pardo QUEEN Assembly Instructions Manual

DIY WALL BED CABINET & MECHANISM No 2 & No 4 Phillips Head Screwdrivers Electric Drill (Hammer Drill for Masonry) Spirit Level Hammer Pliers Socket Set No 2 Slot Head Screwdriver 6.5mm Masonry Drill Bit Adjustable Spanner 26.02.13

(refer to detail) 340mm 240mm Board is to lean back against the wall Pillowcatch Head Board with 4 x holes Bolt thru back of pillowcatch so that the nut is on the inside of the mechanisim Mechanisim Piano Hinge Cupboard 1. 4. 3. 2. 5. 6. Panels (Queen) 1 x Top 1 x Top Back Rails 1 x Left Hand End 1 x Right Hand End 1 x Front Skirting 1 x Bottom Back Rail 4 x Door Panels 1 x Pillow Catch 1 x Head Board Panel # 1 2 3 4 5 6 7-10 11 12 Size (mm) 1655 x 464 1655 x 250 2227 x 480 2227 x 480 1655 x 150 1655 x 570 2108 x 419 1500 x 370 1500 x 270 9. 10. 8. 7. 1. 11. 12. Piano hinge Both edges to be cut at 17 degrees Detail Cabinet Components Pillowcatch DIAGRAM 1

* 60 x 25mm x 4 gauge csk screws for interfold hinges 26 x Cam Bolts 10 x Green Wall Plugs 26 x Cams 2 x Handles 6 x Interfold Hinge 2. 10 x Mounting Plates 10 x Clip on Hinge refer to detail 1 2 3 4 5 6 8 7 Mechanism Components Hardware 1. AUTOMATIC FOOT 2. BED FRAME 3. CONNECTING ROD 4. SPRING MECHANISMS 5. WALL MOUNTING BRACKETS 6. CRADLES 7. MATTRESS GUARD 8. EXTENSION ARM DIAGRAM 1

Left hand end Floor Front Skirting Bottom back rail Top back rail Top 1. 2. 4. 3. 6. 5. Step 1 - Cabinet Assembly NOTE: STEP 1. IS ONLY REQUIRED IF PURCHASING CABINET WITH BED MECHANISM * Place right hand end #4 on top of panels #1, #2, #5 and #6 ensuring all wooden dowel and cam bolts are inserted correctly. Tighten all cams. Refer to Diagram 3 * Lay left hand end #4 on floor with cam bolts upright. * Join shelf #2 to left hand end #4 and tighten cams. * Join top #1 to left hand end #4 and tighten cams. * Join top back rail #3 to left hand end #4, top #1 and shelf #2. Tighten cams. * Join bottom back rail #7 to left hand end #4 and tighten cams. * Join front skirting #6 to left hand and #4 and tighten cams Refer to Diagram 2 * Using hammer, tap cams into 20mm holes in all panels where required. * Screw cam bolts into 5mm holes in all panels where required. Hammer fix cam in place. Screw fix cam bolt into 5mm holes. 3. DIAGRAM 2 DIAGRAM 3

before pushing cabinet against the wall End Panel Front Panel DETAIL B Fastening with angle brackets DETAIL A Wall plugs Refer to detail B Refer to detail A Step 2 - Fixing Cabinet To Wall * Lay cabinet face down with bottom facing the wall. * To ensure the cabinet sits neatly against the wall when upright, it may be necessary to cut a larger recess into bottom of left and right hand end of cabinet to go over skirting. (refer to detail B) * Lift cabinet at top, pushing towards wall, being careful to have sufficient ceiling clearance. * Place cabinet into position against the wall and, using a spirit level against either the right or left hand end and the top, find the correct vertical and horizontal position. Mark this position on the wall with a pencil. PLEASE NOTE As there is a lot of tension in the Wallbed when in the open position, it is very important that the cabinet is securely fixed to the wall. IMPORTANT NOTE: Before moving cabinet upright, ensure all cams are tightened securely. * Locate wall studs and mark clearly with pencil. * Sit angle brackets in cabinet top, flush with top and back edge and against the wall studs. Ensure that the twin hole side of bracket is against the wall. * Fix angle brackets through wall into studs using 65mm screws provided. * Ensure cabinet is in correct vertical position. Fix bottom of brackets into cabinet top using 16mm screws. FASTENING OPTIONS 1 USING ANGLE BRACKETS (for gyprock, fibro or timber walls) FASTENING OPTIONS 2 * Ensure cabinet is in correct vertical position. * With a pencil or nail, mark the wall through the predrilled holes in the top back rail and the bottom back rail. * Move cabinet back into place against wall. * Fix top back rail to wall using 61mm screws. Put on cover caps. (for brick/masonry walls) * Move cabinet aside. Using a 6.5mm masonry bit, drill 60mm deep holes into wall and insert wall plugs supplied. * Fix bottom back rail to wall. Countersink screws to avoid pillow catch scraping on them. * Fix bottom back rail to wall. Countersink screws to avoid pillow catch scraping on them. 4.

Step 3 - DIY Mechanism Assembly / Instructions * Attach spring mechanisms (#4) to front and back cradle (#6) using small nuts and bolts provided. Ensure to attach the wall mounted brackets (#5) with the ends turned inwards together with the spring mechanism to the top rear bolt. (See diagram 4) * Fix the cradle assembly to the floor using the 75mm screws provided. 50mm green wall plugs are also provided if fixing to concrete floor. * Once the cradle is fixed to the floor, fix the wall mounted brackets (#5) to the wall using the 28mm screws provided. 50mm green wall plugs are also provided if fixing to concrete or brick walls. * Lower the bed frame in between the mechanism arms and bolt through the predrilled holes to the cradle assembly. You might find that the bed frame will be a tight fit in between the mechanism arms. (See diagram 4) * Remove the split pin and washer from the extension (#8) and attach the connecting rod (#3) to the extension through the predrilled hole on the connecting rod (#3) and replace the washer and then the spit pin. You might need to lower the bed frame slightly to line up the extension (#8) and the connecting rod (#3). . (See diagram 4) * Attach the red handle supplied to the Automatic foot (#1) using the screws provided. To avoid damage to the connecting rod, be sure that the bed is lowered using the red handle. NOTE: If fixing through a carpet floor, it is recommended that a small cut be made in the surrounding area to be drilled so that no threads are pulled in the carpet pile. Also if fixing to a timber floor, 2mm pilot holt is to be drilled in the floor before screwing through the cradle into the floor. NOTE: It is very important that the cradle is fixed back to the wall and floor securely as there will be substantial tension exerted on the cradle when the mechanism is in the lowered position. WARNING When operating the wall bed mechanism the bed frame must be carefully lowered all the way to the floor and NOT left to drop freely. If the bed frame is lowered without the weight of a mattress it may spring back causing injury. Do not try to vary the tension of the spring mechanism as it is NOT adjustable. DIAGRAM 4 Refer to Diagram 4 * If not using pillow catch, bolt on mattress guard(s) to the top of the bed frame through the predrilled holes and using nuts and bolts provided. 5.

on inside of doors Inside Face A (ii) Attaching Clip-on Hinges Door Cabinet (iii) Drawing showing Door adjustment by screw on mounting plate 5b Step 4 - Mounting Bi-Fold Doors * Attach interfold hinges to door panel edges to form two sets of bi-fold doors. * Insert clip-on hinges into hinge holes on outside edges of door panels. Fix hinges to doors using screws provided. * Attach doors to cabinet by clipping hinges onto mounting plates on cabinet end panels. * Adjust doors if necessary by screw adjustment where hinge meets hinge plate. Note: Ensure that butt of hinge is on inside of doors * Attach handles to doors. 6. DIAGRAM 5

2227mm Wall 464 117 2108 150 2 7. Carcase Construction DIAGRAM 11 1655mm Queen 505 Min 464mm For 250mm thick mattress NOTE: ALL BASED ON 16mm BOARD CONSTRUCTION 16