ICPDAS TPD-433-M2 Quick Start Manual
Read Online
Read the ICPDAS TPD-433-M2 Quick Start Manual online using the built-in PDF viewer.
Text of the manual
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 1 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
TPD-433-M2
Quick Start Version 1.0
1 Shipping package
Thanks for buying ICPDAS TPD-433-M2 device. This shipping package contains the following items:
TPD-433-M2 x1 Quick Start x1 Back Piece x1 Round Head Screws x2
2 Appearance
Front View Rear View
Serial Port
USB
Rotary Switch
Ethernet
4.3” TFT LCD with Touch Panel
LED
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 2 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
3 Pin Assignment
On the back of the TouchPAD:
The pin assignments:
Pin
Description
F.G.
Frame Ground. F.G. is connected to the inside EMI or ESD suppression circuits.
Make sure that F.G. is connected to the Earth
VDC
DC input Voltage (range: +12 V ~ +48 V)
GND
Connected to the power supply’s ground pin
D1+
The positive data line of the RS-485 network
D1-
The negative data line of the RS-485 network
GND
Ground pin
TxD2
The pin of transmitted data of the RS-232
RxD2
The pin of received data of the RS-232
The definition of the rotary switch:
No
Mode
Description
0
Run &
Update
(Ethernet)
This is a special run mode which is used in the development
stage. The TouchPAD device can be updated by a PC from the
remote side through Ethernet.
1
Ethernet
Force
Update
While the application run on the TouchPAD device seriously
crashes, use this mode to update a new application to the
TouchPAD device through Ethernet.
2
Run Only
Run the program.
9
USB Force
Update
Update a new application to the TouchPAD device through
USB.
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 3 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
4 First Use of the TPD-433-M2
1.
Connect wires as the figure. External Power can be removed
if you have a PoE Switch providing power through an Ethernet
cable to the TouchPAD. And set the rotary switch to zero (At this
point, the power is not yet supplied).
2. Supply power to the TPD-433-M2, wait for several
seconds and then you can see the default program run
on it.
3. Try to touch on the icons on the screen of the
TPD-433-M2 and you can find that TPD-433-M2
switches to another page.
5 Creating First Project
To create your first project of the TPD-433-M2, install the free development tool, HMIWorks and
then refer to <>, which can be found on the FTP:
http://ftp.icpdas.com/pub/cd/touchpad/document/english/programming_guide/
Use a flat-head screwdriver to
set rotary switch
PoE Switch
External Power
GND
VDC (+12~+48V)
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 4 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
6 Related Information
TPD-433-M2 Product Page:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/tpd-433-mx.html
Documents, such as the user manuals, the API references, etc.:
ftp://ftp.icpdas.com/pub/cd/touchpad/document/english/
Free Development Software, HMIWorks v2.10.24 or above:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email at:
[email protected], [email protected]
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 5 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
TPD-433-M2
快速入門指南 版本1.0
1 檢查配件
感謝您購買泓格的TPD-433-M2 產品。產品包裝內應包含下列配件:
TPD-433-M2 x1 快速入門指南x1 固定座x1 圓頭螺絲x2
2 外觀
前配置圖 後配置圖
LED
Ethernet
4.3 吋觸控液晶螢幕
序列埠
USB
旋轉開關
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 6 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
3 腳位定義
在TouchPAD 的背面可見到如下圖樣:
腳位定義:
Pin
說明
F.G.
機架接地，F.G. (連接到內部的EMI 或ESD 保護電路)，請接到大地。
VDC
直流電壓輸入 (範圍：+12 V ~ +48 V)
GND
連到電源的接地端
D1+
RS-485 網路的正訊號線
D1-
RS-485 網路的負訊號線
GND
接地端
TxD2
RS-232 的傳送資料腳位
RxD2
RS-232 的接收資料腳位
旋轉開關 (Rotary Switch) 的配置模式定義:
項次 模式
說明
0
Run & Update
(Ethernet)
執行/更新程式，用於程式開發階段 (能執行程
式，也能進行更新)。通過乙太網路可進行遠端更
新程式。
1
Ethernet Force
Update
強制更新，當程式嚴重毀損時可用此模式透過
Ethernet 更新。
2
Run Only
執行程式 (只能執行程式，不能進行更新)。
9
USB Force Update 透過USB 更新程式。
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 7 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
4 第一次使用 TPD-433-M2
1. 如左圖所示，將電源和接地線連接完成。若您使用 PoE
Switch 透過網路線給 TouchPAD 供電，則可省略外部供電器。
然後將旋轉開關(Rotary Switch)轉到0(此時尚未供電)。
2. 開始供電給TPD-433-M2，等待約數秒的開機時間，
接著可以看到TPD-433-M2 執行出貨預附的程式如圖
所示。
3. 試著按一下TPD-433-M2 螢幕上面的圖示，
TPD-433-M2 會切到其他的頁面。
5 建立第一個軟體專案
在建立TPD-433-M2 的第一個專案之前，請先安裝免費的開發軟體HMIWorks。然後參考<<
TouchPAD_programming_guide.pdf>>這份文件，一步一步地完成。該份文件可以在FTP 上找
到：
http://ftp.icpdas.com/pub/cd/touchpad/document/chinese/programming_guide/
使用一字起子來配
置旋轉開關
外部供電器
GND
VDC (+12~+48V)
乙太網路供電
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 8 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]
6 參考資訊
TPD-433-M2 產品網頁:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/tpd-433-mx_tc.html
相關文件，如使用手冊、API 函數手冊…等:
ftp://ftp.icpdas.com/pub/cd/touchpad/document/english/
免費開發軟體，HMIWorks 版本2.10.24 或以上版本:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
如有任何問題歡迎聯繫我們，我們將會為您提供完善的咨詢服務:
E-mail: [email protected], [email protected]
