AsReader ASR-020D Operation & User’s Manual

ASR-020D ASR-010D User Manual Inside the Box Parts of AsReader Safety Instructions 　Thank you for using the AsReader. This manual contains important safety instructions for using the AsReader. Please read the manual carefully and keep it as long as you have the device. ※We may refer to the AsReader as “the device” or “this device” in some sections of this manual. In order to prevent damage or malfunctions, Do NOT try to disassemble, modify, or repair the device by yourself. Stop using the device if you found any smoke or abnormal smells emanating from the device. Do not drop, throw, or stike the device. Do not expose this device to fire, high temperature or water. If you notice any damage to the device, stop using it. Battery changing by the end user is not allowed. There is risk of fire, explosion, or burns. Do not try to recharge the battery when the device is dripping wet or near any object filled with liquid. the magnetic connector is not water proof. Damage may occur if short-circuits or electrical shorts occur to the parts. Do not touch these parts with wet hands. Do not try to use this device in wet environments. Do not try to use a broken charging cable or magnetic connector due to risks of electrical shorts. Do not put this device on high temperature surfaces, such as car hoods or dashboards. Don’t look at the LED light on the bar code scanner due the risk of eye damage. The device’s magnetic connector has a magnet which may cause some risk of deletion of data on any magnetic cards. Therefore, please keep any magnetic cards, or related items, at least 100mm (4 inches) away from the device. 　Please read the following instructions carefully before use Before Using 　There is a protect seal on the window of the barcode scanner. Please remove it before using AsReader. The following items are contained in the box. Please first make sure you have all of these items. In case that any items are missing, please contact the company from whom you purchased the device. ●AsReader ●Magnetic Cable ●Headset extension cable ●User Manual (this) ……………1 pc ……………1 pc ……………1 pc ……………1 pc Warning Only use the magnetic cable and magnetic connector included in the package. Standard iPhone/iPod touch recharger (5V1A) is strongly recommended for use with the magnetic cable. Using different chargers may result in failed charges. Please refer to local regulations when you recycle this device. Please contact your local purchasing source immediately if any abnormal incidents occur. Although this device is designed to be drip-proof, long expose to rains may damage the installed iPhone/iPod touch. Please try to avoid dripping on the device. Wipe any drips from the device immediately. Do not try to recharge the device or disconnect the iPhone/iPod touch when the device is wet; there are risks of liquid leaking into the device through the connector. Do not use this device in any circumstance which may cause significant impact to the device due to dropping or misuse by the user. Caution

battery. With iPhone/iPod touch, push the trigger button on AsReader for 5 seconds, the LED light will light as the current battery status. LED Indicator 　The LED indicates the status of the device. Red：Recharging　 Blue：Reading ※When reading during recharging, the LED will be displayed in purple. Scanning 　The device will start scanning by pressing the trigger button on either side. Scanning can also be triggered from software depending on the app you use. Please contact the vendor of the app. Battery changing 　Battery exchanges are available at user’s cost. Battery exchanges by end-users are not allowed. Failure 　If you experience any failure of this device, please contact your purchasing source. Supported Environment Maintenance 　Please keep the device clean. Using solvents of high-volatility may cause color changes and performance problems. 　iPhone / iPod touch failures may cause errors on this device; please try to restart your iPhone / iPod touch device. Please also make sure the device is properly connected with iPhone / iPod device through the lightning connector. Charging 　Recharging time is approximately 2 hours for this device. 　Please make sure the device is fully recharged before using the device. When using this device simultaneously with the installed iPhone/iPod touch, please keep in mind that the battery of this device is designed to last longer than that of the iPhone/iPod touch. 　The LED will be turned off when the device is fully recharged. The connector will continue to recharge the installed iOS devices until they are all fully recharged even though the LED indicator is off. Can not connect to iPhone/iPod touch 　Make sure the device battery is charged. Otherwise, please make sure that the device has been set up with bar code parameters. Can not scan AsReader 　Rev.2 201903 Notes on operating environment and on how to care for your device 　Always make sure the device is clean when you use it. Depending on the circumstances in which you use the device, oil or chemicals may adhere to it, which can lead to damage of the casing of the device. ・Chemicals 　Cosmetic products, detergents, pesticides, paint thinner, benzine, etc. ・Oil 　Hand creams, animal oils such as beef tallow, etc. If the device is dirty, please clean it by wiping it with a soft, dry cloth. If you use volatile solvents or other chemicals to clean the device, this may lead to discoloration and/or other deterioration. 　You can find support information about this product on our website. Please refer to the website for details. ●Warranty is 1year from date of purchase. ●Make sure to retain documents or receipts that can prove the date of purchase. ●Design and specifications are subjected to change without any notification. ●iPhone/iPod touch is the trademark of Apple Inc. ＜AsReader Product website＞ https://www.AsReader.com AsReader Inc. 6663 SW Beaverton Hillsdale Hwy., PMB 314 Portland, OR 97225-1403 U.S.A. Tel: +1 (503) 770 2777 https://www.AsReader.com