CyberData 011528 Installation Quick Reference

© 2021, CyberData Corporation, ALL RIGHTS RESERVED 931826A Quick Reference Installation Method The site where you install the switch may greatly affect its performance. When installing, please take the following into consideration: • Test the PoE network drop before connecting the CyberData device. • Use caution when inserting or modifying connections and install the product in a clean, flat wall surface. • Ensure there are no temperature or humidity concerns in the intended environment. See the Specs tab at https://www.cyberdata.net/products/011528 for the acceptable temperature and humidity operating ranges. • To prevent electrical issues, avoid installing in close contact with other electrical wires, next to in-wall insulation, or exposing the circuit board upon completing the installation. • Never install components in wet locations or during lightning storms. • It is advised to consult a certified electrician for installation. Typical Wall Installation Parts 1 Plug in the network cable and angle in 2 Secure Unit with Faceplate Screws 3 Fold flagnuts down, then insert into wall cutout and tighten screws (1) Low Voltage Bracket (2) Faceplate Screws (2) PCBA Mounting Screws Accessory Kit (1) PCBA (1) Faceplate Dimensions Mount PCBA to Faceplate Contacting CyberData 2.756 [70] 4.567 [116] 0.177 [4.5] 3.900 [99] 3.270 [83] DIMENSIONS ARE IN INCHES [MILLIMETER] Dimensions are in Inches [Millimeters] 2.250 [57.15] 3.875 [98.43] Dimensions are in Inches [Millimeters] Faceplate PCBA Mounting Screw Sales: 831-373-2601 ext. 334 Support: 831-373-2601 ext. 333 Support Website: http://support.cyberdata.net/ RMA Department: 831-373-2601 ext. 136 RMA Email: [email protected] RMA Status: http://support.cyberdata.net/ Warranty Information: http://support.cyberdata.net/ Corporate Headquarters CyberData Corporation 3 Justin Court Monterey, CA 93940, USA Phone: 831-373-2601 Fax: 831-373-4193 http://www.cyberdata.net/ The IP Endpoint Company Installation Quick Reference In-Wall 2-Port Gigabit PoE Switch 011528 Wall Cutout

931826A Quick Reference Quick Reference 931826A © 2021, CyberData Corporation, ALL RIGHTS RESERVED The Standard RJ-45 Introduction Regarding cable-making methods, a cable that does not meet the standards of the sequence data will make the data transmission speed slow, unstable, and even be blocked. Table 1 represents the standard RJ-45 jack and the connector (Figure 1) and pin definition: Figure 1. Standard RJ-45 Jack / Connector The Standard Cable, RJ-45 Pin Assignment The following figures show a straight cable and a crossover cable connection. Use a straight cable connection to connect switch/ Hub or other devices: Straight cable for the switch (uplink MDI-II port) to switch/Hub or other devices connection. Crossover cable for switch (MDI-X port) to switch/hub or other network devices (MDI-X port) connection. Table 1. RJ-45 Connector Pin Definitions Pin Number Signal 1 _TX1 +(PoE Power+) 2 _TX1 - (PoE Power+) 3 _RX1 + (PoE Power-) 4 _TX2 + 5 _TX2 -- 6 _RX1 - (PoE Power-) 7 _RX2 + 8 _RX2 - 1 2 3 4 5 6 7 8 Powering on the In-Wall 2-Port Gigabit PoE Switch Your existing central POE Switch powers the CyberData switch. No additional power supply is required. Plug your cable from your main PoE switch into the ethernet port of the CyberData switch, which will power on for use. How the Input Power is Distributed Typical Installation LED Status Description PD (Orange) ON Switch has a connection from the PD port to the PSE device. Power has been successfully applied. OFF Connection to the PSE device is not present. No power has been applied to the switch. PSE (Orange) ON PD device such as IP phone is connected to the port and drawing power. OFF PD device is not connected or no power is being drawn from the switch. Link/Act (Green) ON A valid link is established. Blink Traffic is present on port. OFF No link has been established.