Topgreener TGWF3K Installation Instructions

INSTALLATION INSTRUCTIONS Voltage .........................................................................................................120VAC, 60Hz Incandescent/ Halogen................................................................................................600W Dimmable LED and Dimmable CFL............................................................................150W Operating Temperature......................................................................................32°F-104°F This device is warranted to be free of material and workmanship defects for 1 year from the date of purchase. Original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Top Greener, Inc. Warranties from other Top Greener products may vary. This warranty is nontransferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Top Greener shall not be liable to the purchaser or end user customer of Top Greener products for direct, indirect, incidental, or consequential damages even if Top Greener has been advised of the possibility of such damages. Top Greener’s total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory. Model: TGWF3K 3-Way Add-on Switch This cannot be used as a standalone switch. Requires connection with TGWF500D or TGWF15S (not included). Neutral Wire Required. SPECIFICATIONS WIRING for TGWF3K AUXILIARY SWITCH PRODUCT NOTES The TGWF3K is a Remote Add-on Dimmer Switch that is designed for installation with the TGWF500D. Traditional dimmers only allows you to dim the lights from one location and turn the lights on/off from other locations. The TGWF3K's remarkable design allows you to have full dimming and on/off control of the lights from multiple locations. Follow the diagrams in this manual to connect the main dimmer (model TGWF500D or TGWF15S not included) and the add-on dimmers to multiple locations. WARRANTY WARNING Turn the POWER OFF at the circuit breaker before installing the Dimmer Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a qualified electrician performs this installation. Use copper wire only Use Wires with Minimum Temperature Rating 75°C (167°F) Common 3-Way wiring: 3-way switches are commonly wired as depicted below with the Power "LINE" entering the electrical wall box at one location, then connected to a second location with a 3 conductor (14-3 or 12-3 cable), and lastly connected to the light (or LOAD) by a 2 conductor (14-2 or 12-2 cable). This diagram is to be used only as a guide for what to expect when the existing switches are removed from the walls. TRAVELER 1 TRAVELER 2 HOT NEUTRAL GROUND LOAD SWITCH 1 SWITCH 2 LINE White (Neutral) Traveler(Yellow) Red (Load) TGWF3K TGWF500D Green (Ground) Black (Hot) New construction wiring: The diagram below shows the wiring for new constructions. This wiring method requires the LINE and LOAD wires to connect to the primary switch, TGWF500D or TGWF15S (not included). To connect the TGWF3K to a primary switch (TGWF500D or TGWF15S) using the existing wires in the wall, follow the wiring diagrams on the next page. FCC COMPLIANCE STATEMENT FCC Grant of Equipment Authorizations of this device and transmitters installed in this device can be found at FCC website by entering the FCC ID number on the device. Caution: Changes or modifications not expressly approved by the part responsible for compliance could void the user’s right to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

• To turn on the lights ON to the last used brightness level, press and release the top Dimmer Paddle • To brighten the lights, press and hold the top Dimmer Paddle and release when the desired level is reached • To dim the lights, press and hold the bottom Dimmer Paddle and release when the desired level is reached • To save the brightness level and turn off the lights, press and release the bottom Dimmer Paddle Air Gap Switch on the TGWF500D Dimmer Switch Paddle CHANGING THE FACE COVER To replace the face cover, use a flat screwdriver and insert the tip at the gap shown in the diagram above and pry cover off. To re-install, simply align the cover and snap back on. 3-Way Installation with TGWF3K Using existing wires: Follow this diagram to replace your existing 3-way switches. Be sure that the primary switch (TGWF500D or TGWF15S) is installed at the location with the HOT wire. Installation with Multiple TGWF3K Multiple locations: Follow this diagram to replace your existing 3-way and 4-way switches. The light (LOAD) may be installed at any location. The Air Gap Switch located below the Dimmer Switch Paddle is designed for your safety. With push buttons switches, it is difficult to know if the switch is in the On or the Off position without having to use a tester. This switch eliminates the hazard of having to change a light bulb on a possibly live fixture. Use the Air Gap Switch to Power Off before you change the bulb.