Teac TTDEDS2018D Operation & User’s Manual

www.teac.com.au IMPORTANT ! Trademark of TEAC Corporation JAPAN Stereo Turntable with Bluetooth Input TTDEDS2018D

2 – Speaker 3 – Power on/off switch & volume button 4 – Anti-slip foot 5 – Adaptor - Use it when playing 45rpm records with cut out centre. 6 – Tone arm/Also switch for BT. When the Tone arm is placed on Tone arm holder, the turntable will change to Bluetooth mode. 7 – Tone arm lift lever 8 – On / OFF Phono play Function selection. 9 – Speed selection - Three speeds available: 33.3, 45, 78 rpm 10 – Turntable plate 11 – Ceramic cartridge with diamond needle 12 – RCA out jack 13 – DC in power jack PRODUCT DESCRIPTION 6 7 8 9 10 11 5 1 2 3 4 13 12

unit. Your unit is ready to be connected to a mains voltage of 220V-240V/50Hz. AMPLIFIER CONNECTION Whilst you can listen to your new turntable using the built-in speakers, you may wish to connect it to your existing Hi Fi system. Connect the audio plugs to the AUX input on your mixer or amplifier using an RCA cable (not supplied). y y Red plug into R/H channel input. y y White plug into L/H channel input. Playing a record yy Place the record on the turntable. If required, do not forget to place the adaptor on the record spindle. yy Choose the desired playing speed using the speed selection switch between 33.3, 45 and 78rpm. yy Turn on the Rotary Power Switch, note that this also controls volume. yy Release the tone arm lock. yy Raise the arm with your hand lightly. yy Place the stylus vertically over the first track of the record, the turntable will start turning automatically. yy Lower the stylus slowly onto the record to play. yy When a record comes to the end, the turntable will stop automatically if the auto-stop switch is in the ON position. If the switch is in the off position then it will keep revolving until the tone arm is returned to the tone arm rest. yy Lift up the tone arm and put it on the rest when finished. yy Replace the protective cap on the stylus and close the tone arm lock. yy Turn off the power at mains. Connect to Bluetooth devices Play from Bluetooth device: 1. Turn the AUTO STOP ON/OFF to “ON”. 2. Put the tonearm at the rest position. Then you will hear a beep sound. 3. Then, activate the Bluetooth function in your Bluetooth device (such as Mobile Phone or tablet). The device will begin to automatically search for available nearby Bluetooth devices to pair with. 4. Once the turntable is detected, your Bluetooth device will show “TTDEDS2018D” on the list of nearby devices. Select it for pairing. Wait a few seconds and your Bluetooth device will list it as connected. 5. Now you can start to play music on your Bluetooth device.

interference, moving beyond the maximum connection distance, or having an object move between both Bluetooth devices. However, your device will usually reconnect again automatically. In some cases, the devices may need to be manually reconnected using the Bluetooth device’s settings. 2. If you cannot connect your Bluetooth device, the Bluetooth driver may need to be updated to the latest version. DISCONNECTED FROM PAIRED DEVICE 1. To disconnect with a paired device, Turn OFF the system directly. 2. You can also disconnect from the Bluetooth device manually - turn OFF the Bluetooth function from the paired device to disconnect from the turntable. CONNECT TO NEW BLUETOOTH DEVICE Turn off the Bluetooth function from the previous Bluetooth device. If the system is disconnected from the paired device, the system will generate a beep sound every few seconds as a prompt for action. Follow the previous pairing steps to connect to a new Bluetooth device of choice. MAINTENANCE REPLACING THE STYLUS -Refer to the figures 1-8

sound and ensure they are long lasting. 2. For best playback results, it is recommended to replace your stylus periodically (approximately every 250 hours). 3. Dust the stylus from time to time using a very soft brush dipped in alcohol (brushing from back to front of the cartridge) 4. WHEN TRANSPORTING YOUR RECORD PLAYER, DO NOT FORGET TO: Replace the protective cap on the stylus. Put the rest clip into the pick-up arm. 5. Only store and operate this turntable in a dry and well-ventilated environment. 6. Do not place naked flame sources, such as lit candles on or near the device. 7. Do not expose the turntable to dripping or splashing water. PRODUCT SPECIFICATIONS • Belt Drive Turntable with DC Motor • 3 Speed Turntable – 33⅓, 45, 78 RPM • Plays 7”, 10”and 12”records • Bluetooth Input • Built-in stereo speakers - 4Ω, 3W x 2 • Line out to connect to amplifier • Unit dimensions: 379 x 163 x 330mm • Unit weight: 2.25 kg • Output power: 7W

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. 1. TEAC warrants that this product is free from defects in material and workmanship under normal domestic use with reasonable care and skill. Maintenance and cleaning (i.e. laser head) is not covered by this warranty. The TEAC warranty only applies to TEAC products purchased NEW from a TEAC Authorised Retailer in Australia. This warranty only applies to the original purchaser and cannot be transferred. 2. The benefits to the consumer given by this Warranty are in addition to other rights and remedies of the consumer under a law in relation to goods or services to which the warranty relates, being the Australian Consumer Law. 3. Refund or replacement via your TEAC Authorised Retailer is available for a period of 14 days after purchase for goods that have been inspected and determined to have a major failure. Refund and exchange is not applicable for change of mind. 4. Subject to the terms herein, this warranty effectively covers TEAC products under the 12 Month Replacement Warranty Scheme, 12 months from the date of original purchase. 5. The warranty is void and warranty claims may be refused, subject to the Australian Consumer Law, if: a) The product was not transported, installed, operated or maintained according to manufacturer instruction, or b) The product was abused, damaged, tampered, altered or repaired by any unauthorised persons, or c) Product failure is due to accidents during use, installation or transit, power surges, use of defective or incompatible external devices, exposure to abnormal conditions such as excessive temperatures or humidity, or entry of liquids, objects or creatures into the product, cockroach infestations, or d) The customer is unable to provide proof of purchase of the product for verification, or e) The serial number of the product is missing or has been tampered with. 6. No one is authorised to assume any liability on behalf of TEAC or impose any obligation on it, in connection with the sale of any equipment other than as stated in this warranty and outlined above. 7. TEAC and/or its Authorised Service Centres reserve the right to inspect and verify whether the product is exhibiting a major failure as claimed by customers/retailers.

AEST *Please have your purchase receipt and the product's serial number ready For other enquiries and support please visit www.teac.com.au TEAC Warranty Service Hotline 1300 553 315