iPower SUA2000iD Owner's Manual

Packing Dimension: L x W x H 19.7×11.4×18.3inch 21.7×13.0×20.0inch SAE 10W-30 48.4 lbs Model SUA2000iD 1600W-GAS / 1500W-LPG 2000W-GAS / 1800W-LPG

4. Low Oil Alarm Overload Alarm Output Indicator 5. FUEL SOURCE switch 9. AC 120V Receptacle (30A) 10. AC 120V Receptacle (20A) 8. CHOKE 7. Grounding Nut Ground generator to reduce risk of electric shock 6 7 8 1 2 3 4 2. LOW IDLE Turn ON to increase fuel economy and runtime when the load is below 75% load 6. Parallel Operation Outlets Connect two AIPOWER inverter generators through a parallel connection kit for a higher output 10 9 5

Sockets Connect the Parallel Cables first, then start the greater wattage unit first if different from the other. The Fuel Selector Switch controls the desired fuel source. When switch is turned left, gasoline is selected. When switch is truned right, LPG is selected and hose inlet is exposed for hook up. Fuel Selector Switch

1. Turn the FUEL SOURCE switch (Fig. 7) to the “GAS” position. 3. Turn the MAIN switch (Fig. 8) to the “ON” position. 6. Place one hand on the generator to hold it in place, and pull on the recoil starter handle slowly until a slight resistance is felt (Fig. 11). Then pull quickly to start the engine. Return cord gently into the machine. Never allow the cord to snap back. NOTE: If you have repeated failed attempts to start the engine, please consult the troubleshooting guide. 7. Allow the generator to run for several minutes before attempting to connect any electrical devices. This allows the generator to stabilize its speed and temperature. 4. While holding the fuel tank cap so that it will not move turn the air vent knob to “ON”(Fig. 9) Fig. 11 Fig. 9 Fig. 8 Fig. 10 Fig. 7 (NOTE: Skip this if starting the generator with a warm engine.) 5. Pull the CHOKE LEVER (Fig. 10) out to the “START” position.

4. Turn the LOW IDLE switch (Fig. 8) to “OFF”. 1. Turn the FUEL SOURCE switch (Fig. 11) to the “LPG” position. 8. Place one hand on the generator to hold it in place, and pull on the recoil starter handle slowly until a slight resistance is felt (Fig. 11). Then pull quickly to start the engine. Return cord gently into the machine. Never allow the cord to snap back. 2. Connect the LPG gas hose to the propane fuel source (Fig. 12). 3. Connect the small end of the LPG gas hose to the LPG regulator on the generator and then snug with a wrench to prevent leakage (Fig. 13). 6. Rotate the LPG valve to open the LPG (Fig. 14). Fig. 12 Fig. 11 Fig. 13 Fig. 14 5. Turn the MAIN switch (Fig. 8 ) to the “ON” position. 7.With the choke at "RUN" (Fig. 10), press and hold the pressure-reducing valve button to store air for 3.5 seconds. (NOTE: Skip this if starting the generator with a warm engine.)

generators together. By using the parallel connection wires provided. G SUA2000iD Attention: Be sure generators are powered off and without load when connecting the parallel wires. s

Make sure to connect the correct parallel wire into the correct socket. Connect the parallel wires when generator is off. Parallel wires are not necessary when only one generator is being used. A-IPOWER A-IPOWER ③ ⑤ Refer to the "Starting" section of the manual cause damage.

the Positive (Red) cable. Do not reverse these cables and take care as to not let the cables touch eachother or other items.

the engine oil.Then tighten the dipstick. 6. 7. 8.

Register your product by mailing this form to [email protected] or register online at www.a-ipower.com. Registering your product is important, it provides protection: 1) You have record of product purchased. 2) Customer Service can Better serve you for Warranty related issues. 3) We can contact you in the unlikely event should notification is necessary. 4) Alway keep copy of your orginal receipt.