METRON PC03 Operation & User’s Manual

PC03, PC04 AND PC05 GET STARTED METRON EV portable chargers PC03, PC04 and PC05 are designed to charge electric vehicles equipped with Type 2 charging sockets (European standard) from any standard household outlet (e.g. Schuko) or industrial socket (e.g. 1 or 3-phase CEE sockets). Where’s the in-line “bulky box”? Metron portable chargers are truly unique because all the charging station electronics is placed inside Type 2 charging plug itself! First plug the portable charger in the wall outlet. Immediately signal LED starts blinking: number of blinks tells you what is the saved power setting (see the next page). Afterwards LED glows constantly till AC power is present indicating standby/ready status. The biggest advantage of this design is the fact that METRON portable chargers don’t have that heavy in-line “bulky box” as others do, what makes them lighter, easier to install/connect and also easier to store in a carrier case. METRON portable chargers also offer the possibility to set desired charging current/power by simply pressing a button. When you plug it into the vehicle Type 2 socket it starts blinking slowly which means the vehicle is charging. When your electric vehicle is fully charged the LED glows constantly again. 1 USER MANUAL EV PORTABLE CHARGERS

Number of LED blinks 1 6 A / 1,4 kW 2 8 A / 1,8 kW 3 10 A / 2,3 kW 4 13A / 3,0 kW 5 16A / 3,7 kW Number of LED blinks 1 6 A / 1,4 kW 2 8 A / 1,8 kW 3 10 A / 2,3 kW 4 13A / 3,0 kW 5 16A / 3,7 kW 6 20A / 4,6 kW 7 25A / 5,8 kW 8 32A / 7,4 kW Number of LED blinks 1 3 x 6 A / 4,1 kW 2 3 x 8 A / 5,5 kW 3 3 x 10 A / 6,9 kW 4 3 x 13A / 9,0 kW 5 3 x 16A / 11,0 kW PC05 PC04 PC03 Push Button LED light New charging current/power setting is stored in the memory and it stays the same (even after the power supply is not present anymore) until the next setting change is performed. SETTING THE DESIRED CHARGING CURRENT/POWER METRON portable chargers allow user to set desired charging current/power, before being plugged in the electric vehicle Type 2 socket, or even while the vehicle is charging! Procedure is simple: • press and hold the push button: LED switches off immediately • after 5 seconds LED starts blinking slowly • Releasing the push button after a certain number of blinks determines charging current/power as follows: Charging current/power Charging current/power Charging current/power STATUS NOTIFICATION BY LED BLINKS LED STATUS NOTIFICATION Slow blinking when power supply is applied Constantly on when not plugged in Slow blinking when plugged in Constantly on when plugged in Indicating previous saved current setting Stand-by / Ready to charge Charging Electric vehicle fully charged

or 1-phase 16A CEE “camper” socket if proper adaptor is used. In such case PC05 behaves like PC03 portable charger (same current/power). 1-phase portable charger PC04 can also charge from domestic 1-phase wall socket (Schuko) or 1-phase 16A CEE “camper” socket if proper adaptor is used. In such case be sure to set charging current to 16A or less, otherwise you risk damage to the socket or even blown fuse! The use of portable charger versions without RCD protection is allowed exclusively on the installations, protected by RCD. Household 16A Schuko wall sockets must be designed for constant 16A current! In the event the cable has been damaged the product should be removed from use immediately! Type 2 (IEC 62196) Female Plug Type 2 (IEC 62196) Female Plug Type 2 (IEC 62196) Female Plug Schuko – Type F/E, CEE, Type G, Type H, … CEE 32A (3-phase/3P+N+E), CEE 32A (1-phase/2P+E), … CEE 16A (3-phase/3P+N+E), CEE 32A (3-phase/3P+N+E) 16A (1-phase) 32A (1-phase) 3x16A (3-phase) or 1x16A (1-phase) 6/8/10/13/16 A 6/8/10/13/16/20/25/32 A 6/8/10/13/16 A 3,7 kW 7,4 kW 3,7 kW (1-phase) 11 kW (3-phase) 230 Vac (1-phase) 230 Vac (1-phase) 230 Vac (1-phase) 400 Vac (3-phase) from 90 V to 270 V (50/60 Hz) from 90 V to 270 V (50/60 Hz) 90 V to 270 V (1- phase) 155 V to 470 V (3-phase) (50/60 Hz) optional (Schuko only) no no yes yes yes 5m to 12m (or on request) 5m to 12m (or on request) 5m to 12m (or on request) optional no no no optional optional yes (all parts) yes (all parts) yes (all parts) from -30°C to +50°C from -30°C to +50°C from -30°C to +50°C IP54 (rain water resistant) IP54 (rain water resistant) IP54 (rain water resistant) 1.6 kg (5m cable) + 0.16 kg per each additional meter of cable 2.3 kg (5m cable) + 0.3 kg per each additional meter of cable 1.9 kg (5m cable) + 0.22 kg per each additional meter of cable PC04 PC05 PC03 Electric vehicle requests room ventilation (no charging) Portable charger overheated (no charging); restarts charging automatically when it cools down Wall plug overheated (no charging); restarts charging automatically when it cools down; applies only to versions with wall plug integrated over-tem perature protection Slow blinking 3 times (plugged in or not plugged in) Slow blinking 5 times (plugged in or not plugged in) Rapid blinking (plugged in or not plugged in) Fault Slow blinking 2 times when plugged in TECHNICAL SPECIFICATIONS EV Side Plug Type Wall socket/grid side Standard Plug Types Max. Charging Current Possible charging current settings Max. Charging Power Rated Voltage Operating voltage/ frequency range Wall plug integrated OVER-TEMPERATURE PROTECTION with automatic reset PREMIUM quality cable (German Technology) Cable length Type A ground fault protection device (RCD) Type B ground fault protection device (RCD) UV resistance Operating Ambient Air Temperature Range IP Rating Weight

as PC03xyz, PC04xyz and PC05xyz, where “x” and “y” and “z” may be any alphanumeric character or blank, representing a color or wall plug type, or lower than standard charging current limit or factory version, or any possible future product differentiations, which do not have an impact on general technical specifications. RCD is an acronym for Residual Current Device - sometimes it can be called also Earth Leakage Circuit Breaker or Safety Switch. Its purpose is to prevent you from getting a fatal electric shock if you touch live part, such as a bare copper wire under high voltage. RCDs offer a level of personal protection that ordinary fuses/circuit-breakers cannot provide. RCD constantly monitors the electric current flowing through one or more circuits which it protects. If it detects electricity flowing down an unintended path, such as through a person who has touched a live part, the RCD will switch the circuit off very quickly, significantly reducing the risk of death or serious injury. To start charging press “RESET” button on RCD. Green LED should turn on. Rev. 4 4/2019 4 LED light WHAT IS RCD AND HOW DOES IT WORK? LIMITED WARRANTY METRON warrants its product to the original consumer purchaser that it will repair, or replace, any product that is determined to be defective for the following terms: One (1) year from date of purchase on all components. To be eligible for repair or replacement under this warranty, the product in question must be sent back to METRON within the warranty period and the original consumer purchaser must comply with the following conditions: • The product thereof must not have been modified or altered in any way by an unauthorized source. • The product thereof must have been used in accordance with the user manual. This limited warranty does not cover: • Damage due to improper use; • Accidental or intentional damage; • Misuse, abuse, corrosion, or neglect; • Product impaired by severe natural conditions, such as excessive hail storms, lightning strikes, tornados, flooding, ice or other natural occurrences; • Damage due to improper packaging on return shipment. Any and all labor charges for troubleshooting, removal or replacement of the product are not covered by this warranty and will not be honored by METRON. All shipping costs regarding repair or replacement of the product is to be pre-paid by the original consumer purchaser.