridge 6 . After unscrewing the drain screw 8 , the water will flow under pressure out of the water sepera- tor 7 . Clean filter cartridge: » Dirt and condensation are seperated through the filter cartridge 6 . » Disconnect the machine from the compressed air supply. » Loosen the drain screw 8 . There should not be any pressure in the machine pneumatic system. » Unscrew the water seperator 7 . » Unscrew the filter cartridge 6 . Wash the filter shell and cartridge with cleaning fluid (no solvent) and blast clean. » Re-assemble the maintenance unit. Check for system leaks.

05. PROGRAMMING 01. GENERAL Basically The adjustments for e.g. stitch length, thread tension, foot pres- sure and other settings are made with equipment like knobs, switches and dials on conventional sewing machines. These settings are not accurately reproducible after changing them. With the VETRON, these settings are made by step motors, they can exactly reproduce the desired setting. All settings for e.g. stitch length, thread tension and foot pressure are adjusted with parameters on the controller. Single- and Chainprograms A complete setting of the machine is called a program and can be stored under a name or a number. A change of progam can be done with the push of a button and all adjustments are carried out. Multiple settings of diferent machines can be united in one machine. It is also possible to concatenate several programs. They will run automatically one after another. This is called a chain program. A progam can be used as a single program, or be linked in a chain program. Changes in a program will be active in a chain program. For this reason it is advisable to store the parts of a chain progam separately e.g. with a number higher than 50 upwards. Measurement of the material thickness The machine is fitted with a electronic device 1 that can regis- ter the thickness of the material. This device enables the machi- ne to react independently to diferent requirements within one seam, depending on the configuration. The thread tension, foot pressure and stitch length are adjusted with increasing material thickness. Notice when switching on machine The system will calibrate itself every time you switch the machi- ne on. Also after pushing the safety switch (X-Key) calibration will take place. Calibration must take place without material un- der the sewing foot. The needle plate surface is 0mm material thickness.

05. PROGRAMMING 02. CREATE PROGRAMNAME AND STORING DISPLAY STEP DESCRIPTION » CREATE PROGRAM NAME AND STORING 1 Push the key NEW PROGRAM ( 6 ) ► 2 P 0 ) 0 3 C E R A T G R P A O M E R The next empty program space will be shown on the display. 3 ► Push the JOG KEY (10) 4 E P T G M R N N R E E A Program name or number can be entered on the display. 5 ► Push the JOG KEY again 6 A E P T G M R N N R E E A The cursor on the display will flash. You can select a number or letter by turning the JOG KEY. Push the JOG KEY to confirm selection. The cursor will move to the position for the next number or letter. You can enter a maxi- mum of 15 digits. 7 V T O ) E 1 R N E P T G M R N N R E E A Move the cursor below the righthand arrow when the name is complete. 8 P 0 0 1 V T O E R N ► Push the JOG KEY to confirm your entry. The display will now show your selected name. ADVICE! Turn the JOG KEY to select the desired parameter. Push the JOG KEY. The parameter will flash and can be changed by turning the JOG KEY. Pushing the JOG KEY again will store your input.

05. PROGRAMMING 03. CHANGE PROGRAM NAME DISPLAY STEP DESCRIPTION » CHANGE PROGRAM NAME 1 Push the P button ( 5 ). ► The appropriate LED will shine on the display. 2 0 T 1 O V 0 R N E 1 P m o a r e r n g m a Parameter 1 appears on the display. Now you can change the name. 3 ► Turn the JOG KEY to the right. You are directed to the program parameters.

05. PROGRAMMING 04. PROGRAM PARAMETER -1-10 NR. PARAMETER DESCRIPTION » STITCH LENGHT IN THE SEAM 010 Stitch length 1 Main stitch length in mm in the seam. The stitch length can also be entered in the negative range. The seam will be done in reverse. 011 Stitch length 2 Second stitch length, which can be selected by pushing button 4 (parameter 018). The stitch length can also be entered in the negative range. The seam will be done in reverse. 018 Button 4 Stitch length trigger function Select function with button 4 . OFF Without function SWITCH Stitch length will change to 2nd stitch length as long as you hold it. When button is released 1st stitch length is back. TOGGLE Stitch length will change when button is pressed. When it is pressed a second time, it will change back to 1st stitch length. NR. PARAMETER DESCRIPTION » FOOT STROKE 020 Foot stroke 1 Stroke in mm during normal sewing. The value must be set depending on the thickness and texture of the material to achieve a correct material feed. 021 Foot stroke 2 2nd stroke in mm. Can be switched on when reaching thick joints in the seam. Switching over can be done with key 3 or the electronic handwheel 1 . It can also be done with a knee lever (optional) or with the automatic switch parameter 027. ADVICE: A seam program can be created with the following parameters. When a function is deactivated the according parameter will not be displayed. To select a progam parameter you have to turn the JOG KEY and push it when the desired parameter appears. It will now flash. Now you can select the desired parameter setting by turning the JOG KEY. The new setting will be stored by pushing the JOG KEY again.

05. PROGRAMMING 04. PROGRAM PARAMETER -2-14 NR. PARAMETER DESCRIPTION » FOOT STROKE 027 Automatic stroke switch The machine will switch over to a higher stroke automatically after a certain time and revolution speed. ADVICE! Automatic stroke switch parameter 027 The stroke on an alternate machine are normally changed by pressing a button or with a knee lever. The VETRON can do this also automatically with the foot pedal. By activating parameter 027 it will activate the facility. When the machine is run a certain time on the 1st step of the foot pedal it will automatically change to a higher stroke setting. When you sew faster than the 1st step the machine will return back to the lower stroke. The time and revolution is adjustable (parameter 028, 029). 028 Automatic stroke switch speed threshold Rotation per minute when switch should take place. 029 Automatic stroke switch delay Delay time until stroke switch will occur. Time STROKE SIGNAL Automatic stroke switch Speed ON OFF OFF 030 thread tension A 1 010 stitch length 1 020 foot stroke 1 041 speed 027 automatic stroke switch according to sewing speed 031 thread tension A 2 038 2nd tension level when switched to 2nd stroke 039 release tension on foot lift 150 thread trimming 153 trim stitch tension 158 trim stitches 159 trim stitch length 050 foot pressure 074 foot position on stop 077 needle position on stop 110 stitch in stitch 140 backtack or condensed stitches at seam end 120 backtack or condensed stitches at seam start 100 thread clamp 135 bobbin thread counter 021 foot stroke 2 121 A stitch count 122 B stitch count 123 A/B repetition 124 A stitch length 125 B stitch length 126 A/B speed 141 C stitch count 142 D stitch count 143 C/D repetition 144 C stitch length 145 D stitch length 146 C/D speed 028 automatic stroke switch speed threshold 029 automatic stroke switch delay 032 thread tension B 1 034 thread tension based on material thickness 070 foot lift height » SEWING PARAMETER 033 thread tension B 2 054 dynamic foot pressure 066 Edge guide hight 060 edge value

NR. PARAMETER DESCRIPTION » THREAD TENSION ADVICE! Thread tension The thread tension on conventional machines is adjusted with a spring. The reproduction of the desired thread tension is difcult. The VETRON sets the thread tension with a step motor. The task of the tension spring is taken over by a elastomer. A second thread tension on conventional machines needs an additional tension unit. The VETRON accomplish the 2nd thread tension by increasing the tension. 030 Thread tension A 1 Main thread tension in program. Setting range 0 to 100 %. 031 Thread tension A 2 Higher thread tension than the main program. Setting range 0 to 100 %. The connection with the higher thread tension can be done by pushing button 3 , or 1 or when the 2nd top feed stroke is activated. 032 Thread tension B 1 (Two needle machine) Main thread tension in program. Setting range 0 to 100 %. 033 Thread tension B 2 (Two needle machine) Higher thread tension than the main program. Setting range 0 to 100 %. The connection with the higher thread tension can be done by pushing button 3 , or 1 or when the 2nd top feed stroke is activated. 034 Thread tension level increase / decrease based on material thickness Two function are available. Function 1 = OFF (no change on diferent material thickness) Function 2 = % (lower percentage = less thread tension increase) (higher percentage = more thread tension increase) Automatic thread tension adjustment depends on material thickness The tension will be adjusted with the information received from the material thickness recognition. You can activate this function with the parameter 034. With a lower percentage the increase will be less than with a higher percentage. 05. PROGRAMMING 04. PROGRAM PARAMETER -3-14

05. PROGRAMMING 04. PROGRAM PARAMETER -4-14 NR. PARAMETER DESCRIPTION » MAXIMUM ROTATION SPEED 040 Speed mode You can chose between two versions: Function 1 = PEDAL Sewing speed will be regulated by the posititon of the pedal. Function 2 = CONSTANT Constant sewing speed as selected in parameter 041. Automatic tension adjustment when material thickness changes 70 60 50 40 30 20 10 mm Thread tension rise Thread tension in % Material thickness 2 mm 4 mm NR. PARAMETER DESCRIPTION » THREAD TENSION 038 2nd tension level when switched to 2nd stroke Two functions are available. Function 1 = OFF Thread tension will not change over. Function 2 = ON Thread tension will change over. 039 Release tension on foot lift Three functions are available. Function 1 = OFF (No tension release when foot is lifted) Function 2 = END (Tension release when thread is cut) Function 3 = ALWAYS (Tension release when foot is lifted) 030 thread tension A 1 041 speed 031 thread tension A 2 038 2nd tension level when switched to 2nd stroke 140 backtack or condensed stitches at seam end 141 C stitch count 142 D stitch count 143 C/D repetition 144 C stitch length 145 D stitch length 146 C/D speed 032 thread tension B 1 034 thread tension based on material thickness 033 thread tension B 2 054 dynamic foot pressure 010 stitch length 1 020 foot stroke 1 027 automatic stroke switch according to sewing speed 039 release tension on foot lift 150 thread trimming 153 trim stitch tension 158 trim stitches 159 trim stitch length 050 foot pressure 074 foot position on stop 077 needle position on stop 110 stitch in stitch 120 backtack or condensed stitches at seam start 100 thread clamp 135 bobbin thread counter 021 foot stroke 2 121 A stitch count 122 B stitch count 123 A/B repetition 124 A stitch length 125 B stitch length 126 A/B speed 028 automatic stroke switch speed threshold 029 automatic stroke switch delay 070 foot lift height » SEWING PARAMETER 066 Edge guide hight 060 edge value

05. PROGRAMMING 04. PROGRAM PARAMETER -5-14 NR. PARAMETER DESCRIPTION » FOOT PRESSURE CONTROL ADVICE! Automatic foot pressure control On conventional machines the foot pressure is generated by a spring and will be adjusted seldom. The VETRON also generates the foot pressure with a spring, but the spring is pre-stressed by a step motor with gear (parameter 050). In diferent programs can diferent foot pressure be applied. You have the choice between three operation modes (parameter 054). Operation mode: 1 = OFF Foot pressure is generated like on a conventional machine. Can be diferent depending on the program. 2 = CONSTANT The foot pressure will be constant on all material thicknesses. The material thickness recog- nition will make sure that the foot pressure control that you have a constant foot pressure. 3 = 1-100% The foot pressure will be increased with increased sewing speed. Low percentage will increase the pressure only weak. High percentage will increase the pressure stronger. ADVICE! When sewing operations are done where the foot pressure is used to keep the material in position (e.g. piping), it is advisable to use operation mode 1 (OFF). Operation mode 2 (CONSTANT) will lead to a negativ result. The material thickness recognition will prevent positioning the piping. 050 Foot pressure You can set the foot pressure for the program here. Comparable to a conventional machine. 054 Dynamic foot pressure The following functions are available: Function 1 = OFF Function 2 = CONST Function 3 = % NR. PARAMETER DESCRIPTION » MAXIMUM ROTATION SPEED 041 Maximum speed The maximum speed will be entered here. 042 Softstart stitch count Here the stitches are set which are required for a soft start.

05. PROGRAMMING 04. PROGRAM PARAMETER -6-14 Foot pressure in % 30% adjusted Speed Automatic foot pressure Operation mode 1-100% (Pressure increase over speed) 70 60 50 40 30 20 10 High percentage Low percentage Foot pressure in % 30% adjusted Material thickness X OFF = The foot pressure increases with the material thickness (as in a conventional machine) Operation mode OFF 70 60 50 40 30 20 10 in mm X 2 mm X X 4 mm Foot pressure in % 30% adjusted Material thickness 70 60 50 40 30 20 10 in mm X X 2 mm X 4 mm X Operation mode CONSTANT CONSTANT= The foot pressure is the same for each material thickness 110 stitch in stitch 120 backtack or condensed stitches at seam start 135 bobbin thread counter 121 A stitch count 122 B stitch count 123 A/B repetition 124 A stitch length 125 B stitch length 126 A/B speed 030 thread tension A 1 010 stitch length 1 020 foot stroke 1 041 speed 027 automatic stroke switch according to sewing speed 031 thread tension A 2 038 2nd tension level when switched to 2nd stroke 039 release tension on foot lift 150 thread trimming 153 trim stitch tension 158 trim stitches 159 trim stitch length 050 foot pressure 074 foot position on stop 077 needle position on stop 140 backtack or condensed stitches at seam end 100 thread clamp 021 foot stroke 2 141 C stitch count 142 D stitch count 143 C/D repetition 144 C stitch length 145 D stitch length 146 C/D speed 028 automatic stroke switch speed threshold 029 automatic stroke switch delay 032 thread tension B 1 034 thread tension based on material thickness 070 foot lift height » SEWING PARAMETER 033 thread tension B 2 054 dynamic foot pressure 066 Edge guide hight 060 edge value

NR. PARAMETER DESCRIPTION » TARGET STITCH FUNCTION 078 Target stitch position ADVICE! Parameter 078 can only be selected when the position of stitch placing is activated in parameter 085, 086 or 087. The position of the needle point above the material is set with this parameter. 05. PROGRAMMING 04. PROGRAM PARAMETER -7-14 NR. PARAMETER DESCRIPTION » PRESSER FOOT HEIGHT, PRESSER FOOT POSITION, NEEDLE POSITION 070 Foot lift height The setting for the desired hight of presser foot lift is entered here (in mm) for the program in question. 071 Foot lift maximum for operator You can restrict the maximum foot heigth (mm) for the operator here. 074 Foot position on stop Two positions are available (Pedal in 0-position): UP or DOWN. 075 Foot position on seam end Two positions are available (Pedal in 0-position): UP or DOWN. 077 Needle position on stop Two positions are available (Pedal in 0-position): POS1 or POS2. NR. PARAMETER DESCRIPTION » ELECTRONIC RULER FOR EDGE DISTANCE (OPTIONAL) 060 Edge value Following functions are available: OFF = Edge ruler is deactivated. 0.1–35.0 mm = Edge ruler is activated (Edge distance e.g. 10 mm). The distance from the needle to the edge can be entered directly in mm. It can´t be set below the right edge of the presser foot. This setting can only be done by a service technican. 066 Edge guide height adjustment The setting for the desired height of the 2-axial edge guide is entered here in %. E

05. PROGRAMMING 04. PROGRAM PARAMETER -8-14 NR. PARAMETER DESCRIPTION » ALLOCATION OF HOTKEYS 080 Direct parameter access With this parameter you can select which functions will be shown on the display in the top right position. The value can be changed with the JOG KEY at any time. You can choose between: OFF = No access TENSION = Thread tension LENGTH = Stitch length SPEED = Sewing speed STROKE = Foot stroke PRESSURE = Foot pressure BOBBIN = Number of stitches remaining until bobbin thread is empty EDGE = Edge distance - ruler ASPEED = Actual speed is shown in the display NEEDLE P = Needle position COUNTER = Stitch count MULTIPLE 1 = Selectable: change program; stitch length; tension A 085 Key function (Key 3 ) With this parameter you can select the function for the key 3 in this program. You can choose between: OFF = No access TACKSW = In between tack for this program. (By pressing the key the machine will sew backwards as long as you hold it). TACKTG = In between tack for this program. (By pressing the key the machine will sew backwards. When pressing the key again it will sew forwards again). STROSW = Foot stroke for this progam. (By pressing the key you will switch to the 2nd stroke value. By releasing the key it will go back to the 1st stroke value). STROTG = Foot stroke for this program. (By pressing the key you will switch to the 2nd stroke. Pressing it again will change back to the 1st stroke). 074 foot position on stop 077 needle position on stop 110 stitch in stitch 120 backtack or condensed stitches at seam start 135 bobbin thread counter 121 A stitch count 122 B stitch count 123 A/B repetition 124 A stitch length 125 B stitch length 126 A/B speed 070 foot lift height 030 thread tension A 1 010 stitch length 1 020 foot stroke 1 041 speed 027 automatic stroke switch according to sewing speed 031 thread tension A 2 038 2nd tension level when switched to 2nd stroke 039 release tension on foot lift 150 thread trimming 153 trim stitch tension 158 trim stitches 159 trim stitch length 050 foot pressure 140 backtack or condensed stitches at seam end 100 thread clamp 021 foot stroke 2 141 C stitch count 142 D stitch count 143 C/D repetition 144 C stitch length 145 D stitch length 146 C/D speed 028 automatic stroke switch speed threshold 029 automatic stroke switch delay 032 thread tension B 1 034 thread tension based on material thickness » SEWING PARAMETER 033 thread tension B 2 054 dynamic foot pressure 066 Edge guide hight 060 edge value

05. PROGRAMMING 04. PROGRAM PARAMETER -9-14 NR. PARAMETER DESCRIPTION » ALLOCATION OF HOTKEYS 085 TENSSW = Thread tension switch from A1 to A2 for this program. (By pressing and holding the key you will switch to the 2nd tension as long as you hold the key. You will go back to the 1st tension setting by releasing the button) (also for two-needle machines B1and B2). TENSTG = Thread tension switch from A1 to A2 for this program. (By pressing the key you will switch to the 2nd tension. By pressing it again it will switch back to the 1st tension setting. (also for two-needle machines B1to B2). NEEDLE = By pressing the key the machine will switch to the 2nd needle position (needle up). By pressing it again it will switch back to the 1st position (needle down). TARGET = By pressing the key the machine will go to the target stitch posi- tion. Needle point just above the material. (Target stitch position parameter 078). SCENTER = For the machines with two-needles, this signal for seam middle guide can be switched of. TACKTYPE = With this function you can switch in the seam between stitch in stitch and normal back tack. POST BED = By pressing the key the post bed can be moved in or out. PULLER = By pressing the key the puller wheel can be moved up or down. 086 Handwheel function ( 1 ) Same functions as parameter 085, when the electronic handwheel is pushed 1 . 087 Knee switch function You have the same function as parameter 085, when the knee switch is pushed.

NR. PARAMETER DESCRIPTION » THREAD CLAMP 100 Thread clamp ( 5 ) The following functions are available: OFF = Out of action. ON = In action. The function of the thread clamp is equal to a thread wiper function. When the point of the hook catches the thread loop the clamp will close. The hook will pull the beginning of the thread down through the material. NR. PARAMETER DESCRIPTION » BACKTACK TYPE 110 Stitch in stitch backtack You can choose between: OFF = Out of action, normal backtack. ON = In action stitch, in stitch backtack. With a normal backtack the direction is changed while feeding. The penetration of the needle is not perfectly on top of each other. This is used for not visible seams. The stitches will be exactly in the same position with the stitch in stitch backtack. The feeding will be switched when the machine is standing still. It is used for visi- ble backtacks with high quality. 05. PROGRAMMING 04. PROGRAM PARAMETER -10-14 120 backtack or condensed stitches at seam start 135 bobbin thread counter 121 A stitch count 122 B stitch count 123 A/B repetition 124 A stitch length 125 B stitch length 126 A/B speed 030 thread tension A 1 010 stitch length 1 020 foot stroke 1 041 speed 027 automatic stroke switch according to sewing speed 031 thread tension A 2 038 2nd tension level when switched to 2nd stroke 039 release tension on foot lift 150 thread trimming 153 trim stitch tension 158 trim stitches 159 trim stitch length 050 foot pressure 074 foot position on stop 077 needle position on stop 110 stitch in stitch 140 backtack or condensed stitches at seam end 100 thread clamp 021 foot stroke 2 141 C stitch count 142 D stitch count 143 C/D repetition 144 C stitch length 145 D stitch length 146 C/D speed 028 automatic stroke switch speed threshold 029 automatic stroke switch delay 032 thread tension B 1 034 thread tension based on material thickness 070 foot lift height » SEWING PARAMETER 033 thread tension B 2 054 dynamic foot pressure 066 Edge guide hight 060 edge value

05. PROGRAMMING 04. PROGRAM PARAMETER -11-14 NR. PARAMETER DESCRIPTION » START BACKTACK 120 Backtack or condensed stitches at seam start You can choose between: OFF = No backtack at seam start. STCONDS = Condensed stitches at seam start. The distance A will be used for the condensed stitches. The stitch length will be set with parameter 124 (Distance B is suppressed). BACKTACK = Backtack with distance A and B. BACKTACK B = Backtack with distance A and B and A. Use/Advantage: for diferent backtack length to stitch length. 121 A stitch count Can be set from 0 to 100 stitches. 122 B stitch count Can be set from 0 to 100 stitches. 123 AB repetition Can be set from 0 to 100 stitches. Repeats the start backtack depending on adjustment. 124 A stitch length You can choose between: STD = Stitch length for A in backtack same as length set in parameter 010 (Main stitch length). 4.0 mm = Stitch length for A in backtack can be choosen irrespective of the main stitch length (parameter 010) (e.g. 4.0 mm). -4.0 mm = When the stitch length for A in backtack is entered in the minus range this part of the backtack will be done in reverse. 030 thread tension A 1 010 stitch length 1 020 foot stroke 1 041 speed 027 automatic stroke switch according to sewing speed 031 thread tension A 2 038 2nd tension level when switched to 2nd stroke 039 release tension on foot lift 150 thread trimming 153 trim stitch tension 158 trim stitches 159 trim stitch length 050 foot pressure 074 foot position on stop 077 needle position on stop 110 stitch in stitch 140 backtack or condensed stitches at seam end 120 backtack or condensed stitches at seam start 100 thread clamp 135 bobbin thread counter 021 foot stroke 2 121 A stitch count 122 B stitch count 123 A/B repetition 124 A stitch length 125 B stitch length 126 A/B speed 141 C stitch count 142 D stitch count 143 C/D repetition 144 C stitch length 145 D stitch length 146 C/D speed 028 automatic stroke switch speed threshold 029 automatic stroke switch delay 032 thread tension B 1 034 thread tension based on material thickness 070 foot lift height » SEWING PARAMETER 033 thread tension B 2 054 dynamic foot pressure 066 Edge guide hight 060 edge value

05. PROGRAMMING 04. PROGRAM PARAMETER -12-14 NR. PARAMETER DESCRIPTION » IN THE SEAM 130 Stitch counted seam track Free sewing, normal seam Free sewing, normal seam You can choose between: OFF = The seam is done manually. Free sewing, normal seam. 1 – 20.000 = Stitch counted seam. The seam will be ended automatically when the entered amount of stitches is done (e.g. 30 stitches). 135 Bobbin thread counter You can choose between: OFF = The bobbin thread counter is switched of. 50 – 20.000 = You can enter the amount of back counting stitches here (max. 20.000 stitches). INFO! The red LED in the safety switch (X Key) will flash when the entered amount of back counting stitches has been reached. The machine will continue work until the next thread cut. The machine is blocked after the thread cut and on the display you will see the request to change the bobbin. After changing the bobbin you have to press the safety switch (X Key) to reset the bobbin thread counter. NR. PARAMETER DESCRIPTION » START BACKTACK 125 B Stitch length You can choose between: STD = Stitch length for B in backtack same as length set in parameter 010 (main stitch length). 4.0 mm = Stitch length for B in backtack can be choosen irrespective of the main stitch length (parameter 010) (e.g. 4.0 mm). -4.0 mm = When the stitch length for B in backtack is entered in the minus range this part of the backtack will done in reverse. 126 AB Speed You can choose between: PEDAL = The speed for sewing the backtack will be regulated with the foot pedal. 800 S/min = You can select a speed of 50 – 2000 S/min.

05. PROGRAMMING 04. PROGRAM PARAMETER -13-14 NR. PARAMETER DESCRIPTION » END BACKTACK 140 Backtack or condensed stitches at seam end You can choose between: OFF = No tack on end of seam. STCONDS = Condendsed stitches at end of seam. The distance D will be used for the backtack. The stitch length will be set in parameter 145 (Distance C will be suppressed). BACKTACK = End backtack with distances C and D. 141 C Stitch count C Can be set between 0 and 100 stitches. 142 D Stitch count Can be set between 0 and 100 stitches. 143 CD repetition Can be set between 0 and 100 stitches. Repeats the complete backtack depending on setup. 144 C Stitch length C You can choose between: STD = Stitch length for B in backtack same as length set in parameter 010 (Main stitch length). 4.0 mm = Stitch length for B in backtack can be choosen irrespective of the main stitch length (parameter 010) (e.g. 4,0mm). -4.0 mm = When the stitch length for B in backtack is entered in the minus range this part of the backtack will done in reverse. 030 thread tension A 1 010 stitch length 1 020 foot stroke 1 066 Edge guide hight 060 edge value 041 speed 027 automatic stroke switch according to sewing speed 031 thread tension A 2 038 2nd tension level when switched to 2nd stroke 039 release tension on foot lift 150 thread trimming 153 trim stitch tension 158 trim stitches 159 trim stitch length 050 foot pressure 074 foot position on stop 077 needle position on stop 110 stitch in stitch 140 backtack or condensed stitches at seam end 120 backtack or condensed stitches at seam start 100 thread clamp 135 bobbin thread counter 021 foot stroke 2 121 A stitch count 122 B stitch count 123 A/B repetition 124 A stitch length 125 B stitch length 126 A/B speed 141 C stitch count 142 D stitch count 143 C/D repetition 144 C stitch length 145 D stitch length 146 C/D speed 028 automatic stroke switch speed threshold 029 automatic stroke switch delay 032 thread tension B 1 034 thread tension based on material thickness 070 foot lift height » SEWING PARAMETER 033 thread tension B 2 054 dynamic foot pressure

05. PROGRAMMING 04. PROGRAM PARAMETER -14-14 NR. PARAMETER DESCRIPTION » SEAM END 150 Thread trimming You can choose between: OFF = Thread trimmer is inactive. ON = Thread trimmer is active. 153 Trim stitch tension (Only for Sub Class -11) You can choose between: -1 = Thread tension by trimming 0-100% = Thread tension released Thread tension value 157 Reserved (Only for Sub Class -11) Thread trimming tension, adjustable: -2 = The same thread trimming tension as the sewing thread tension -1 = Released thread tension 0-100 = Thread trimming tension in % 158 Trim stitches Extra stitches before thread trimming, released by trimming. Adjustable between OFF and 100 stitches 159 Trim stitch length Stitch length setting for the setted trim stitch. 160 Backturn You can choose between: OFF = Backturn is inactive. ON = Backturn is active. NR. PARAMETER DESCRIPTION » CHAIN PROGRAM 999 Chain program This parameter will show if a progam is used in a chain program. INFO! A chain program can be used when diferent operations on a work piece are done one after the other. The machine will set itself automatically for the next work step. NR. PARAMETER DESCRIPTION » END BACKTACK 145 D Stitch lenght You can choose between: STD = Stitch length for B in backtack same as length set in parameter 010 (Main stitch length). 4.0 mm = Stitch length for B in backtack can be choosen irrespective of the main stitch length (parameter 010) (e.g. 4.0 mm). -4.0 mm = When the stitch length for B in backtack is entered in the minus range this part of the back tack will done in reverse. 146 CD speed 800 S/min = Can be set between 50 – 2000 S/min (e.g. 800 S/min)

seam situation inside seam seam end P001 P002 end seam situation stitch count » CHAIN PROGRAM switch over stitch counted pedal -2 key wheel key 05. PROGRAMMING 05. CREATE PROGRAM CHAIN -1-4 DISPLAY STEP DESCRIPTION » CREATE PROGRAM CHAIN 1 Press the CHAIN PROGRAM Key ( 7 ) ► 2 S - H ) 0 0 P C - 1 1 0 P m o n r e g a A sequence of progams will be shown on the display. 3 ► Turn the JOG KEY (10) to the right to select the 1st program. 4 ► Turn the JOG KEY (10) to store. 5 S T C D U T E O N S t i p c w y t e h You can chose on the display the way to switch over to the next program. The following selection of switch over are available (see next page below point 6): Stitch count = A certain amount of stitches for the seam sequence will be entered (e.g. 30 stitches). The machine stop after this work step is done. Bring the foot pedal in the centre position to switch to the next seam sequence. PEDAL -2 = The seam sequence is done manually. By bringing the foot pedal in position –2 at the end of the seam the sequence is ended and switches to the next work step. This can be done with thread trimming or “continue sewing” depending on the program. Program Key = The next work step is initiated by pressing the key 3 . (see next page) Electronic handwheel = The next work step is initiated by pressing the electronic handwheel 1 . (see next page) INFO! A chain program consist of several programs which a run one after the other. The switch to the next work step can be chosen diferently. It can be done e.g. after a stitch counted seam or by pressing a key. The next step can also be initiated by the thread cut or the PEDAL -2 position. A chain program will be shown by a diode above the chain program key.

05. PROGRAMMING 05. CREATE PROGRAM CHAIN -2-4 DISPLAY STEP DESCRIPTION » CREATE PROGRAM CHAIN 6 Seam 1 Seam 2 Stitch count PEDAL -2 Program Key Electronic handwheel 7 ► Turn the JOG KEY (10) to store. 8 I S E D M N S I A E S i a u o t e t m a n s i You can enter the postion in the seam for the switch over here. 9 You can choose between the following types of switch over: In the seam = Switch will occure before backtack and thread trimming e.g. if you want to join two pieces with a chain on a program with start and end backtack it will switch to the next sequence before the end backtack (picture 1). Backtack and thread trimming will be deactivated. The next sequence starts after the start backtack (picture 2). The start backtack is deactivated. Seam end = The switch will take place (if part of the program) after the end backtack and thread trimming (picture 3). The next seam starts with a backtack (picture 4) (if part of the program). Picture 1 Picture 3 Picture 2 Picture 4

DISPLAY STEP DESCRIPTION » CREATE PROGRAM CHAIN 10 ► Push the JOG KEY (10) to set your selection. 11 INFO! After setting all the diferent programs you have to select the chain program end on the last sequence of the program chain. 12 S H N - C E - D ) Select PROGRAM END. 13 ► Push the JOG KEY (10) to accept your selection. 14 O F F B b o e i n o c b u r n t You will see BOBBIN on the display. 15 You can choose between: OFF = No stitch count of remaining stitches. 4300 = Number of remainings stitches until bobbin thread is empty (see parameter 135). 16 ► Push the JOG KEY (10) to accept your selection. 17 P 0 ) 0 3 C E R A T G R P A O M E R Choose number for this program. 18 ► Push the JOG KEY (10) to accept your selection. 19 E P T G M R N N R E E A Enter program name or number on the display. 05. PROGRAMMING 05. CREATE PROGRAM CHAIN -3-4 seam situation inside seam seam end P001 P002 end seam situation stitch count » CHAIN PROGRAM switch over stitch counted pedal -2 key wheel key

05. PROGRAMMING 05. CREATE PROGRAM CHAIN -4-4 DISPLAY STEP DESCRIPTION » CREATE PROGRAM CHAIN 20 V T O ) E 1 R N E P T G M R N N R E E A When the complete name is entered, move the cursor below the right arrow. 21 ► Push the JOG KEY (10). 22 P 0 ) 0 3 0 V / T 3 O 1 E 0 R N The program name and number for the chain program appear on the display and can be used now. Summary chain program: 1 PROGRAMM 2 SEAM START 3 SEAM 4 SWITCH OVER OPTION 5 END OF SEAM Up to 10 chain links

05. PROGRAMMING 06. PROGRAM ADMINISTRATION WITHOUT USB DONGLE -1-2 DISPLAY STEP DESCRIPTION » PROGRAM ADMINISTRATION WITHOUT USB DONGLE 1 Push the PARAMETER key ( 5 ): » The associated LED on the display shines. 2 0 T 1 O V 0 R N E F P Z O M R R A R E G A A ► go to the PROGRAM ADMINISTRATION. Turn the JOG KEY to the left! 3 e a a m r n g M a a D t anagem n e t The LED PARAMETER shines. 4 ► Push the JOG KEY (10). YOU CAN CHOOSE BETWEEN: A S C n p r a l g i o p g y o m e r B S D n l r a l t g i e p g e o m e e r C A D o l l r p t m l e g e a r e s A COPY PROGRAM 5A S C n p r a l g i o p g y o m e r ► Push the JOG KEY (10). 6A P 0 0 1 V T O E R N ► Turn the JOG KEY (10) to the program you want to copy. ► Push the JOG KEY (10). DEFAULT SETTING: The current program will be displayed. If you want to copy a diferent program, turn the JOG KEY. 7A P 0 ) 0 3 C E R A T G R P A O M E R ► Push the JOG KEY (10). The next free program space will be shown on the display. 8A E P T G M R N N R E E A ) - ► Push the JOG KEY (10). Program name or number can be entered. 9A A E P T G M R N N R E E A ) - ► Turn the JOG KEY (10) to select a letter or number. ► Push the JOG KEY (10) to jump to the next free space. Up to 15 letters or numbers can be entered.

05. PROGRAMMING 06. PROGRAM ADMINISTRATION WITHOUT USB DONGLE -2-2 DISPLAY STEP DESCRIPTION » PROGRAM ADMINISTRATION WITHOUT USB DONGLE 10A V T O ) E 1 R N E P T G M R N N R E E A - Move the cursor below the right arrow, after entering the complete name or number. ► Push the JOG KEY (10). S C n p r a l g i o p g y o m e r COPY PROGRAM will appear on the display. B DELETE ONE PROGAM 5B S D n l r a l t g i e p g e o m e e r ► Push the JOG KEY (10). 6B P 0 0 1 V T O E R N ► Turn the JOG KEY (10) to select the program to be deleted. ► Push the JOG KEY (10). DEFAULT SETTING: The current program will be displayed. If you want to delete a diferent program, turn the JOG KEY. 7B Y S N E / O D l t e e e -- ► Turn the JOG KEY (10) to select YES or NO. ► Push the JOG KEY (10) to confirm your selection. S C n p r a l g i o p g y o m e r The display will show COPY PROGRAM. C DELETE ALL PROGRAMS 5C A D o l l r p t m l e g e a r e s ► Push the JOG KEY (10). 6C Y S N E / O D l t e e e -- ► Turn the JOG KEY (10) to select YES or NO. ► Push the JOG KEY (10) to confirm selection. S C n p r a l g i o p g y o m e r The display will show COPY PROGRAM.

05. PROGRAMMING 07. PROGRAM ADMINISTRATION WITH USB DONGLE -1-5 DISPLAY STEP DESCRIPTION » PROGRAM ADMINISTRATION WITH USB DONGLE 1 Switch the machine on and insert the USB dongle. 2 Push the PARAMETER key ( 5 ): » The LED on the display is on. 3 0 T 1 O V 0 R N E P m o n r m r g a a e ► Turn the JOG KEY (10) and select PROGRAM ADMINSTRATION. Turn the JOG KEY to the left. 4 e a a m r n g M a a D t anagem n e t The LED PARAMETER shines. 5 ► Push the JOG KEY (10). YOU CAN CHOOSE BETWEEN THE FOLLOWING 9 OPTIONS: A S C n p r a l g i o p g y o m e r B S n r a l g i p g o m e r M e c i - S a h - U n > B C S n r a l g i p g o m e r U > B h - a n S M i - c e D S D n l r a l t g i e p g e o m e e r E A M o e l c r p i m - S l a g h a - U r n s > B F A U o > l B r h p - m a n l S g a M i r - s c e G A D o l l r p t m l e g e a r e s H C M u e n c a n i i i - S o a r f h t - U g n o > B I C u n a n i i o r f t g o U > B h - a n S M i - c e A COPY ONE PROGRAM 6A S C n p r a l g i o p g y o m e r ► Push the JOG KEY (10). INFO! Once the dongle is inserted into the USB-Port, a file with the serial number of the machine will be opend automatically. In this way you can transfer program from one machine to another. Serial number and program can be selected and transfered to the appropriate machine. Please use only VETRON USB Dongles to secure a safe transfer of data.

05. PROGRAMMING 07. PROGRAM ADMINISTRATION WITH USB DONGLE -2-5 DISPLAY STEP DESCRIPTION » PROGRAM ADMINISTRATION WITH USB DONGLE 7A P 0 0 1 V T O E R N ► Turn the JOG KEY (10) to the program you want to copy. ► Push the JOG KEY (10). DEFAULT SETTING: The current program will be displayed. If you want to copy a diferent program, turn the JOG KEY. 8A P 0 ) 0 3 C E R A T G R P A O M E R ► Push the JOG KEY (10). The next free program space will be shown on the display. 9A E P T G M R N N R E E A ) - ► Push the JOG KEY (10). Program name or number can be entered. 10A A E P T G M R N N R E E A ) - ► Turn the JOG KEY (10) to select a letter or number. ► Push the JOG KEY (10) to jump to next free space. Up to 15 letters or numbers can be entered. 11A V T O ) E 1 R N E P T G M R N N R E E A - Move the cursor below the right arrow when you finished entering the name or number. ► Push the JOG KEY (10). S C n p r a l g i o p g y o m e r COPY PROGRAM will appear on the display. B COPY ONE PROGRAM FROM MACHINE TO USB 6B S n r a l g i p g o m e r M e c i - S a h - U n > B ► Push the JOG KEY (10). 7B P 0 0 1 V T O E R N ► Turn the JOG KEY (10) to select the desired program. ► Push the JOG KEY (10). 8B S n r a l g i p g o m e r M e c i - S a h - U n > B Display will show SINGLE PROGRAM MACHINE ---> USB. C COPY ONE PROGRAM FROM USB TO MACHINE 6C S n r a l g i p g o m e r U > B h - a n S M i - c e ► Push the JOG KEY (10). 7C ( S A L H N R E C . I N M E 0 3 0 0 1 M ) Your machine number will be shown in brackets on the display. 8C ) S A L H ( N R E C . I N M E 0 1 4 1 8 M ► Turn the JOG KEY (10) to select the relevant machine. ► Push the JOG KEY (10). 9C U 0 B S 4 : 0 S R L G R E O . P N R ► Turn the JOG KEY (10) to select the desired program. ► Push the JOG KEY (10).

DISPLAY STEP DESCRIPTION » PROGRAM ADMINISTRATION WITH USB DONGLE 10C P 0 ) 0 3 C E R A T G R P A O M E R or P 0 0 5 O I E E W V T R R ► Turn the JOG KEY (10) to find a program space for your new program. ► Push the JOG KEY (10). You can use a new program place, or can overwrite a existing one. 11C V T O ) E 1 R N E P T G M R N N R E E A - ► If you want to change the program name, move the cursor by turning the JOG KEY (10) below the part you want to change. ► Push the JOG KEY (10) to make a change or to confirm it. 12C V T O ) E 1 R N E P T G M R N N R E E A - Move the cursor below the right arrow once you completed the name or number. ► Push the JOG KEY (10). D DELETE ONE PROGRAM 6D S D n l r a l t g i e p g e o m e e r ► Push the JOG KEY (10). 7D P 0 0 1 V T O E R N ► Turn the JOG KEY (10) to the program to be deleted. ► Push the JOG KEY (10). DEFAULT SETTING: The current program will be shown. If you want to delete another program, turn the JOG KEY. 8D Y S N E / O D l t e e e -- ► Turn the JOG KEY (10) to select YES or NO. ► Push the JOG KEY (10) to confirm your selection. S C n p r a l g i o p g y o m e r The display will show COPY PROGRAM. E COPY ALL PROGRAMS FROM MACHINE TO USB 6E A M o e l c r p i m - S l a g h a - U r n s > B ► Push the JOG KEY (10). 7E Y S N E / O O I E E W V T R R -- ► Turn the JOG KEY (10) to select YES or NO. ► Push the JOG KEY (10) to confirm your selection. F-1 COPY ALL PROGRAMS FROM USB TO MACHINE (AVAILABLE FOR VERSIONS 1.29 AND OLDER/LOWER) 6F A U o > l B r h p - m a n l S g a M i r - s c e ► Push the JOG KEY (10). 7F ( S A L H N R E C . I N M E 0 3 0 0 1 M ) Your machine number will be shown on the display in brackets. 05. PROGRAMMING 07. PROGRAM ADMINISTRATION WITH USB DONGLE -3-5

DISPLAY STEP DESCRIPTION » PROGRAM ADMINISTRATION WITH USB DONGLE 8F ) S A L H ( N R E C . I N M E 0 1 4 1 8 M ► Turn the JOG KEY (10) to select desired machine. ► Push the JOG KEY (10). 9F Y S N E / O O I E E W V T R R -- ► Turn the JOG KEY (10) to select YES or NO. ► Push the JOG KEY (10) to confirm your selection. F-2 NOTICE! The following has changed COPY ALL PROGRAMS FROM USB TO MACHINE (AVAILABLE FOR VERSIONS 1.30 AND UP) 7F Copy all sewing programs from the desired sewing machine (for example with serial number 1667) to a USB dongle. 8F Insert the USB dongle into the appropriate sewing machine (for example with machine number 1399).  USB recognizes machine and automatically creates a folder 1399 on the USB dongle. 9F Plug the USB dongle into a computer: All data (sewing programs) from the sewing machine folder (serial number 1667) on the USB dongle must be copied to the new folder of the sewing machine (serial number 1399). 10F Now all newly copied sewing programs can be copied from the USB dongle to the corresponding sewing machine (serial number 1399). NOTE: For reasons of technical feasibility, the procedure „Copy all programs from USB dongle to machine“ as of software version 1.30 and up, must be carried out in this way. G DELETE ALL PROGRAMS 6G A D o l l r p t m l e g e a r e s ► Push the JOG KEY (10). 7G Y S N E / O D l t e e e -- ► Turn the JOG KEY (10) to select YES or NO. ► Push the JOG KEY (10) to confirm your selection. A D o l l r p t m l e g e a r e s Display will show DELETE ALL PROGRAMS. H ADJUSTMENTS FROM MACHINE TO USB ADVICE! All the basic parameter settings can be stored on the USB-dongle. The original settings can be re-established fast after repair work or exchange of parts. 6H C M u e n c a n i i i - S o a r f h t - U g n o > B ► Push the JOG KEY (10). All data will be transferred to the USB dongle. 05. PROGRAMMING 07. PROGRAM ADMINISTRATION WITH USB DONGLE -4-5

DISPLAY STEP DESCRIPTION » PROGRAM ADMINISTRATION WITH USB DONGLE 7H Y S N E / O O I E E W V T R R -- ► Turn the JOG KEY (10) to select YES or NO. ► Push the JOG KEY (10) to confirm your selection. I ADJUSTMENTS FROM USB TO MACHINE 6I C u n a n i i o r f t g o U > B h - a n S M i - c e ► Push the JOG KEY (10). All data will be tranfered to the machine. 7I P s o n . e . r i c g s . P E A S T L W A I E NEVER remove the USB dongle while data is being transferred. C u n a n i i o r f t g o U > B h - a n S M i - c e Display will show CONFIGURATION USB ---> MACHINE. 05. PROGRAMMING 07. PROGRAM ADMINISTRATION WITH USB DONGLE -5-5

Program updates are available for download on our website under www.vetrontypical.com. Copy the current software update onto your USB dongle and proceed as follows: DISPLAY STEP DESCRIPTION » UPDATE THE OPERATING PROGRAM 1 Insert your DONGLE, with the current status, into the USB port. ADVICE Machine must be turned of! 2 Turn the machine on and press the JOG KEY a second later. 3 I l i s . i n . n i t i . a g » Confirm. 4 T B l p s E p c c r y a i i u e a o T B l p s E p c c r y a i i u a a a o Press the “PARAMETER” button: » 5 P P M S O O I 1 R R G 0 5 R R M S G G N 1 / A E Appears. Machine automatically updates the 5 steps. 1/5: Update 1of 5 6 P V M O R I K 5 R F G 5 R E M O G I N / A Y Update completed. 7 U P d e u e s t t s c o p l s r a a c b s ! e e e o Appears. 8 Turn machine of! 9 Turn machine on again. Now the machine with the new update can be operated on. E N e r 0 i r y 8 f r o 2 o t 0 n : p o INFO: If there is no information on DONGLE, „Error“ appears! 05. PROGRAMMING 08. UPDATE THE OPERATING PROGRAM

At the time of printing, all information and illustrations in this document were up-to-date. Technical changes without prior notice! NOTE! » Please remember that we are not liable for spare parts and accessories not purchased from us. These parts were neither examined by us, nor released. Consequently, the installation or use of these products can have a negative influence on features and your workflow of the machine. » We accept no liability for any damage caused by the use of non-original parts. » This Wear Parts List shows the main parts from the machine. A detailed list for the complete ma- chine is available on our website www.vetrontypical.com or can also be ordered as a manual. 06. WEAR PARTS 01. GENERAL INFORMATION

nickel plated DIN 912 - M4x10 nickel plated DIN 7984 - M4x12 nickel plated (2x) DIN 912 - M4x8 nickel plated Needle- System 134-35 559 1113 13 (2x) C144588201 (C) C144588301 (B) 559 0296 16 Tension Spring 559 0471 16 Tension Spring 134-35 559 1855 10 559 1856 10 559 3001 09 S150201003 559 3002 13 93WF5-002 17WF5-037 93WF5-014 DIN 913 - M3x2,5 DIN 912 - M3x8 179WF5-001 DIN 913 M3x3 (2x) 70 07/2020 VETRON 5300 - POST BED MACHINE - INSTRUCTION BOOK 06. WEAR PARTS 02.01. LISTING

559 1116 10 ISO 7380 M4x10 ISO 2009 M3x8 ISO 2009 M3x5 559 1131 10 559 0960 09 559 0274 10 DIN 84 M2x5 559 3242 10 (26mm) DIN 912 M3x6 559 2679 10 DIN 913 M6x8 DIN 912 M3x6 DIN 913 M6x8 559 3233 10 559 3234 10 559 3226 10 559 3235 11 71 07/2020 VETRON 5300 - POST BED MACHINE - INSTRUCTION BOOK 06. WEAR PARTS 02.02. LISTING

07. WIRING DIAGRAM 01. VETRON 8340 CONTROL BOX

07. WIRING DIAGRAM 02. POWER CONNECTION BLOCK DIAGRAM

07. WIRING DIAGRAM 03. 8640 STEPPER DRIVER TERMINAL

07. WIRING DIAGRAM 04. 8340 MAIN TERMINAL MAIN DRIVE

07. WIRING DIAGRAM 05. VETRON 5XXX HEAD PCB

07. WIRING DIAGRAM 06. VETRON 5XXX HEAD ADAPTER PCB

Clara-Immerwahr-Str. 6 67661 Kaiserslautern, Germany Tel.: +49 6301 320 75-0 Fax: +49 6301 320 75-11 [email protected] www.vetrontypical.com

Clara-Immerwahr-Str. 6 67661 Kaiserslautern, Germany Tel.: +49 6301 320 75-0 Fax: +49 6301 320 75-11 E-mail: [email protected] www.vetrontypical.com