TIL TDFM-9300 Installation Instructions Manual

Installation Instructions TiL Document No. 13RE471 Rev. D Issue 5 NOVEMBER 2015 Technisonic Industries Limited 240 Traders Boulevard, Mississauga, Ontario L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 www.til.ca Copyright by Technisonic Industries Limited. All rights reserved.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 i REVISION HISTORY [ 13RE471 ] For the most current revision of this document, please check the Technisonic website: www.til.ca REV PAGE DESCRIPTION DATE EDITED BY A iv Corrected DO-160 Information. Jul. 2013 SM Front Page Front Panel Image changed. Oct. 2013 AL A – 1 1 to 5 Fixed Radio P/N Nomenclature. Nov. 07, 2013 JR A – 2 7 P/N in Section 2.4 Corrected. Jan. 27, 2014 AL All Corrected Spelling & Grammar throughout document. B iv Changed Installation Approval Note. May 15, 2014 AL 2 Added Special Order Band Codes. 2 and 14 Specified “Section 2.17 Configuration Menu” Refers to TDFM-9300 Operating Instructions. 9 Added Antenna & Connector Locations as well as Band Display Orientation. 15 to 19 Updated Figures 4 – 8. All Changed Format for Section Headers. C iv Changes made to DO-160G: - Operational Shock and Crash Safety changed to Category B. - Flammability Condition added. Sep. 10, 2015 AL iv Corrected Installation Approval Note. All Page Numbers are now sequential. D iv Flammability Category C refers to Mod 6 only. Nov. 09, 2015 AL 33 to 35 Added Environmental Qualification Form. D – 1 15 to 19 Updated Figures 4 – 8. Feb. 16, 2016 AL D – 2 All Added band info on new Tri Band RF module. Apr. 29, 2016 JR D – 3 i Added Website Information to Revision Page. Oct. 05, 2016 AL 15 to 19 Updated Figures 4 – 8. 20 Minor text fixes. 21 Added Section 2.23: Post Installation Adjustment. D – 4 25 Updated Test Frequencies. Feb. 13, 2018 SM D – 5 All Updated to MCP (MOD14). Oct. 10, 2019 SM

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 ii This page is intentionally left blank.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 iii ESD CAUTION This unit contains static sensitive devices. Wear a grounded wrist strap and/or conductive gloves when handling printed circuit boards. FCC COMPLIANCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: For compliance with FCC RF Exposure Requirements the mobile transmitter antenna installation shall comply with the following two conditions: 1. The transmitter antenna gain shall not exceed 3 dBi. 2. The transmitter antenna is required to be located outside of a vehicle and kept at a separation distance of 70 cm or more between the transmitter antenna of this device and persons during operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense. WARNING AND DISCLAIMER Changes or modifications not expressly approved by Technisonic Industries could void the user’s authority to operate the equipment. This manual is designed to provide information about the TDFM-9300. Every effort has been made to make this manual as complete and accurate as possible. WARRANTY INFORMATION The Model TDFM-9300 Transceiver is under warranty for one year from date of purchase. Failed units caused by defective parts or workmanship should be returned to: Technisonic Industries Limited 240 Traders Boulevard Mississauga, Ontario L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 NOTES

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 iv SUMMARY OF DO-160G ENVIRONMENTAL TESTING Summary of DO-160G Environmental Testing for Technisonic Model TDFM-9300 Transceiver: CONDITIONS CATEGORY Temperature and Altitude A2, B1, C4, D1 Temperature Variation B Humidity A Operational Shock and Crash Safety B Vibration S, U Magnetic Effect Z Power Input B Voltage Spike B Audio Frequency Susceptibility B Induced Signal Susceptibility AC Radio Frequency Susceptibility T Radio Frequency Emission M Electrostatic Discharge A Flammability C* * Only applies to units with “MOD 6” marked on the modifications label. For more detailed information, see Appendix A. INSTALLATION APPROVAL NOTE Presently, no TSO standard exists for airborne FM transceivers. To make it easier for installation agencies to provide their customers with an approved installation supported by an effective Airworthiness Approval, Technisonic has secured Supplemental Type Certificate (STC) Approvals on its Airborne FM products for a limited number of airframes. The above referenced DO-160G test data is also on file and available from Technisonic to support approval requirements in airframes for which Technisonic does not possess an STC. Approved aircraft types are listed in the attachments to the formal STC documents. These STCs are the exclusive property of Technisonic and require the written authority of Technisonic for their use. Letters of permission are provided upon request. To assist Factory Authorized Technisonic Dealers in the certification process, we have placed copies of our STCs on our website. These documents may be downloaded and used as support for the technical submission to FAA or Transport Canada. Only authorized factory dealers/installers are permitted to download and make use of these documents on behalf of their customers (end users) in support of regulatory agency approval. Please refer to the Technisonic website www.til.ca for the latest issue of available STCs. TRADEMARK NOTICES TDFM-9300 Transceivers contain two-way radio protocols licensed from Motorola, Inc. © 1997, 1998 Motorola, Inc. Motorola KVL 3000+® is a registered trademark of Motorola.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 v SECTION TITLE PAGE 1 GENERAL DESCRIPTION B 1.1 INTRODUCTION ............................................................................................................ 1 1.2 DESCRIPTION ............................................................................................................... 1 1.3 MODEL VARIATION ...................................................................................................... 2 1.4 TECHNICAL CHARACTERISTICS ................................................................................ 4 2 INSTALLATION INSTRUCTIONS B 2.1 GENERAL ...................................................................................................................... 7 2.2 EQUIPMENT PACKING LOG ........................................................................................ 7 2.3 INSTALLATION .............................................................................................................. 7 2.4 INSTALLATION KIT – CONTENTS ............................................................................... 7 2.5 ANTENNA INSTALLATION ............................................................................................ 7 2.6 INSTALLATION – PIN LOCATIONS AND CONNECTIONS ......................................... 10 2.7 INSTALLATION – WIRING INSTRUCTIONS ................................................................ 14 2.8 MAIN GROUND – J1 PINS 1 AND 14 ........................................................................... 14 2.9 MAIN POWER + 28 VDC – J1 PINS 2 AND 15 ............................................................... 14 2.10 MIC 1, 2, 3, 4, AND 5 – J1 PINS 3, 6, 9, J6 PIN 6, AND P1 PIN 15 ............................... 14 2.11 MIC COMBINED 1 AND 2 – J6 PINS 7 AND 13 ............................................................ 14 2.12 AUDIO 1, 2, 3, AND 4 – J1 PINS 4, 7, 10, J6 PIN 5, AND P1 PIN 6 ............................. 14 2.13 AUDIO COMBINED 1 AND 2 – J6 PINS 2 AND 10 ....................................................... 14 2.14 PTT 1, 2, 3, 5, 6, AND 4 – J1 PINS 5, 8, 11, 21, 24, AND J6 PINS 3 ........................... 14 2.15 PTT COMBINED 1 AND 2 – J6 PINS 4 AND 12 ........................................................... 14 2.16 TX DATA AND RX DATA – J1 PINS 12 AND 13 ........................................................... 15 2.17 UP AND DOWN – J1 PINS 16 AND 17 .......................................................................... 15 2.18 CHANNEL/BAND – J1 PIN 18 ........................................................................................ 15 2.19 PANEL BACKLIGHTING – J1 PIN 25 ............................................................................. 15 2.20 SPEAKER LO AND HI – J6 PINS 8 AND 9 ................................................................... 15 2.21 ANTENNA TUNER CONTROL LINES: P1 (PINS 1, 2, 3, 4, 5, 6, 10, AND 12) ............ 15 2.22 ANTENNA SELECTION AND INSTALLATION CONSIDERATIONS ............................. 21 2.23 POST INSTALLATION ADJUSTMENT .......................................................................... 22 2.24 POST INSTALLATION EMI TEST ................................................................................. 24 APPENDIX A Support Notes .......................................................................................... 35 ENVIRONMENTAL QUALIFICATION FORM ................................................................ 36 WARRANTY ................................................................................................................... 38 TABLE OF CONTENTS

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 vi FIGURE TITLE PAGE 1 Outline Drawing .............................................................................................................. 8 2 TDFM-9300 Antenna & Connector Locations ................................................................ 9 3 TDFM-9300 Band Display Orientation ........................................................................... 9 4 Wiring Connections for Individual Band Control ............................................................ 17 5 Wiring Connections for Combined Band Control ........................................................... 18 6 Wiring Connections for MCP Features ........................................................................... 19 7 Wiring Connection Notes for the TDFM-9300 Transceiver ............................................ 20 TABLE TITLE PAGE 1 J1 25-Pin D Connections ................................................................................................ 10 2 J6 15-Pin High Density D Connections .......................................................................... 11 3 J5 15-Pin High Density D Connections .......................................................................... 11 4 J9 26-Pin High Density D Connections .......................................................................... 12 5 P1 15-Pin High Density D Connections ......................................................................... 13 6 List of External Radio Interface Cables .......................................................................... 16 LIST OF FIGURES LIST OF TABLES

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 1 1.1 INTRODUCTION This publication provides operating information on the TDFM-9300 airborne transceiver. The exact configuration depends on which and how many RF modules are installed. 1.2 DESCRIPTION The TDFM-9300 transceiver is an airborne multi-band radio capable of operation in conventional analog FM, AM, P25 digital FM systems, SmartNet/SmartZone trunking systems, and P25 9600 trunking systems. RF modules are available in single, dual or tri bands that support various combinations of VHF LO, VHF AM, VHF FM, UHF-LO, UHF-HI, UHF AM and 700-800 MHz bands. Up to 4 single or multiple band P25 digital modules and one analog only module can be supported. These optional additional features include P25 9600 trunking Phase 1 and 2 that may be combined with AES and/or DES-OFB encryption with OTAR in any of the available modules. Bands 1 through 4 on the TDFM-9300 are not normally frequency agile. In order to have the ability to change the frequencies at the front panel, the FPP (front panel programming) option must be ordered for each band. FPP is available on all bands of modules. The TDFM-9300 has provisions for four of the above RF modules as well as one analog only module. This additional module is fully frequency programmable from the front panel. Analog only modules support CTCSS, DCS, wide, and narrow band operation where applicable. TDFM-9300 transcievers with MOD 14 (MCP) have the capability to provide PTT, mic and headset for up to 2 (bands 7 and 8) remote handheld transceivers and/or a Latitude Technologies S200-P12 satphone / PTT network com transceiver. Front panel control of the S200-P12 is provided via the display and keypad. Connector J9 provides the MOD 14 interface. See table 6 for a list of recommended interface cables for various hand held transceivers. A digital audio port has been added to interface with the Technisonic TDAP-650 and TDAP-750 digital audio panels. SECTION 1: GENERAL DESCRIPTION

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 2 1.3 MODEL VARIATION There are several variations of the Model TDFM-9300 Transceiver. Each variation offers different features and performance based on the type of RF modules and options installed. RF Modules are mounted in trays of two with up to 3 trays supported. The Analog module occupies one single tray. The following is a breakdown of the TDFM-9300 model variations: P/N 111267-D-93-TBB-TBB-TB-P93XXX (PRODUCT TYPE)-(D)-(9X)-(Tray 1)-(Tray2)-(Tray3)-(Project) PRODUCT TYPE: 111267 = TDFM 9300 series, 3 trays, 1 to 4 P25 modules and one Analog module D= Display type: 1) Color TFT 2) Standard Green/NV 9X = TDFM-9000 series variant: 93 = TDFM-9300 Tray Breakdown: (TBB): T = Module type: A = T30xx RF modules (Single or Dual) or T4000 (Tri Band), T = T3x00 Analog only RF module. B = Band Code for each module in the tray. See the following tables for supported configurations. DUAL BAND MODULES (T30xx) TRI BAND MODULES (T4000) SINGLE BAND 1 VHF 5 VHF 2 UHF LO 6 UHF LO 3 UHF HI 7 UHF HI 4 700/800 8 700/800 DUAL BAND A VHF 700/800 M VHF 700/800 B VHF UHF LO N VHF UHF LO C VHF UHF HI P VHF UHF HI D UHF LO UHF HI R UHF LO UHF HI E UHF LO 700/800 T UHF LO 700/800 F UHF HI 700/800 V UHF HI 700/800 * G 700/800 VHF - * H 700/800 UHF LO - * I 700/800 UHF HI - * J UHF LO VHF - * K UHF HI VHF - * L UHF HI UHF LO - TRI BAND - W VHF UHF LO UHF HI - X UHF LO UHF HI 700/800 - $ Z VHF UHF 700/800 TYPE A Band Codes

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 3 TYPE T Analog Band Codes BAND FREQUENCY RANGE VHF 136 – 174 MHZ UHF LO 380 – 470 MHZ UHF HI 450 – 520 MHZ 700/800 764 – 870 MHZ UHF 380 – 520 MHZ VHF LO 30 – 50 MHZ VHF AM 118 – 136 MHZ UHF AM 225 – 400 MHZ RF Band Coverage Band numbers indicate Single band equipped modules and letters indicate Dual or Tri band modules. * Band codes are special order and are not standard configuration. $ UHF Band specified covers both the UHF LO and UHF HI as one band. (380 – 520 MHz). Project Number: P93XXX represents a 5 digit project number that identifies specific options that are contained in each module and describes the full TDFM-9300 configuration. All model variations are capable of supporting both 28 volt and 5 volt AC or DC backlighting. The units are shipped set to operate on 28 volt backlighting. Equipment can be set to operate on 5 V backlighting by using the software based configuration menu. See Section 2.17 Configuration Menu in the TDFM-9300 Operating Instructions manual available at www.til.ca. Damage will not occur if the incorrect voltage is applied. ANALOG RF MODULES (T3x00) 1 VHF LO 4 VHF AM 5 UHF AM

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 4 1.4 TECHNICAL CHARACTERISTICS Specification Characteristic Model Designation: TDFM-9300 Physical Dimensions: Approx. (L) 8.0" x (W) 5.75" x (H) 4.5" Weight: ~7.0 Lbs (3.2 Kg) Operating Temperature Range: Storage Temperature Range: -30° C to +60° C -40° C to +80° C Power Requirement: Voltage: Current: 28.0 VDC ± 15% 500 mA minimum / 7.5A maximum Audio Output Power (including sidetone): 65 mW into 600Ω Microphone Inputs: Carbon or Equivalent Panel Back Lighting: Voltage: Current: 28 or 5 Volts AC or DC (selectable) 100 mA RF Modules Specification Characteristic RF Output Power: 1 or 6 Watts (VHF) 1 or 5 Watts (UHF) 1 or 2.5 Watts (764 – 806) 1 or 3 Watts (806 – 870) Frequency Range VHF Band: UHF LO Band: UHF HI Band: UHF Band: 700 / 800 Bands: 136 to 174 MHz 380 to 470 MHz 450 to 520 MHz 380 to 520 MHz 764 to 870 MHz No. of channels per band: 3000 pre-programmable channels Transmitter section VHF UHF 800 FM Hum and noise in dB (wideband): Audio Distortion: Frequency Stability in ppm: Modulation Limiting: -48 -45 -45 1% 1.0% 1.0% ± 1.0 ± 1.0 ± 1.5 Wide band ± 5 kHz Narrow band ± 2.5 kHz Receiver section VHF UHF 800 Sensitivity in uV: * Digital 1% BER (12.5 kHz) * Digital 5% BER (12.5 kHz) ** Analog with 12 dB SINAD 0.29 0.32 0.40 0.21 0.28 0.30 0.25 0.25 0.25 Selectivity in dB: 25 kHz Channel 12.5 kHz Channel Intermodulation * ** -80 -78 -72 -70 -68 -67 -80 -80 -80 * Measured in digital mode per TIA / EIA IS 102.CAAA under nominal conditions. ** Measured in analog mode per TIA / EIA 603 under nominal conditions.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 5 ANALOG MODULE SPECIFICATIONS GENERAL Frequency Ranges: VHF FM Lo module 30 - 50 MHz VHF AM module 118 - 137 MHz UHF AM module 225 - 400 MHz Operating Mode: F3E simplex or semi-duplex (FM modules) A3E simplex (AM modules) Channel Spacing: 25 or 12.5 kHz (25 kHz only for AM) FM Frequency Selection: via front panel 200 memories per band programmed with: a) TX Frequency/RX Frequency b) TX/RX CTCSS tone or DPL code c) 9-character alphanumeric title CTCSS squelch/encoder: * All CTCSS tones available (FM modules only) DPL digital squelch/encoder: * All standard DPL codes (FM modules only) DTMF encoder: All standard DTMF tones * Available only on FM Modules. VHF LO FM RECEIVER Sensitivity at 12 dB SINAD Better than 0.35 µV Adjacent Channel Selectivity -75 dB (25 kHz) -70 dB (12.5 kHz) Spurious Attenuation -90 dB Third Order Intermodulation -70 dB Image Attenuation -80 dB FM Acceptance ± 6 kHz Hum and Noise Better than 45 dB Audio Distortion Less than 5% Antenna Conducted Emission Less than -70 dBm VHF LO FM TRANSMITTER RF Power Output 1 watt or 10 watts Output Impedance 50 ohms Maximum Deviation ± 5 kHz (25 kHz mode) (In narrowband mode) ± 2.5 kHz (12.5 kHz mode) Spurious Attenuation -90 dB below carrier level Frequency Stability ± 2.5 ppm Harmonic Attenuation -60 dB below carrier level FM Hum And Noise -40 dB Audio Input 50 mV at 2.5 kHz into 200 ohms input circuit for ± 3.5 kHz deviation, adjust. Audio Distortion Less than 5%

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 6 VHF AM RECEIVER Sensitivity at 12 dB SINAD Better than 2.0 µV Adjacent Channel Selectivity -70 dB (25 kHz) Spurious Attenuation -70 dB Third Order Intermodulation -70 dB Image Attenuation -60 dB Hum and Noise Better than 40 dB Audio Distortion Less than 5% Antenna Conducted Emission Less than -70 dBm VHF AM TRANSMITTER RF Power Output 5 watts (2.5 watts carrier) Output Impedance 50 ohms Maximum Modulation (max) 95% Maximum Modulation (min) 75% Spurious Attenuation -60 dB below carrier level Frequency Stability ± 2.5 ppm Harmonic Attenuation -60 dB below carrier level Signal to Noise Ratio -35 dB Audio Input 50 mV at 2.5 kHz into 200 ohm input circuit for 30% modulation (adjustable) Audio Distortion Less than 5% UHF AM RECEIVER Sensitivity at 12 dB SINAD Better than 4.0 µV Adjacent Channel Selectivity -70 dB (25 kHz) Spurious Attenuation -70 dB Third Order Intermodulation -70 dB Image Attenuation -60 dB Hum and Noise Better than 40 dB Audio Distortion Less than 5% Antenna Conducted Emission Less than -70 dBm UHF AM TRANSMITTER RF Power Output 3 to 4 watts carrier Output Impedance 50 ohms Maximum Modulation (max) 95% Maximum Modulation (min) 75% Spurious Attenuation -60 dB below carrier level Frequency Stability ± 2.5 ppm Harmonic Attenuation -60 dB below carrier level Signal to Noise Ratio -35 dB Audio Input 50 mV at 2.5 kHz into 200 ohm input circuit for 30% modulation (adjustable) Audio Distortion Less than 5%

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 7 2.1 GENERAL This section contains information and instructions for the correct installation of the TDFM-9300 Transceiver. 2.2 EQUIPMENT PACKING LOG Unpack the equipment and check for any damage that may have occurred during transit. Save the original shipping container for returns due to damage or warranty claims. Check that each item on the packing slip has been shipped in the container. 2.3 INSTALLATION The TDFM-9300 Transceiver is designed to be Dzus mounted and should be installed in conjunction with an IN-9300 installation kit. See Figure 1 for an outline drawing of the unit with dimensions to facilitate the installation. 2.4 INSTALLATION KIT – CONTENTS The IN-9300 installation kit (P/N 129292) consists of: 1. One 25-Pin Cannon D mating connector (female) complete with crimp pins and hood. 2. Two 15-Pin HD Cannon D mating connector (female) complete with crimp pins and hood. 3. One 15-Pin HD Cannon D mating connector (male) complete with crimp pins and hood. 4. One 26-Pin HD Cannon D mating connector (female) complete with pins and hood. 5. 5 BNC connectors. 2.5 ANTENNA INSTALLATION The type and number of antennas depends on the model of transceiver being installed. The following is a list of recommended antennas for the various RF modules: VHFLO 30 to 50 MHz Foxtronics Part # FLX-3050B or Sensor Systems Part # S65-8282-34* VHF AM 118 to 138 MHz Comant Part # CI-292-1 VHF 136 to 174 MHz Comant Part # CI-292-3 or -4 UHFLO 403 to 470 MHz Comant Part # CI-275 UHFHI 450 to 520 MHz Comant Part # CI-285 800 800 to 870 MHz Comant Part # CI-306 800/700 764 to 870 MHz Comant Part # CI-285 VHF/UHF/700/800 136 to 870 MHz Rami Part # AV-925 The antenna should be mounted on the bottom of the aircraft whenever possible. Consult with instructions provided with the antenna. Connect the RF cables to the back of the transceiver using the MALE BNC connectors provided in the installation kit. It is possible to use equivalent 50 ohm aviation antennas that cover the appropriate bandwidths. SECTION 2: INSTALLATION INSTRUCTIONS

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 8 FIGURE 1: Outline Drawing for Model TDFM-9300

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 9 FIGURE 2: TDFM-9300 Antenna & Connector Locations FIGURE 3: TDFM-9300 Band Display Orientation Band display corresponds to the antenna connector numbering and radio ports. Band 1 (top of the display) is connected the ANT 1 and uses the Band 1 connections on the interface connectors. BANDS 1 2 3 4 5

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 10 2.6 INSTALLATION – PIN LOCATIONS AND CONNECTIONS J1 (25-Pin D Connections) - Use FEMALE Connector PIN # DESCRIPTION 1 Ground 2 Main Power +28 VDC 3 Mic 1 4 Audio 1 5 PTT 1 6 Mic 2 7 Audio 2 8 PTT 2 9 Mic 3 10 Audio 3 11 PTT 3 12 TX Data 13 RX Data 14 Ground 15 Main Power +28 VDC 16 Up 17 Down 18 Channel / Band 19 Mic 5 20 Audio 5 21 PTT 5 22 Mic 6 23 Audio 6 24 PTT 6 25 Panel Backlighting TABLE 1: J1 (25-Pin D) Connections

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 11 J6 (15-Pin High Density D Connections) – Use FEMALE Connector PIN # DESCRIPTION 1 Ground 2 Audio Combined 1 3 PTT4 4 PTT Combined 1 5 Audio 4 6 Mic 4 7 Mic Combined 1 8 Speaker Lo 9 Speaker Hi 10 Audio Combined 2 11 Misc In 12 PTT Combined 2 13 Mic Combined 2 14 Misc In/Out 15 Audio Combined Ground 2 TABLE 2: J6 (15-Pin HDD) Connections J5 (15-Pin High Density D Connections) – Use MALE Connector PIN # DESCRIPTION 1 Audio 2 2 Audio 5 3 Audio 6 4 Audio 3 5 Audio 4 6 Audio Ground 2 7 Audio Ground 5 8 Audio Ground 6 9 Audio Ground 3 10 Audio Ground 4 11 Audio 1 12 Audio Ground 1 13 Ground 14 Audio Combined Ground 1 15 Audio Combined 1 TABLE 3: J5 (15-Pin HDD) Connections

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 12 J9 (26-Pin High Density D Connections) – Use FEMALE Connector PIN # DESCRIPTION 1 Ground 2 Ground 3 Ground 4 Ground 5 Ground 6 Ground 7 S200-P12 TX Data 8 Not Used 9 Digital Audio Panel Data In 10 Band 7 Mic Out 11 Band 8 Mic Out 12 Band 7 PTT Out 13 Band 8 PTT Out 14 Band 7 Audio Out 15 Band 8 Audio Out 16 Not Used 17 Not Used 18 Not Used 19 Band 7 Mic In 20 Band 8 Mic In 21 Band 7 PTT In 22 Band 8 PTT In 23 Band 7 Audio In 24 Band 8 Audio In 25 S200-P12 RX Data 26 Digital Audio Panel Data Out TABLE 4: J9 (26-Pin HDD) Connections (MOD 14 Only)

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 13 P1 Connections (15-Pin [High Density] FEMALE D Connector) PIN # DESCRIPTION 1 4 MHz 2 8 MHz 3 10 MHz 4 20 MHz 5 40 MHz 6 No connection 7 No connection 8 No connection 9 No connection 10 Tune Indicator 11 No connection 12 Tune Enable 13 Ground 14 No connection 15 No connection TABLE 5: P1 15-Pin High Density D Connections

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 14 2.7 INSTALLATION – WIRING INSTRUCTIONS Figures 4 – 7 show all required connections and recommended wire sizes for the TDFM-9300 transceiver. There are receive audio, mic audio, and Push To Talk (PTT) lines for each band as well as two sets of lines combining all bands. The TDFM-9300 can be wired such that band selection can be made on the audio panel. Up to 7 positions need to be available on the audio panel; otherwise, the TDFM-9300 can be wired into one or two positions of the audio panel where band selection and audio monitoring are done on the TDFM-9300 front panel. An installation can be wired in a combination of both methods since all inputs and outputs are always active. 2.8 MAIN GROUND – J1 PINS 1 AND 14 Both pins should be connected to power ground. These pins are internally connected to the chassis. 2.9 MAIN POWER + 28 VDC – J1 PINS 2 AND 15 Both pins should be connected to +28 volts DC +/- 15%. 2.10 MIC 1, 2, 3, 4, 5, 7 AND 8 – J1 PINS 3, 6, 9, J6 PIN 6, J9 PINS 19 AND 20 The microphone input signals shall be connected using shielded wire with the shield connected to ground (Pin 1 or 14). It is recommended for best results to leave the other end of the shield floating to prevent ground currents unless you are connecting to an audio panel with floating hi and lo inputs (like the Technisonic A710, A711 or A711L) in which case the shield must be connected to the lo input. These are individual inputs for each band. 2.11 MIC COMBINED 1 AND 2 – J6 PINS 7 AND 13 The combined mic inputs should be wired and shielded as the individual mic inputs above. These mic inputs can be used for any band. Band selection is made at the TDFM-9300 front panel. 2.12 AUDIO 1, 2, 3, 5, 4, 7 AND 8 – J1 PINS 4, 7, 10, 20, J6 PIN 5, J9 PINS 14 AND 15 These are individual audio outputs from each band. All outputs are 600 ohms impedance. The output power is 65 mW maximum. Unused outputs do not need to be terminated and should be left unconnected. 2.13 AUDIO COMBINED 1 AND 2 – J6 PINS 2 AND 10 These are combined audio outputs from all bands as selected from the front panel. The specifications are the same as the individual outputs above. 2.14 PTT 1, 2, 3, 5, 4, 7 AND 8 – J1 PINS 5, 8, 11, 21, J6 PIN 3, J9 PINS 21 AND 22 There are individual PTT lines for each band. These lines should be floating when in receive mode and grounded for transmit. The input has a pull up resistor to 5 volts. Connecting an audio panel that wishes to see more may result in no receive audio. Connect a 1N4006 diode in series with the cathode towards the audio panel in this case. 2.15 PTT COMBINED 1 AND 2 – J6 PINS 4 AND 12 These are combined PTT inputs to all bands as selected from the front panel. The specifications are the same as the individual inputs above.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 15 2.16 TX DATA AND RX DATA – J1 PINS 12 AND 13 These pins provide RS-232 serial communications for use with the RC-9000 remote control head if installed. Consult the RC-9000 installation manual for details. 2.17 UP AND DOWN – J1 PINS 16 AND 17 These pins can be used to scroll up and down through the bands or channels for the band currently selected depending on the band input below. The inputs normally floating are grounded to activate. Two push buttons or a center off, SPDT, spring-loaded toggle switch are typically used on these inputs. 2.18 CHANNEL/BAND – J1 PIN 18 The Channel / Band input determines the function of the up down inputs above. If left unconnected, the inputs are for channel selection. If grounded, the input is for band selection. 2.19 PANEL BACKLIGHTING – J1 PIN 25 Connect to aircraft panel dimming bus. The transceiver is capable of supporting 28 VAC/DC or 5 VAC/DC backlighting circuits. Select 28 volts or 5 volts via the configuration menu (see Section 2.17 in the TDFM-9300 Operating Instructions manual). No damage will occur if the wrong setting is made. 2.20 SPEAKER LO AND HI – J6 PINS 8 AND 9 Not normally connected in the aircraft. This output is 4 / 8 ohms at 1.1 watts max and has the audio associated with Audio Combined 1. This output does not have to be terminated when not used and should be left unconnected. 2.21 ANTENNA TUNER CONTROL LINES: P1 (PINS 1, 2, 3, 4, 5, 10, AND 12) These connections are to control an antenna tuner system such as the Foxtronics FLX-3050B. Connect according to the manufacturer’s instructions. In the case of the FLX-3050B, the tune indicator (which is normally connected to a light) can be connected to Pin 10 so that the tuning indication will show on the TDFM-9300 display. If a passive antenna is used, these lines shall remain unconnected.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 16 HAND HELD TRANSCEIVER MODEL CABLE PART NUMBER Motorola Moto-Turbo XPR-6300/6350/6500/6550, SRX-2200, APX-6000/7000/8000 179.6550 Motorola XTS-1500/2500/3000/5000, EFJ-5000, VP Series 179.0630 Harris / Ma/com Jaguar P5300/P5400/P7300, XG75 179.7370 Harris / Ma/com Unity XG-100, XL-200P 179.0641 Kenwood TK190/280/290/380/390/480/481/2140/3140/2180/3180/5210/5400 179.0136 Kenwood NX200, NX300 179.0136 Kenwood TK208/220/240D/248/250/260/270/308/320/340D/348/350/353/360/370/ 430/431272G/372G/3130/3131 179.6013 Icom F30/40/50/60/70/80 179.0160 Icom F3/3S/4/4S/4TR/10, IC-H2/H6/J12/M5/U12/U16 179.0737 Icom A6, F11/11S/14/21/21S/33GS/33GT/43GS/43GT/43TR 179.0748 Yeasu Vertex VX-500/510/520 179.0138 Yeasu Vertex VX-10/210/210A/131/160/180/300/400/410/420 179.0746 Bendix King Relm KNG P150, P400, P500, P800 179.0745 Sincgars PRC-117, MBITR 179.0600 TABLE 6: List of External Radio Interface Cables NOTE: All the above cables interface the TDFM-9300 via a panel mounted locking DIN connecter P/N 244.0070.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 17 FIGURE 4: Wiring Connections for Individual Band Control

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 18 FIGURE 5: Wiring Connections for Combined Band Control

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 19 FIGURE 6: Wiring Connections for MCP Features

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 20 FIGURE 7: Wiring Connection Notes for the TDFM-9300 Transceiver

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 21 2.22 ANTENNA SELECTION AND INSTALLATION CONSIDERATIONS Antenna installations will vary according to the number / type of bands installed in the TDFM- 9300, types of antennas selected, and space available on the aircraft. The materials list above contains many but not all antennas available. If dual or tri band RF modules are installed in the TDFM-9300, it is suggested to use a single connector, multiband antenna for each of the RF modules installed. When single band modules are installed, a single band antenna should be used. If the TDFM-9300 has more than one single band module installed on different frequency bands, a single multiband antenna with separate connectors or a multiband antenna with a coupler can be used if the frequencies in use are not multiples of each other. For example, transmitting near 150 MHz on VHF may interfere with frequencies near 450 MHz on the UHF band. Antennas should be spaced as far as possible from each other with the Comm antennas on the opposite side (top or bottom) from the FM antennas. The following example uses a single RAMI AV-925 antenna and triplexer AV-926 with up to three single band modules operating in the following Frequency ranges: • 136-174 MHz • 380-520 MHz • 764-870 MHz

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 22 2.23 POST INSTALLATION ADJUSTMENT In most cases, factory audio settings will work; however, if there is a need to adjust audio levels to match the audio controller system, then they can be adjusted in the Maintenance Menu. To reach the Maintenance Menu, press FUNC – NEXT and select Configuration from the 2nd side button. Then press the MODE key. First Page – TX Mic Gains Mic 1 Level: 24 The Mic gain levels can be adjusted from 0 to 40 with a typical factory setting of 22 to 24 (Band 5 is 20). The higher the number, the more sensitive the mic input is. The factory setting gives approximately 1.5 kHz deviation for – 13 dBm for a 600 ohm system. Highlight the desired band by pressing the corresponding side button. Key the selected band and rotate the knob to adjust the mic gain to a desired level. Unkey the radio. Repeat for the other bands as required. Press NEXT to reach the next screen. Second page - RX audio levels. RX Audio 1 level: 14 This page sets the MAX RX audio level the volume has when set to 40 on the normal operational display screen. The maximum RX audio level on each module installed can be adjusted from 0 to 40 with a typical factory setting for bands 1 to 4 of 10 to 14 for 5 Vrms for 600 ohm load. Band 5 is 30 to 35. The higher the number, the higher the max audio is. Highlight the desired band by pressing the corresponding side button. Rotate the knob to adjust the Maximum RX level. Repeat for other bands as required. Note: The factory level is optimized for highest level with the lowest distortion. Adjusting further than factory settings will result in little gain and higher RX distortion. Normally this level should only be lowered if the audio controller needs a lower level of drive. Press NEXT to reach the next screen. Third Page – Keypad Backlight Calibration Keypad Calibration – 28 VDC; 1800 Keypad Calibration – 5 VAC: 400 The keypad backlight maximum brightness can be adjusted here. The two menus available are 28V and 5V. The active menu depends on the Backlight Mode selected in the Configuration Menu. The 28V menu can be adjusted if the radio is set for 28V, or the 5V menu can be adjusted if the radio is set for 5V. The 28V menu is adjustable from 500 to 2500 and the 5V is adjustable from 100 to 1000. The calibration value determines the maximum brightness the keypad will be allowed to go to when the max back light voltage is applied the back light buss input. The higher the number, the lower the brightness. This feature maybe useful for matching the NV backlighting of the TDFM- 9300 to the airframe installation setup. In the Configuration Menu, select the Backlight Mode – 28 VDC or 5 VAC (5th item). Set the dimming bus in the airframe to maximum value. Rotate the knob to adjust the max brightness of the keypad to the desired level.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 23 Mod 7 Menu: Enabled The Mod 7 menu should be set on if the radio’s modification record label has Mod 7 marked. Otherwise, it should be disabled. Highlight the menu and rotate the knob to adjust as required. NOTE: This is a factory setting and should not be adjusted in the field unless directed to do so. Press NEXT to reach the next screen. Fourth Page - Band 5 TX Power and Squelch Settings. RFM 5 RX Sqlch 215 This sets the Receive Squelch level for the analog RF module installed in Band 5 slot. The Squelch can be set from 0 to 255. The typical factory setting is 215. Highlight the Menu and rotate the knob to adjust as required. The higher the number, the tighter the squelch. RFM 5 TX HI PWR 235 This sets the Transmit HI Power level for the VHF Low Band RF Module for radios so equipped. TX power can be adjusted from 0 to 255, with a typical factory setting of 235 for 10 W output. Highlight the Menu, key the module, and rotate the knob to adjust as required. RFM 5 TX LO PWR 064 This sets the Transmit LO Power level for the VHF Low Band RF Module for radios so equipped. TX power can be adjusted from 0 to 255, with a typical factory setting of 064 for 1 W output. Highlight the Menu, Key the module and rotate the knob to adjust as required. NOTE: The Transmit Power Menus are not available for radios equipped with VHF AM and UHF AM RF modules. Transmit power is fixed. Press ESC to return to normal operation.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 24 2.24 POST INSTALLATION EMI TEST PURPOSE The purpose of this test is to identify any interference that the TDFM-9300 transceiver may cause with existing aircraft systems. TEST CONDITIONS The TDFM-9300 transceiver should be installed and function tested. The antenna VSWR should be checked. A forward/reverse power check with an in-line wattmeter should show no more than 10% reflected power. For the following tests, ensure that the output power is set to high. METHODOLOGY Most of the EMI tests can be accomplished on the ground. In some cases, flight testing is required or is easier. If the aircraft is approved for IFR operations, then it is mandatory that interference between the TDFM-9300 transceiver and the approach aids be checked in flight. The GPS should be operational and navigating with at least the minimum compliment of satellites. The VHF comm should be set to the frequencies indicated with the squelch open. VOR/DME receivers should be set to the frequencies indicated and selected for display. If possible, set up a DME ramp test set on the frequencies indicated and adjust the output until the flags are out of view. The transponder and encoder should be monitored with ramp test equipment. Set the output of the transponder test set to 3db above the output necessary to achieve 90% reply. If possible, set the ADF to a nearby navigation station. Modulate the TDFM-9300 transmitter on the indicated frequencies for at least 20 seconds. Observe the GPS for any degradation in satellite status or availability or flags. Listen for any noise or detected audio signals on the VHF comm(s). Listen for any noise or detected audio signals on the VOR/LOC receiver audio; look for any moment of flags or needles on the VOR/LOC/GS navigation display(s). Observe the transponder for any loss of reply or spurious reply. List the power plant, fuel, and other electric instruments in the chart provided and note any anomalies that occur while transmitting. Assess the results. If the aircraft is equipped with an autopilot or a stability augmentation system, then test fly the aircraft and verify that operation of the TDFM-9300 transceiver does not have adverse effects on these systems. After checking for gross effects at a safe altitude, fly an approach with each of the different navigation systems coupled to the autopilot (ILS, GPS, etc.) and look for any anomalies. RESULTS If the installed system passes all of the applicable EMI tests, then no further action is required. If interference is observed, then the interference must be assessed against the appropriate standards of airworthiness for the system in question. For example, it is permissible for a VFR certified GPS to lose navigation capability while the TDFM-9300 unit is transmitting, providing that it recovers properly and promptly, but it is not permissible for an IFR Approach certified GPS to be affected in the same way. A complete discussion of all the standards of airworthiness to be applied in assessing EMI effects is beyond the scope of this document.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 25 PROCEDURE A. Operate the TDFM-9300 transmitter on the following frequency for at least 20 seconds. Observe the GPS for any degradation in satellite status or availability or flags. FREQUENCIES GPS #1 GPS #2 TDFM-9300 PASS FAIL PASS FAIL 143.2125 MHz 143.2250 MHz 157.5375 MHz 157.5500 MHz 512.0000 MHz 39.3850 MHz NOTES:

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 26 B. Determine if the image frequency for the VHF Comm falls within the range of the TDFM- 9300. If so, select a set of frequencies that will cause the TDFM-9300 to be set as close as possible to the image frequency. Any one of the many possible sets will suffice. Record those values in the spaces provided in the following chart. Modulate the TDFM- 9300 transmitter on the following frequencies for at least 20 seconds. Listen for any noise or detected audio signals on the VHF comm. Example - Bendix/King KY 196A: The first IF frequency is 11.4 MHz. The L.O. is above the received frequency (high side injection); therefore, the image frequency is 22.8 MHz above the selected frequency. Set the KY 196A to 120.000 MHz and the TDFM-9300 to 142.8000 MHz. FREQUENCIES RESULTS VHF #1 TDFM-9300 PASS FAIL 135.975 138.0000 121.150 157.5000 131.250 157.5000 118.000 34.000 118.000 45.000 Image: FREQUENCIES RESULTS VHF #2 TDFM-9300 PASS FAIL 135.975 138.0000 121.150 157.5000 131.250 157.5000 118.000 34.000 118.000 45.000 Image: NOTES:

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 27 C. Determine if the image frequency for the VOR/ILS Nav falls within the range of the TDFM-9300. If so, select two sets of frequencies that will cause the TDFM-9300 to be set as close as possible to the image frequency. Choose one set in the localizer frequency range and one in the VOR frequency range. Record those values in the spaces provided in the following chart. Modulate the TDFM-9300 transmitter on the following frequencies for at least 20 seconds. Listen for any noise or detected audio signals on the receiver audio; look for any moment of flags or needles on the navigation display. FREQUENCIES RESULTS VOR/ILS #1 TDFM-9300 PASS FAIL 108.000 162.0000 108.100 162.1500 108.000 36.0000 108.100 36.0325 Image: FREQUENCIES RESULTS VOR/ILS #2 TDFM-9300 PASS FAIL 108.000 162.0000 108.100 162.1500 108.000 36.0000 108.100 36.0325 Image: NOTES:

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 28 D. The following procedure checks for second harmonic interference to the glide slope receiver from the TDFM-9300. All transceivers produce harmonics (multiples of the wanted frequency) and while the TDFM-9300 far exceeds FCC requirements, interference can still be experienced depending upon antenna position and separation. Furthermore, other equipment in the aircraft and the structure of the aircraft can generate harmonics where dissimilar metals make contact or where grounds are isolated, etc. This is also true of aircraft hangars; therefore, testing should be done outside away from any structures where possible. With a portable glide slope generator, provide enough signal to firmly activate the indicator needle and hide all flags. Increase the signal level by 3 dB. Modulate the TDFM-9300 transmitter on the following frequencies for at least 20 seconds. Observe the Glide Slope displays. Look for any movement of flags or needles on the navigation display. If an interference condition is detected, then the installation will have to be flight tested according to the following procedure. Using the table below, determine the glide slope frequency based on the localizer frequency of the ILS to be used. Divide the glide slope frequency by 2 and program into the TDFM-9300. Fly the aircraft to intercept the localizer and glide slope (both needles centered) at 26 nm from the runway. Transmit on the TDFM-9300 for 10 seconds and watch for any deflections or flags. Repeat the test every 2 nm until the indicators are not affected. If the distance is greater than 18 nm, then a pass shall be recorded. Otherwise the TDFM-9300 shall be placarded “Do not transmit while on ILS approach.” Localizer Glide Slope Localizer Glide Slope 108.10 334.70 110.10 334.40 108.15 334.55 110.15 334.25 108.30 334.10 110.30 335.00 108.35 333.95 110.35 334.85 108.50 329.90 110.50 329.60 108.55 329.75 110.55 329.45 108.70 330.50 110.70 330.20 108.75 330.35 110.75 330.05 108.90 329.30 110.90 330.80 108.95 329.15 110.95 330.65 109.10 331.40 111.10 331.70 109.15 331.25 111.15 331.55 109.30 332.00 111.30 332.30 109.35 331.85 111.35 332.15 109.50 332.60 111.50 332.90 109.55 332.35 111.55 332.75 109.70 333.20 111.70 333.50 109.75 333.05 111.75 333.35 109.90 333.80 111.90 331.10 109.95 333.65 111.95 330.95

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 29 FREQUENCIES RESULTS G/S #1 TDFM-9300 PASS FAIL 334.7 (108.1) 167.35 334.7 (108.1) 33.4700 FREQUENCIES RESULTS G/S #2 TDFM-9300 PASS FAIL 334.7 (108.1) 167.35 334.7 (108.1) 33.4700 NOTES: E. Operate the TDFM-9300 transmitter on the following frequency for at least 20 seconds. Observe the Transponder for any spurious replies or loss of reply to test set. NOTES: FREQUENCIES TRANSPONDER #1 TRANSPONDER #2 TDFM-9300 PASS FAIL PASS FAIL 512 MHz 36.0000

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 30 F. Modulate the TDFM-9300 transmitter on the following frequencies for at least 20 seconds. Observe the DME displays. Look for loss of distance information on the display. FREQUENCIES RESULTS DME 1 TDFM-9300 PASS FAIL 978 (108.0) 489 1020 (112.1) 510 FREQUENCIES RESULTS DME 2 TDFM-9300 PASS FAIL 978 (108.0) 489 1020 (112.1) 510 NOTES:

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 31 G. NOTE: For the following tests, select a frequency at the top, middle, and bottom of each band of the TDFM-9300 transceiver. 136 to 174 MHz Band 403 to 470 MHz Band 450 to 512 MHz Band 806 to 870 MHz Band Analog Band Frequency #1 Frequency #2 Frequency #3 H. At a safe altitude, engage the autopilot or stability augmentation system. Modulate the TDFM-9300 transmitter on the above frequencies for at least 20 seconds. Observe any effect on the autopilot or stability augmentation system. Observations: I. Perform a coupled ILS approach to the aircraft's certified limits. Modulate the TDFM- 9300 transmitter on the above frequencies for at least 20 seconds. Observe any effect on the autopilot. Repeat for second flight director/autopilot if equipped. Observations:

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 32 J. List the power plant, fuel and other electric instruments in the chart provided and note any anomalies that occur while transmitting. Assess the results. STEP SYSTEM PASS FAIL NOTES 1 Com 1 & 2 (UHF Lo, UHF Hi, and 800 MHz) 2 Transponder & Encoder (VHF, UHF Lo, and 800 MHz) 3 ADF 1 & 2 4 VG 5 Glideslope 1 & 2 (UHF Lo, UHF Hi, and 800 MHz) 6 VOR/LOC 1 & 2 (UHF Lo, UHF Hi, and 800 MHz) 7 Compass 8 Directional Gyro 9 Fuel Pressure 10 Oil Temp 11 Amps 12 Bus Voltage 13 Fuel % 14 Ng 15 TOT 16 Torque % 17 Annunciators 18 Digital Clock 19 Oil Pressure 20 DME 1 & 2 (VHF, UHF Lo, and 800 MHz) 21 GPS 1 & 2 (UHF Lo and 800 MHz)

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 33 STEP SYSTEM PASS FAIL NOTES NOTES:

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 34 This page is intentionally left blank.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 35 SUPPORT NOTES • For the latest Service Bulletin(s), refer to the Publication Index list under the section for this model (login required). • For the latest Technical Information Bulletins, refer to the Publication Index list under the section for this model (login required). • For the latest Software Release(s), refer to the Publication Index list under the section for this model’s software/firmware history index (login required). NOTES APPENDIX A

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 36 ENVIRONMENTAL QUALIFICATION FORM Model No: TDFM-9300 Part No: 111267-1-93-A10-T5/93037 Description: Airborne Transceiver Manufacturer: Technisonic Industries Limited 240 Traders Blvd., Mississauga, Ontario Canada L4Z 1W7 Tel: 905-890-2113 Fax: 905-890-5338 Tested to: RTCA / DO-160G (December 8, 2010) Date Tested: March 27, 2014 – May 2, 2014 Test Report No: 14RE497 CONDITIONS SECTION CATEGORY COMMENTS Temperature and Altitude 4.0 A2, B1, C4, D1 Low Temperature – Survival 4.5.1 - 55 degrees C Low Temperature – Short Time Operating 4.5.1 - 40 degrees C Low Temperature – Operating 4.5.2 - 30 degrees C High Temperature – Survival 4.5.3 + 85 degrees C High Temperature – Short Time Operating 4.5.3 + 70 degrees C High Temperature – Operating 4.5.4 + 70 degrees C In-Flight Loss of Cooling 4.5.5 not applicable Altitude 4.6.1 50,000 feet Decompression 4.6.2 50,000 feet Overpressure 4.6.3 - 15,000 feet Temperature Variation 5.0 B +/- 5 degrees C per minute Humidity 6.0 X Not tested Operational Shock and Crash Safety 7.0 A Standard Operational Shocks (NOTE-3) Vibration 8.0 S Sinusoidal Vibration – curve M S Random Vibration – curve B U Sine-On-Random Vibration – curve G Explosive Atmosphere 9.0 X Not tested Waterproofness 10.0 X Not tested

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 37 CONDITIONS SECTION CATEGORY COMMENTS Fluids Susceptibility 11.0 X Not tested Sand and Dust 12.0 X Not tested Fungus 13.0 X Not tested Salt Fog Test 14.0 X Not tested Magnetic Effect 15.0 Z Distance result was 0.01 meters Power Input 16.0 B NOTES-2, 3 Voltage Spike 17.0 B NOTE-3 Audio Frequency Susceptibility 18.0 B NOTE-3 Induced Signal Susceptibility 19.0 X Not tested Radio Frequency Susceptibility 20.0 X Not tested Radio Frequency Emission 21.0 M NOTE-1 Lightning Induced Transient Susceptibility 22.0 X Not tested Lightning Direct Effects 23.0 X Not tested Icing 24.0 X Not tested Electrostatic Discharge 25.0 X Not tested Fire, Flammability 26.0 X Flammability – See NOTE-4 Other Tests Remarks: All testing was performed at Technisonic Industries unless otherwise indicated. NOTE-1 Indicated test was performed by ULTRATECH LABS. NOTE-2 Testing included subparagraph 16.6.1.3b: Requirement for Equipment with Digital Circuits. NOTE-3 Approval for this category is based on similarity to the TDFM-9000. See test report 13RE469. NOTE-4 Only applies to units with “MOD 6” marked on the modifications label.

TDFM-9300 Installation Instructions TiL 13RE471 Rev. D Issue 5 38 Technisonic Industries Limited 240 Traders Blvd., Mississauga, ON Canada L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 IMPORTANT WARRANTY All communication equipment manufactured by Technisonic Industries Limited is warranted to be free of defects in Material or Workmanship under normal use for a period of one year from Date of Purchase by the end user. Warranty will only apply to equipment installed by a factory approved and/or authorized facility in accordance with Technisonic published installation instructions. Equipment falling under the following is not covered by warranty: • Equipment that has been repaired or altered in any way as to affect performance • Equipment that has been subject to improper installation • Equipment that has been used for purposes other than intended • Equipment that has been involved in any accident, fire, flood, immersion, or subject to any other abuse. Expressly excluded from this warranty are changes or charges relating to the removal and re-installation of equipment from the aircraft. Technisonic will repair or replace (at Technisonic's discretion) any defective transceiver (or part thereof) found to be faulty during the Warranty Period. Faulty equipment must be returned to Technisonic (or its authorized Warranty Depot) with transportation charges prepaid. Repaired (or replacement) equipment will be returned to the customer with collect freight charges. If the failure of a transceiver occurs within the first 30 days of service, Technisonic will return the repaired or replacement equipment prepaid. Technisonic reserves the right to make changes in design, or additions to, or improvements in its products without obligation to install such additions and improvements in equipment previously manufactured. This Warranty is in lieu of any and all other warranties express or implied, including any warranty of merchantability or fitness, and of all other obligations or liabilities on the part of Technisonic. This Warranty shall not be transferable or assignable to any other persons, firms, or corporations. For warranty registration, please complete the online Warranty Registration Form found at www.til.ca.