Reliable MBEC-14 Bulletin

Model MBEC-14 Extended Coverage Ordinary & Extra Hazard Horizontal Sidewall Sprinklers for Metal Building Applications Bulletin 169 Rev. F Bulletin 169 Rev. F Model MBEC-14 (SIN R6932) Features 1. Designed to be installed on piping that is sup- ported by the primary structure, not the purlins. 2. Provides Extended Coverage Ordinary & Extra Hazard protection to 175 ft2 (16.3m2) per sprinkler. 3. Very extra large orifice of nominal K =14 (200) permits low pressures. 4. Density/Area Demand based upon hazard to be protected. 5. 165°F (74°C) & 212°F (100°C) temperature rat- ings. 6. Standard finishes in brass and chrome. 7. Can be used for all editions of NFPA 13 that per- mit extended coverage sprinklers. Listings & Approvals 1. Listed by Underwriters Laboratories, Inc. and UL Certified for Canada (cULus). 2. Certified by FM Approvals FM Global considers this sprinkler as a “Quick Response” extended coverage sprinkler. 3. NYC MEA 258-93-E UL Listing Category Sprinklers for Storage Protection (Specific Application) UL Guide Number VNIV Patents: US Patent No. 6,889,774 B2 Product Description The Reliable MBEC-14 Extended Coverage Sprinkler is a special application sprinkler for the protection of metal buildings with purlin roof support. The sprinkler has a very extra large orifice, Nominal K=14 (200). When the system is designed to NFPA 13 requirements, MBEC-14 sprinklers provide protection in Ordinary Hazard (Groups 1 and 2) and Extra Hazard (Groups 1 and 2) Occupan- cies to 175 ft2 (16.3 m2) per sprinkler . For FM Global, use Table 2 of FM Global Data Sheet 3-26 for nonstorage occupancies. FM does not permit the use of these sprinklers in areas with flammable liquids or shielded discharge. FM Global representatives must be contacted for exact require- ments. Reliable MBEC-14 sprinklers are to be installed accord- ing to the design criteria shown in this bulletin. Figure 3 shows a suggested method of installing the line piping. Reliable MBEC-14 sprinklers use a levered fusible alloy solder link. Design Criteria Reliable Model MBEC-14 sprinklers are to be used in systems designed and installed in accordance with NFPA 13, FM Global requirements and all other local codes and ordinances. The following design criteria also apply: • Design Density/Area method sprinkler. Minimum End- head Pressure: 7.0 psi (0.5 bar) Minimum density: 0.21 GPM/ft2 (8.56 Lpm/m2). • Maximum building height at peak is 32’ (9.8 m). Maximum protected bay width is 25’ (7.6 m). See Figures 1. & 2. • Sprinklers may be installed on pipe lines attached to the top flange of primary roof beams. Sprinklers are to be in- stalled with deflectors parallel to the floor. See Figure 2. • Maximum sprinkler spacing along the pipe is 14’ (4.3 m) and maximum water discharge length from the pipe is 12.5’ (3.8 m). 175 ft2 is the maximum coverage area. See Figures 2 & 3. • Minimum sprinkler spacing is 7’ (2.1 m) for NFPA and 8’ for FM Global. (This does not apply to back-to-back sprin- klers separated by the I-beams.) See Figures 2, 3 & 4. • Deflector to commodity clearance shall be a minimum of 10’ (3.1m). See Figures 2 & 3. • Miscellaneous and in-process storage of 12’ (3.7 m) for NFPA applications and 10’ for FM Global is permitted. • Deflector distance below roof/ceiling is 12” (305 mm) to 16” (406 mm). If there is an interior liner panel installed on the bottom side of the roof purlins, the acceptable deflec- tor distance is 4”- 6” below the liner panel. See Figure 3. • Follow NFPA 13 requirements for obstructions to sprinkler’s discharge (Extended Coverage Sidewall Spray Sprin- klers). • Sprinklers can be installed under a sloping ceiling not ex- ceeding 2” (50.8 mm) of rise in 12” (305 mm) of run. • Maximum working pressure is 175 psi (12 bar) at the sprinkler. • Available for use in wet, dry, or preaction systems.

25ft. (7.6m) 175ft.2 (16.3m2) cULus FM NYC R6932 212 100 150 66 Maintenance Model MBEC-14 Sprinklers should be inspected and the sprinkler system maintained in accordance with NFPA 25. Do not clean sprinklers with soap and water, ammonia or any other cleaning fluids. Remove dust by using a soft brush or gentle vacuuming. Remove any sprinkler that has been painted (other than factory applied) or damaged in any way. A stock of spare sprinklers should be maintained to allow quick replacement of damaged or operated sprinklers. Prior to installation, sprinklers should be maintained in the original cartons and packaging un- til used to minimize the potential for damage to sprinklers that would cause improper operation or non-operation. Model MBEC-14 Sprinkler Specifi cation Sprinklers shall be a control-mode, standard response, ex- tended coverage horizontal sidewall sprinkler specifically listed/ approved for installation on primary structural members (I- beams) of pre-engineered metal buildings, up to 32 ft (9.8 m) in height and having 25 ft. (7.6 m) wide bays. Sprinklers shall be [(cULus Listed) (New York City MEA Approved, 258-93-E) to protect ordinary and extra hazard] [FM Approved to protect ordinary hazard] occupancies as well as for miscellaneous and in-process storage as permitted by [NFPA 13] [FM Global Data Sheet 3-26]. Sprinklers shall be capable of covering an area of 175 ft2 and being installed below the ceiling between 12” (305 mm) and 16” (406 mm). If there is an interior liner panel installed on the bottom side of the roof purlins, the acceptable deflector distance is 4”- 6” below the liner panel. Roof/ceilings shall have slopes not exceeding a pitch of 2/12 (a roof /ceiling slope of 16.7%). Sprinkler frame and deflector to be of bronze construc- tion. Fusible solder link assembly shall utilize the strut and lever principle of operation with a [black-painted, 165°F (74°C)] [gray- painted 212°F (100°C)] beryllium-nickel thermal element. Water seal assembly shall consist of a Teflon™-coated Bellville spring washer and brass cap assembly containing no plastic parts. Extended coverage horizontal sidewall sprinklers shall have a nominal K-factor of 14.0 (202) and ¾” NPT threaded end con- nections. Sprinkler temperature rating shall be [Ordinary 165°F (74°C)] [Intermediate 212°F (100°C)]. Extended coverage hori- zontal sidewall sprinklers shall be Reliable Model MBEC-14, SIN R6932 (Bulletin 169). Ordering Information Specify: 1. Sprinkler Model 2. Temperature Rating 3. Sprinkler Finish Finishes(1) Standard Finishes Bronze Chrome Plated (1) Other colors and finishes are available on special order. Consult factory for details. Model H Sprinkler Wrench Use Model H Wrench for Model MBEC-14 HSW Sprinkler removal and installation.

(800) 431-1588 Sales Offices (800) 848-6051 Sales Fax (914) 829-2042 Corporate Offices www.reliablesprinkler.com Internet Address Manufactured by Recycled Paper Revision lines indicate updated or new data. EG. Printed in U.S.A. 10/13 P/N 9999970234 The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable. Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries. • Automatic sprinklers • Flush automatic sprinklers • Recessed automatic sprinklers • Concealed automatic sprinklers • Adjustable automatic sprinklers • Dry automatic sprinklers • Intermediate level sprinklers • Open sprinklers • Spray nozzles • Alarm valves • Retarding chambers • Dry pipe valves • Accelerators for dry pipe valves • Mechanical sprinkler alarms • Electrical sprinkler alarm switches • Water flow detectors • Deluge valves • Detector check valves • Check valves • Electrical systems • Sprinkler emergency cabinets • Sprinkler wrenches • Sprinkler escutcheons and guards • Inspectors test connections • Sight drains • Ball drips and drum drips • Control valve seals • Air maintenance devices • Air compressors • Pressure gauges • Identification signs • Fire department connection Reliable offers a wide selection of sprinkler components. Following are some of the many precision-made Reliable products that guard life and property from fire around the clock. Reliable...For Complete Protection