FrSky VS600 Instruction Manual

Inner Frame 28*28*4.3 mm (L*W*H) • Weight: 3.7g • Transmission Frequency: 5.8 GHz • Available Channel: 48 • Operating Voltage: DC 7V~28V • Operating Current: 260mA@12V (200mW) • Transmission Power: 1mW(Pit mode) / 25mW/ 200mW/ 600mW Features • Pit Mode supported • Small and portable • Clear LED indication • Adjustable operating band • Optional installation position FrSky Electronic Co., Ltd www.frsky-rc.com Contact us : [email protected] Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected] FrSky Electronic Co., Ltd www.frsky-rc.com Contact us : [email protected] Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected] Introduction Thank you for purchasing FrSky VS600 video transmiter. As a multi-functional unit, it is equipped with switchable operating power and operating band. In order to fully enjoy the benefits of the product, please read the instruction manual carefully and set the device as described below. Instruction Manual for VS600 Mounting Method Overview Transmission Frequency Instruction Manual for VS600 S.PORT V_IN GND VIDEO GND 5V_OUT TOP 28mm 28mm Blue LED RED LED GREEN LED BOT 36mm 36mm 20mm 31mm 1. 30.5*30.5 mm mounting hole diameter: 3.1 mm 2. 20*20 mm mounting hole diameter: 2.5 mm A B C D E F CH1 5865 5733 5705 5740 5658 5362 CH2 5845 5752 5685 5760 5695 5399 CH3 5825 5771 5665 5780 5732 5436 CH4 5805 5790 5645 5800 5769 5473 CH5 5785 5809 5885 5820 5806 5510 CH6 5765 5828 5905 5840 5843 5547 CH7 5745 5847 5925 5860 5880 5584 CH8 5725 5866 5945 5880 5917 5621 CH FR (MHz) LED Indication LED Green: There are 8 green LEDs indicating 8 channels. The number above the LED indicates the corresponding channel. For example, If LED 1 is on, CH1 is operating. LED Red: There are 6 red LEDs indicating 6 different operating frequencies. The letter above the LED indicates the corresponding frequency. For example, If LED A is on, VS600 works under Frequency A. LED Blue: There are 3 blue LEDs indicating 3 different operating powers. Different from LED Green and LED Red, the number of lighting LED indicating different powers. From left to right, if there is only one LED is on, the power is 25mW. 2 indicates 200mW and 3 indicates 600mW. Blue LED RED LED GREEN LED Blue Power LED Indication Green Channel Red Band Note: Please be complied with local laws and regulations when selecting operating power. • Manual configuration • Automatic configuration Manual configuration (through Switch B2 & B1) • Switching Channel: Press B2, channel output will switch from 1 to 8 successively. The switch will start from the preset CH output, not always from CH1. • Switching Operating Frequency: Press B1, operating band will switch from A to F successively. The switch will start from the preset operating frequency, not always from Frequency A. • Switching Operating Power: Long Press B2 (about 2 seconds), operating power will switch between 25mW, 200mW and 600mW successively. The switch will start from the preset operating power, not always from 25mW. • Switchable transmission power Specifications Configuration method

www.frsky-rc.com Contact us : [email protected] Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected] Instruction Manual for VS600 Automatic configuration (through S.Port) 1. Channel, Operating Band and Operating Power could be set through the transmitter. Run the gTrans.lua which is on the SD card and start configuration. The interface is below. 2. Channel, Operating Band and Operating Power could be set through the Upper Computer FreeLink. Connect VS600 to the computer and configure parameters with FreeLink. The interface is below. CH2 B25mW 1 1 GTrans Channel: Band: Power: Param Channel Band Power lever D A new feature introduced with VS600 is Pit Mode. It allows the user to power up their video transmitter during race events without interfering with other users and still have the ability to change VTX settings or do some testing. Operation method: Activate: Power on VS600 while holding B1. 3 Blue LEDs will flash teice and then go out, indicating that VS600 enters into Pit Mode. The operating power is less than 0.01mW and the effective distance of image transmission is about 1m. Deactivate: During Pit Mode, long press B1 and 3 Blue LEDs will flash twice. After that, the Blue LED which indicates the corresponding operating power will be on. VS600 enters into normal working mode. Pit Mode Attention NEVER TURN ON TRANSMITTER WITHOUT INSTALLING A PROPER ANTENNA. The factory setup of operating state may be different. VS600 will remember the preset operating state (channel output, operating frequency and operating power) if it is power on again. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.