REED R6010 Instruction Manual

Pantone 485 Red - 10/100/100/5 Pantone 123 Yellow - 0/27/100/ www.reedinstruments.com 1-877-849-2127 | [email protected]

Pantone 123 Yellow Pantone 485 Red Pantone 123 Yellow Pantone 534 Blue Black Rich Black - 20/20/20/100 Blue - 100/80/30/5 Yellow - 0/27/100/0 Red - 10/100/100/5 Yellow - 0/27/100/0 Blue - 100/80/30/5 Only if you REALLY need them: Pantone 534 Blue - 100/80/30/5 Pantone 485 Red - 10/100/100/5 Pantone 123 Yellow - 0/27/100/ Table of Contents Features..........................................................................................3 Specifications.................................................................................3 Instrument Description...................................................................4 Operating Instructions....................................................................5 Taking a Measurement.................................................................5 Alarm Set Mode...........................................................................5 Backlighting.................................................................................5 Moisture Table of Comparison.......................................................6 Notes..............................................................................................6 For service on this or any other REED product or information on other REED products, contact REED Instruments at [email protected] www.reedinstruments.com 1-877-849-2127 | [email protected]

Pantone 123 Yellow Pantone 485 Red Pantone 123 Yellow Pantone 534 Blue Black Rich Black - 20/20/20/100 Blue - 100/80/30/5 Yellow - 0/27/100/0 Red - 10/100/100/5 Yellow - 0/27/100/0 Blue - 100/80/30/5 Only if you REALLY need them: Pantone 534 Blue - 100/80/30/5 Pantone 485 Red - 10/100/100/5 Pantone 123 Yellow - 0/27/100/ Features • Detects moisture content in building materials of all kinds, as well as detects moisture distribution in walls, ceilings and floors • Non-destructive - moisture sensor runs smoothly over the surface being tested without scratching or penetrating the surface • Classifies moisture status as: dry, at risk or wet • Display Hold button • Max/Min function with alarm indication • LCD display with backlighting • Low battery indication with auto power off Specifications Measuring Range: 0.0 to 100.0% Moisture Content Resolution: 0.1% M.C. Penetration Depth: 20 to 40mm Power Supply: 3 x “AAA” batteries Dimensions: 242 x 63 x 30mm Weight: 226g Optional Accessories: Soft Carrying Case (Model CA-05A) www.reedinstruments.com 1-877-849-2127 | [email protected]

Pantone 123 Yellow Pantone 485 Red Pantone 123 Yellow Pantone 534 Blue Black Rich Black - 20/20/20/100 Blue - 100/80/30/5 Yellow - 0/27/100/0 Red - 10/100/100/5 Yellow - 0/27/100/0 Blue - 100/80/30/5 Only if you REALLY need them: Pantone 534 Blue - 100/80/30/5 Pantone 485 Red - 10/100/100/5 Pantone 123 Yellow - 0/27/100/ Instrument Description 1. Moisture sensor 2. LCD display 3. MEAS button 4. UP/Backlighting button 5. Alarm SET button 6. DOWN button 7. ON/OFF button 8. Battery cover Display Description 1. Low Battery indicator 2. Data Hold symbol 3. Current moisture value 4. DRY symbol 5. RISK symbol 6. WET symbol 7. MAX symbol 8. MAX moisture value 9. MIN symbol 10. MIN moisture value www.reedinstruments.com 1-877-849-2127 | [email protected]

Pantone 123 Yellow Pantone 485 Red Pantone 123 Yellow Pantone 534 Blue Black Rich Black - 20/20/20/100 Blue - 100/80/30/5 Yellow - 0/27/100/0 Red - 10/100/100/5 Yellow - 0/27/100/0 Blue - 100/80/30/5 Only if you REALLY need them: Pantone 534 Blue - 100/80/30/5 Pantone 485 Red - 10/100/100/5 Pantone 123 Yellow - 0/27/100/ Operating Instructions Taking a Measurement Turn the meter ON by pressing the button. Hold the meter in a upright position so the ball sensor is in the air and at least 8-10cm away from any object. Press the MEAS button and “CAL” will display on the LCD screen. The value must be below 0.5 to be able to take accurate measurements. If the reading is above 0.5 you must turn the meter off and move to a dry area to calibrate. After the meter is calibrated it will automatically start to take measurements. To hold the current measurement press the MEAS . button and the data hold symbol will appear on the LCD screen. . After 30 seconds of inactivity the meter will auto power off. Note: When you move from the location of your initial calibration you must re-calibrate the meter Alarm Set Mode To change the RISK and WET alarm value turn on and calibrate the meter. Press the MEAS button to put the meter in data hold and press the SET button. The RISK symbol will appear on the LCD screen and the value which the RISK alarm is set to. To change the alarm value press the UP or DOWN buttons. Press the SET button to save your setting and to change the WET alarm value. The WET symbol will appear on the screen beside the WET alarm value. To change the WET alarm value press the UP or DOWN buttons. Press the SET button to save the WET alarm value and to return to data hold mode. If the moisture measurement exceeds the RISK alarm setting the meter will beep every second. If the moisture measurement exceeds the WET alarm setting the meter will beep every half second. Note: The RISK alarm value is between 0-50. The default setting is 30 The WET alarm value is between 50-100. The default setting is 60 Backlighting When the meter is in data hold, press the UP button to turn the backlighting on or off. www.reedinstruments.com 1-877-849-2127 | [email protected]

Pantone 123 Yellow Pantone 485 Red Pantone 123 Yellow Pantone 534 Blue Black Rich Black - 20/20/20/100 Blue - 100/80/30/5 Yellow - 0/27/100/0 Red - 10/100/100/5 Yellow - 0/27/100/0 Blue - 100/80/30/5 Only if you REALLY need them: Pantone 534 Blue - 100/80/30/5 Pantone 485 Red - 10/100/100/5 Pantone 123 Yellow - 0/27/100/ Moisture Table of Comparison Construction Material Display (Unit) Moisture Status Gypsum <30 DRY 30-60 RISK >60 WET Cement <25 DRY 25-50 RISK >50 WET Wood <50 DRY 50-80 RISK >80 WET Notes: • Be sure to maintain a minimum distance of 8-10cm from corner areas as to not take in conflicting values • The moisture sensor ball head must be kept perpendicular to the ma- terial being measured, pressed firmly on the surface and not slanted • If the thickness of the material being measured is less than 20mm the reading may not be accurate due to conflicting values • If the BAT symbol appears on the LCD screen, the batteries need to be replaced For service on this or any other REED product or information on other REED products, contact REED Instruments at [email protected] www.reedinstruments.com 1-877-849-2127 | [email protected]