iStorage diskAshur2 Quick Start Manual

plug into a powered USB port. The LEDs will go through 3 test stages, blinking in sequence RED, GREEN and BLUE, followed by two GREEN blinks and then to RED (Standby State) on a successful test. Any test failure will force the diskAshur2 to securely reset itself and automatically resume the self-test without affecting the security characteristics or any data stored on the drive. To unlock the diskAshur2 for the first time with the default Admin PIN, insert the integrated USB 3.1 cable to a powered USB port and follow the instructions in the table below. PIN Requirement • PINs must be a minimum length of 7 and maximum 15 digits. • Cannot contain all sequenital numbers (2345678 or 9876543). • Cannot contain all repeating numbers (1111111). • The SHIFT key can be used for additional combinations (e.g. SHIFT+1 is a separate value to just 1). First Time Use QUICK START GUIDE LOCK SHIFT UNLOCK LED LIGHTS Thank you for purchasing the iStorage diskAshur2. Your diskAshur2 is preformatted in NTFS and shipped with a default Admin PIN of 11223344 and although it can be used straight out of the box with the default Admin PIN, for security reasons, we highly that a new Admin PIN be created immediately by following the instructions under the heading ‘Changing the Admin PIN’. 1. In Standby State (solid RED LED), enter the default Admin PIN ‘11223344’ and then press the ‘UNLOCK’ button GREEN and BLUE LEDs will alternately blink several times and then to a solid BLUE LED changing to a blinking GREEN and finally to a solid GREEN LED Note: Once the diskAshur2 has been successfully unlocked, the GREEN LED will remain on and in a solid state. It can be locked down immediately by pressing the ‘LOCK’ button once or by (strongly recommended) clicking the ‘Safely Remove Hardware/Eject’ icon within your operating system. - Standby State/Locked - User Mode/Unlocked - Admin Mode Desk Lock Slot Connection Alphanumeric Keypad Integrated USB 3.1 Cable

Unlocking with either the Admin or User PIN Unlock with Admin PIN ( PIN + ) 1. To unlock the diskAshur2 as Admin, enter your Admin PIN and then press the ‘UNLOCK’ button. GREEN and BLUE LEDs will alternately blink several times and finally changing to a solid GREEN LED indicating the drive is unlocked and ready to use as Admin. Unlock with User PIN ( + PIN + ) 2. To unlock the diskAshur2 as the User, press the ‘UNLOCK’ button, all LEDs will blink on and off, then enter your User PIN and press the ‘UNLOCK’ button again. GREEN and BLUE LEDs will alternately blink several times and finally changing to a solid GREEN LED indicating the drive is unlocked and ready to use as the User. For more features and detailed instructions please refer to the user manual pre-loaded on your new diskAshur2 and also available on our website. iStorage provides the following helpful resources: • iStorage Website (https://istorage-uk.com). Check for up-to-date information. • E-mail us at [email protected] • Call the Technical Support Department at +44 (0) 20 8991 6260 • iStorage’s Technical Support Specialists are available from 9:00 a.m to 5:30 p.m GMT, Mon- Fri. Changing the Admin PIN To change the Admin PIN to your own unique 7-15 digit PIN, follow the steps below. Adding a New User PIN in addition to the Admin PIN 1. In Standby State (solid RED LED), press and hold down both the ‘UNLOCK and number ’1’ buttons Solid RED LED will change to blinking GREEN and BLUE LEDs 2. Enter the default Admin PIN ‘11223344’ and press the ‘UNLOCK’ button GREEN and BLUE LEDs blink rapidly together for a few seconds then to a solid GREEN and finally a solid BLUE LED indictaing the diskAshur2 is in ‘Admin Mode’ 3. In Admin mode (solid BLUE LED), press and hold down ‘UNLOCK + 2’ buttons Solid BLUE LED will change to blinking GREEN and solid BLUE LEDs 4. Enter your NEW Admin PIN and press ‘UNLOCK’ button Blinking GREEN and solid BLUE LEDs will switch to a single GREEN LED blink and then back to blinking GREEN and solid BLUE LEDs 5. Re-enter your NEW Admin PIN and press ‘UNLOCK’ button Blinking GREEN and solid BLUE LEDs change to a rapidly blinking BLUE LED and finally to a solid BLUE LED indicating the Admin PIN has been successfully changed 6. To exit Admin Mode press the ‘LOCK’ button Solid RED LED indicates the drive is locked and in the standby state In addition to the Admin PIN, the diskAshur2 can be configured with an independent User PIN. To create a new User PIN follow the steps below. 1. In Standby State (solid RED LED), press and hold down both the ‘UNLOCK and number ’1’ buttons Solid RED LED will change to blinking GREEN and BLUE LEDs 2. Enter your Admin PIN (default ‘11223344’) and press the ‘UNLOCK’ button GREEN and BLUE LEDs blink rapidly together for a few seconds then to a solid GREEN and finally a solid BLUE LED indictaing the diskAshur2 is in ‘Admin Mode’ 3. In Admin mode (solid BLUE LED), press and hold down ‘UNLOCK + 3’ buttons Solid BLUE LED will change to blinking GREEN and solid BLUE LEDs 4. Enter your NEW User PIN and press ‘UNLOCK’ button Blinking GREEN and solid BLUE LEDs will switch to a single GREEN LED blink and then back to blinking GREEN and solid BLUE LEDs 5. Re-enter your NEW User PIN and press ‘UNLOCK’ button GREEN LED rapidly blinks for a few seconds then changes to a solid BLUE LED indicating the User PIN has been successfully created 6. To exit Admin Mode press the ‘LOCK’ button Solid RED LED indicates the drive is locked and in the standby state