CYP DCT-23 Operation Manual

is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document. Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Cypress Technology. © Copyright 2012 by Cypress Technology. All Rights Reserved. Version VR1.0 January 2012 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. • Do not attach the power supply cabling to building surfaces. • Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. • Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. • To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. REVISION HISTORY VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE VR0 10/02/15 Preliminary Release

4. System Requirements����������������������������1 5. Features��������������������������������������������������2 6. Operation Controls and Functions�������3 6.1 Front Panel����������������������������������������3 6.2 Rear Panel�����������������������������������������4 6.3 Remote Control��������������������������������5 6.4 OLED Menu���������������������������������������6 6.5 RS-232 Protocols�������������������������������7 6.6 RS-232 & Telnet Commands������������8 6.7 Telnet Control�����������������������������������9 6.8 Web GUI Control����������������������������11 7. Connection Diagram��������������������������12 8. Specifications��������������������������������������13

digital audio from 3.5Ø line in, R/L RCA, HDMI, optical and coaxial inputs and output synchronously to R/L speaker, HDMI, optical and coaxial outputs with microphone sound added. Suitable for any musical events use, sound addition, and sound amplifying. With audio output sampling rate supports up to 48kHz and I/O data rate supports up to 24-bit, it provides a high standard of quality sound presentation an can amplifier sound up to -80dB. 2. APPLICATIONS •  Public speech •  Show event audio set up •  Home theater •  Educational/Lecture presentation 3. PACKAGE CONTENTS •  1 x Integrated Zone Amplifier •  1 x IR Extender •  1 x Remote Control CR-126 •  1 x 24V/ 3.75A DC Power Adaptor •  1 x Power Cable •  1 x Rack Ears set •  Operational Manual 4. SYSTEM REQUIREMENTS Input audio source equipment such as DVD/Blu-ray players, PC, CD player, MP3 and …etc. with output display TV/monitor and active speakers.

Digital audio Conversion(ADC) •  Supports input sampling rate up to 96kHz, output at 48kHz and HDMI loop out •  Supports video resolution from VGA~WUXGA(RB) or 480i~1080p •  Supports HDMI bypass •  Supports microphone sound mix into output sounds •  Synchronous output sound on both digital and analog •  Supports RS-232, Telnet, WebGUI, IR and on-panel controls •  Sound supports up to -80dB •  Elegant design and easy to install/using

6.1 Front Panel EXIT POWER UPDATE Integrated Zone Amplifier CONTROL PUSH MIC 3 1 2 1 2 3 4 5 6 7 1 MIC: Connect with microphone for input sound signal. 2 UPDATE: Connect with USB flash driver for firmware update only. 3 LCM: Display current input source selection and volume setting. 4 IR Window: Accept IR signal from the remote control included in the package. 5 CONTROL: This button has 2 uses, one for volume control and 2 for menu selections. Turn the wheel to adjust the output sound volume outside the menu or press it to enter into the menu selection. After enter into the menu turn the wheel to rotate from the selection and press it again to enter or confirm. 6 EXIT: Press this button to exit from the menu selection. When outside the menu selection press this button to mute the output sound, the LED will illuminate in red . Press it again to unmute. 7 POWER: Press this button to turn on the device and the LED will illuminate in blue. Press it again to switch to standby mode and the LED will turn red.

CONTROL HDMI OUT HDMI IN 1 HDMI IN 2 RS-232 LINE IN OUT OPT. COAX. IN OPT. COAX. R L OUT R SPEAKER RCA IN DC 24V IR IN OUT IN R L R L + - + - 1 2 4 7 12 9 3 5 6 8 10 11 1 CONTROL: Connecting from PC/NB with RJ-45 cable for telnet control. 2 HDMI OUT: Connect to HD TV/monitor for both audio and video display. 3 IR IN: Connect the IR extender included in the package for receiving the IR signal from the device’s remote control. 4 HDMI IN 1& 2: Connect to DVD/Blu-ray players or any HDMI source equipment for input audio and video signal sending. 5 RS-232: Connecting from PC/NB with D-Sub 9pin cable for RS-232 controls. 6 LINE IN: Connect from audio device with 3.5Ø phone jack for stereo audio signal input. 7 OPT. & COAX. OUT: Connect from active optical speakers & coaxial speakers for digital audio outputs. 8 OPT. & COAX. IN: Connect from source equipment such as Set- top-box or PS3 or any other source with optical and coaxial output for audio signal sending. 9 R/L SPEAKER: Connect from speakers with wired cables for stereo audio output. 10 R/L IN: Connect from audio source equipment with RCA jack for stereo audio input. 11 R/L OUT: Connect L/R output to active speakers with RCA jack for stereo audio output. 12 DC 24V: Plug the 24V DC power supply into the unit and connect the adaptor to an AC outlet.

1 POWER: Press this button to switch on the device or set it to standby mode. 2 MUTE: Press this button to mute all the output sound. 3 VOL.▲▼: Press these buttons to turn the output volume up and down. 4 MENU: Press this button to bring up the OLED MENU then press the ▲&▼ buttons to select and press it again to confirm the selection. 5 EXIT: Press this button to return or exit from the menu selection. 6 INPUT: Press these hot keys to switch the input sources instantly. CR-126 MUTE POWER VOL. MENU EXIT HDMI 1 HDMI 2 OPTICAL COAXIAL LINE LR INPUT 1 3 6 2 4 5

1 st layer 2 ND layer Function Select Audio in HDMI Set Display Set MIC Set line out Set IP Config Reset to Default Audio Select* HDMI1 HDMI2 Optical In Coaxial In Line In RCA (LR) In HDMI Setting* Video HDMI1 HDMI2 Audio HDMI Ext Audio Display Set TimeOut 5s TimeOut 10s TimeOut 15s MIC Setting OFF Normal Phantom LineMode Volume Line Out Setting Fix Level Default

OK *Note: HDMI audio & video are tie together and when audio select HDMI, video will not be able to select differently other than the selected HDMI port. 6.5 RS-232 Protocols DCT-23 ► ◄ Remote Control PIN Assignment PIN Assignment 1 NC 1 NC 2 Tx 2 Rx 3 Rx 3 Tx 4 NC 4 NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC Baud Rate: 115200bps Data bit: 8 bits Parity: None Flow Control: None Stop Bit: 1

Command Description HELP DISPLAY LIST OF COMMANDS H ALIAS FOR HELP ? ALIAS FOR HELP PWR 0/1 POWER CONTROL S:STATUS, 0:OFF / 1:ON SOURCE 0~5 SOURCE IN SELECTION S:STATUS, 0:HDMI 1, 1:HDMI2, 2:OPT, 3:COAX, 4:LINE IN, 5:RCA IN VOL 0~-80 OUTPUT VOLUME SETTING 0~80dB S:SHOWVOL, +:0.5dB, ++:2dB,-:-0.5dB, --:-2dB or 0~-80 dB MUTE 0/1 OUTPUT VOLUME MUTE CONTROL S:STATUS, 0:UN- MUTE, 1:MUTE MICVOL 0~30 MIC VOLUME CONTROL 0~30dB S:SHOWVOL, +:0.5dB, -:-0.5dB, or 0~30 dB MICMODE 0~3 MIC MODE SELECT S:STATUS, 0:OFF, 1:NORMAL, 2:PHANTOM, 3:LINE MODE FADEFAULT FACTORY DEFAULT SETTING REBOOT REBOOT THE UNIT IPCONFIG PRINT THE IP CONFIGURATION TO THE SCREEN RESETIP RESET THE IP CONFIGURATION TO FACTORY DEFAULTS SHOWMAC PRINT THE MAC ADDRESS TO THE SCREEN SHOWTPORT PRINT THE TELNET COMMUNICATION PORT TO THE SCREEN SHOWHPORT PRINT THE HTTP COMMUNICATION PORT TO THE SCREEN SIPADD SET THE IP ADDRESS SNETMASK SET THE NET MASK ADDRESS SGATEWAY SET THE GATEWAY ADDRESS SHTTPPORT SET THE HTTP COMMUNICATION PORT(1~62235) [80]

[23] Note: All the RS-232 command will be not executed unless followed with a carriage return. All commands are case-sensitive. 6.7 Telnet Control Before attempting to use the telnet control, please ensure that both the Intergrated Zone Amplifier (via the 'CONTROL' port) and the PC/Laptop are connected to the active networks. To access the telnet control in Windows 7, click on the 'Start' menu and type "cmd" in the Search field then press enter. Under Windows XP go to the 'Start' menu and click on "Run", type "cmd" with then press enter. Under Mac OS X, go to Go→Applications→Utilities→Terminal See below for reference.

address and hit enter. Note: The IP address of the Intergrated Zone Amplifier can be displayed on the device's LCM monitor by entering into the Menu's IP Config. This will bring us into the device which we wish to control. Type "H" to list the available commands. Type “IPCONFIG” To show all IP configurations. To reset the IP, type “RESETIP”. Note: All the commands will be not executed unless followed by a carriage return. Commands are case-sensitive. If the IP is changed then the IP Address required for Telnet access will also change accordingly.

On a PC/Laptop that is connected to the active network as the Intergrated Zone Amplifier, open a web browser and type device's IP address on the web address entry bar. The browser will display the device's control page.

CONTROL HDMI OUT HDMI IN 1 HDMI IN 2 RS-232 LINE IN OUT OPT. COAX. IN OPT. COAX. R L OUT R SPEAKER RCA IN DC 24V IR IN OUT IN R L R L + - + - 7m 3m 3m 60° m Amplifier HD TV DVD or Blu-ray Player DVD or Blu-ray Player Active Speakers Active Speakers Active Speakers NB SmartPhone

Line in, 1 x R/L RCA, 1 x D-Sub 9pin (RS- 232), 1 x RJ-45 (Control), 1 x IR, 1 x MIC Output port 1 x HDMI, 1 x Optical, 1 x Coaxial, 1 x R/L RCA, 1 x R/L (SPEAKER) Digital Audio Input/Output LPCM 2CH Stereo Input/Output Level 2 Vrms ± 0.2 HDMI Cable I/O Length 15M/12bits 1080p IR Frequency 38kHz ESD Protection Human body model: ±8kV (air-gap discharge) ±4kV (contact discharge) Power Supply 24V/ 3.75A DC (US/EU standards, CE/ FCC/UL certified) Dimensions 215 mm(W) x 172.5 mm(D) x 46 mm(H) Weight 1060 g Chassis Material Aluminum Silkscreen Color Black Operating Temperature Operating from 0°C ~ 40°C Storage Temperature -20˚C ~ 60˚C / -4 ˚F ~ 140 ˚F Relative Humidity 20 ~ 90% RH (non-condensing) Power Consumption 82.5W Power Output 30W/Channel @ 8Ohm (0.1% THD+N)

<0.1% ±1 dBFS >70dB Analog L/R PhoneJack 2.0 Vrms/1kHz HDMI OPTICAL 0dB±1dB <0.01% ±1 dBFS >80dB COAX L/R 2.0 Vrms ±10% <0.1% ±1 dBFS >80dB Amplifier Specification: