Mercia Garden Products 0628LOG171-V4 General Instructions Manual

Step 7 (See Pre-Assembly) Parts needed - No. 6 QTY 12 No. 7 QTY 6 No. 8 QTY 12 No. 9 QTY 2 Following the same method outlined in Pre-Assembly, lay the remaining boards (No’s. 6, 7, 8 & 9) onto the assembly to bring the board level to the top of the window and door frames. *Ensure that the boards are level and fush with each other as you lay each one. IMPORTANT: Pre-drill before fxing screws. Step 6 Parts needed - No. 1 QTY 1 Ensure that the lip of the window frame is located on the inside of the building . ...

23b 11 11 11 Step 11 Parts needed - No. 11 QTY 48 Place the frst two roof board’s (No. 11) onto the assembly on each side, making sure the boards are fush to the end of the roof purlin. Once in position fx to each purlin using 3x40mm screws. *Ensure the roof boards meet at the top of the apex and leave an over- hang at the bottom. Due to natural occurences of wood shrinkage / expansion. You maybe required to use the provided spac- ers and place a space of 2mm to ensure every roof board lines up with the truss’. Continue addi ...

70mm Screw x56 Pre-assembly *Please note: Each board interlocks at either end in a staggered pattern. Before securing ensure that the boards are ftted properly in their respective tongues and grooves. Nail Bag 40mm Screw x398 30mm Screw x78 P 3 Please retain product label and instructions for future reference 70mm Bolt Set x16 ...

23b 11 11 11 Step 11 Parts needed - No. 11 QTY 48 Place the frst two roof board’s (No. 11) onto the assembly on each side, making sure the boards are fush to the end of the roof purlin. Once in position fx to each purlin using 3x40mm screws. *Ensure the roof boards meet at the top of the apex and leave an over- hang at the bottom. Due to natural occurences of wood shrinkage / expansion. You maybe required to use the provided spac- ers and place a space of 2mm to ensure every roof board lines up with the truss’. Continue addi ...

23b 11 11 11 Step 11 Parts needed - No. 11 QTY 48 Place the frst two roof board’s (No. 11) onto the assembly on each side, making sure the boards are fush to the end of the roof purlin. Once in position fx to each purlin using 3x40mm screws. *Ensure the roof boards meet at the top of the apex and leave an over- hang at the bottom. Due to natural occurences of wood shrinkage / expansion. You maybe required to use the provided spac- ers and place a space of 2mm to ensure every roof board lines up with the truss’. Continue addi ...

23b 11 11 11 Step 11 Parts needed - No. 11 QTY 48 Place the frst two roof board’s (No. 11) onto the assembly on each side, making sure the boards are fush to the end of the roof purlin. Once in position fx to each purlin using 3x40mm screws. *Ensure the roof boards meet at the top of the apex and leave an over- hang at the bottom. Due to natural occurences of wood shrinkage / expansion. You maybe required to use the provided spac- ers and place a space of 2mm to ensure every roof board lines up with the truss’. Continue addi ...

HANDLE WITH CARE 1 2 3 4 Felt tacks Step 16 Parts needed - No. 20 Cut the felt into fve strips and lay onto the roof in the order shown in the illustration. *Ensure there is approximately 50mm of overhanging felt each side. Once the felt is laid out fx to the roof using felt tacks at 100mm intervals. *Felt size: 2732mm 170x Felt Tacks 1. 2. 3. 4. 5. 13 13 13 13 Step 17 Parts needed - No. 13 QTY 4 Align the fascia’s (No. 13) with the roof and fx into place using 3x40mm screws per fascia, making to screw through the fascia into ...