Vaxcel T0369 Assembly And Installation Instructions

WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. 1. Thread two headless screws (D) through the cross bar (A), and then secure them with four lock nuts (E). Adjust the length of the headless screws (D) if necessary. Note: Make sure that the headless screws are lined up horizontally to make the fixture level. Note: With silicone caulking compound, caulk completely around where the back plate meets with the wall surface to prevent water from seeping into outlet box. 2. Attach the cross bar (A) to the outlet box by using two mounting screws (B). 3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (F) as follows: ---Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source. ---Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source. ---Attach the fixture grounding wire (usually green insulation or bare wire) to the cross bar (A) with the green grounding screw (C), and then connect it to the house grounding wire with the wire connector (F). Carefully put the wires back into the outlet box. 4. Attach the fixture to the cross bar (A) by inserting headless screws (D) into holes on back plate, and then secure it with two rubber pads (H) and two ball nuts (G). ASSEMBLY AND INSTALLATION INSTRUCTIONS T0369 T0372 T0484 T0488 Mounting Screw (B) Wire Connector (F) Ball Nut (G) Rubber Pad (H) Cross Bar (A) Hardware Package (included): Green Grounding Screw (C) Turn off the power at fuse or circuit box. Installation Steps IMPORTANT: The sensor has an excellent photocell function to enable the light to turn on at dusk and off at dawn automatically. Headless Screw (D) Shade Green Grounding Screw (C) Outlet Box Wire Connector (F) Headless Screw (D) Cross Bar (A) Lock Nut (E) House Grounding Wire Fixture Grounding Wire Fixture Wire Bulb Type A Max.60W (not included) Fixture Mounting Screw (B) Holder Socket Socket Ring Photocell Back Plate Ball Nut (G) Rubber Pad (H)

6. Install a bulb (not included). Check relamping label at socket area or packaging for maximum allowed wattage. Turn on the power at fuse or circuit box. Turn on the power at fuse or circuit box. A: 15" B: 12.25" C: 23" The following parts are available for re-order if damaged or missing. Spare Parts List: 1. Turn off the power at the fuse or circuit box before starting installation. 2. Loosen the wire connector connected with the wires from photocell. (See Fig.1) Note: Do not move the photocell to prevent water from seeping into the outlet box. 3. Take a white pigtail and black pigtail and make wire connections using wire connectors (F) : (See Fig.2) a. The black wire from the fixture to one end of the black pigtail. b. The white wire from the fixture to one end of the white pigtail. c. The other end of the black pigtail to the black wire from the power source. d. The other end of the white pigtail to the white wire from the power source. Put all wires back into the back plate of the fixture. Operation the Unit Without Photocell Photocell White Wires From Photocell Wire Connector Wires From Fixture Wires From Fixture Wires From Main Power Wire Connector (F) White Pigtail Pigtail Red Wires From Photocell Black Wires From Photocell Fig.1 Fig.2 Mounting Screw (B) Rubber Pad (H) Cross Bar (A) Green Grounding Screw (C) Lock Nut (E) Wire Connector (F) Ball Nut (G) Headless Screw (D) A B C Assembly Kit 5786MM (1 SET) for T0369 5787MM (1 SET) for T0372 5987MM (1 SET) for T0484 5988MM (1 SET) for T0488