Toro TX 1000 Operator's Manual

Solenoid Harness No Parts Required Procedure 1. Remove the 4 bolts and washers securing the manifold cover from the 4-in-1 bucket (Figure 25). g242611 Figure 25 1. Manifold cover 2. Bolt and washer (4) 2. Feed the solenoid connector end of the valve manifold solenoid harness down the outer protective sleeve of the 4-in-1 bucket hoses. 3. Remove the plugs from the valve manifold terminals and install the solenoid connectors as shown in Figure 26. g242609 Figure 26 1. Valve manifold 3. Valve manifold solenoid harness 2. Left and right solenoid connectors 4. Tighte ...

substantial slip-resistant footwear, and hearing protection during operation or while adjusting or repairing the machine. Tie back hair and do not wear loose jewelry. • After striking a foreign object, shut off the engine, remove the key, thoroughly inspect the attachment for any damage, and repair the damage before starting and operating the attachment. • Always lower the attachment each time you shut off the machine or leave the operating position. • Clean any dirt or debris that may hinder connecting the attachment to the ...

parking brake and lower the arms. 3. Shut off the engine, remove the key and allow the engine to cool. 4. Turn the battery-disconnect switch to the off position; refer to your machine Operator’s Manual. 5. If your machine does not have a battery-disconnect switch, disconnect the negative (black) cable from the battery, then disconnect the positive (red) cable (Figure 4). g029753 Figure 4 WARNING Incorrect battery cable routing could damage the machine and cables, causing sparks. Sparks can cause the battery gasses to explode, resulting in pe ...

substantial slip-resistant footwear, and hearing protection during operation or while adjusting or repairing the machine. Tie back hair and do not wear loose jewelry. • After striking a foreign object, shut off the engine, remove the key, thoroughly inspect the attachment for any damage, and repair the damage before starting and operating the attachment. • Always lower the attachment each time you shut off the machine or leave the operating position. • Clean any dirt or debris that may hinder connecting the attachment to the ...

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal136-5844 136-5844 1. Press the joystick switch left to open the bucket jaws. 3. Lock the accessory into Forward. 2. Press the joystick switch right to close the bucket jaws. decal100-4648 100-4648 1. Warning; crushing of arm hazard; crushing of leg hazard—keep bystanders away from the machine. decalau117-1898 AU117-1898 1. Tipping hazard—read the Operator’s Manual; the maximum load is 408 kg ...

Solenoid Harness No Parts Required Procedure 1. Remove the 4 bolts and washers securing the manifold cover from the 4-in-1 bucket (Figure 25). g242611 Figure 25 1. Manifold cover 2. Bolt and washer (4) 2. Feed the solenoid connector end of the valve manifold solenoid harness down the outer protective sleeve of the 4-in-1 bucket hoses. 3. Remove the plugs from the valve manifold terminals and install the solenoid connectors as shown in Figure 26. g242609 Figure 26 1. Valve manifold 3. Valve manifold solenoid harness 2. Left and right solenoid connectors 4. Tighte ...

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal136-5844 136-5844 1. Press the joystick switch left to open the bucket jaws. 3. Lock the accessory into Forward. 2. Press the joystick switch right to close the bucket jaws. decal100-4648 100-4648 1. Warning; crushing of arm hazard; crushing of leg hazard—keep bystanders away from the machine. decalau117-1898 AU117-1898 1. Tipping hazard—read the Operator’s Manual; the maximum load is 408 kg ...

Procedure Description Qty. Use 1 No parts required – Prepare the machine. Connector mount bracket 1 7-pin connector 1 Bolt (5/32 inches) 2 Spacer 2 2 Nut (5/32 inches) 2 Install the connector and connector mount bracket. Relay and loader arm harness 1 Plug nut 1 Grommet Wire harness retainer 1 3 Screw 2 Connect the loader arm branch. Self-tapping screw 2 Relay 2 4 Fuse (5 A) 1 Connect the relay and power lead connectors. 5 No parts required – Remove the existing lever. 6 No parts required – Install the 4-in ...