Explore Scientific Easy Time Clock US100C-ID-WiFi Setup Instructions

Proximity Card Reader Setup Instructions Customer Service 405-314-2436 _________________________________________________________________________________ Page 1 of 9 Easy Time Clock Customer Service 405-314-2436 ©2003 - 2012 Easy Time Clock, All Rights Reserved Welcome to the Easy Time Clock US100C-ID-WiFi Fingerprint and Proximity Card reader quick easy setup instructions. Before using, please read this manual carefully to avoid unnecessary damages! Please don’t place the product in the place with strong light, because the strong light may significantly affect the fingerprint scanning, and thus cause the fingerprint verification fail. Don’t place the terminal in an area where the temperature exceeds 104F or 040C. US100C proper working temperature range is 104F or 040C. If the temperature of the machine gets too hot, the device will be affected easily, such as, the slower reaction speed and the reduced passing rate. If mounted outdoors, place the unit in a shaded well ventilated area and/or use cooling equipment to keep the area temperature controlled. There are seven easy steps to configure your terminal. 15 minutes approx time. STEP 1 Setup US100C-ID-WiFi– Install unit on wall according to instructions 1) Power on the system will boot up and the reader will then search for your network. a. Starting Network will display a plane black box. b. Searching for server will display a green letter “I” in the black box. I c. Connected to server will display a green box in the upper right corner. Look for the Easy Time Clock logo display to easily see the black box. If your wireless configuration was preset, you will see the system to try to connect to your access point. If your reader did not have your wireless configuration preset, go to the next step to enter in your wireless configuration. 2) Press M/OK to go to your menu options 3) Move to 2. Comm. and press M/OK (Press the */> key to move right)

Proximity Card Reader Setup Instructions Customer Service 405-314-2436 _________________________________________________________________________________ Page 2 of 9 Easy Time Clock Customer Service 405-314-2436 ©2003 - 2012 Easy Time Clock, All Rights Reserved 4) Arrow down ▼to Wireless LAN and press M/OK 5) Arrow down ▼to your SSID and press M/OK 6) Arrow down ▼to Password and press M/OK 7) Enter the password with T9 input (see T9 Input note below on page 7) 8) Arrow down▼ and press M/OK 9) Arrow down ▼to OK (M/<-) and press M/OK 10) Reboot as prompted Note: If the fingerprint reader takes a long time to boot up, the WiFi configuration is wrong and it is searching for the Access Point. When it works, you will have a green capital letter I in a green box near the top right hand corner of the screen. If you want a static IP address, you will see the option on the same WiFi Setup page.

Proximity Card Reader Setup Instructions Customer Service 405-314-2436 _________________________________________________________________________________ Page 3 of 9 Easy Time Clock Customer Service 405-314-2436 ©2003 - 2012 Easy Time Clock, All Rights Reserved STEP 2 Assign ID Card Number and Download Your Employee Names From your Easy Time Clock account 1) Login as Admin into your Easy Time Clock account 2) Go to Main Menu | Employee Setup | Fingerprint and ID Card Clock Download page. NOTE: If the Employee # is missing, go to the Employee Maintenance | Payroll Setup page and enter the Employee’s identification number in the column and save changes. The download looks for an Employee ID number to identify the employee’s name. You can enter the employees ID number listed in your payroll software or if you do not have a payroll software that has assigned employee id numbers, just number create your own ID numbering system, like 1,2,3 etc. Maximum number of digits is 5. (All numbers not starting with zero.) 4) Type in the assigned Card ID Number listed on the proximity card. 5) Check the box to select the employees to download to the US100C and click the Download button (Request Processed) **To see the downloaded employee list in the clock go to M/OK – User Mng – M/OK - */> - Manage – M/OK

Customer Service 405-314-2436 Search Employee List by ID number a. On the Manage screen with the long list of employees, press OK. b. You will see a list of functions with c. Select Search User and p the search screen. d. Enter the employee number employee will be highlighted. STEP 3 Capture the fingerprints At the US100C, go into User Management ☺ Notice: 1) means this employee is the administrator. 2) means password has been enrolled. Highlight each name, Press M/OK, M/OK (Press to move up and down. 3) The Enroll FP (Fingerprint) button will be 4) Enroll the fingerprint reader screen of the terminal three times to capture the best print. 1.1 How to place a finger Fingerprint enrollment and identification shall be taken after installing US100 2.1 Recommended fingers It is recommended to use the index finger, middle finger or ring finger 3.1 Place a finger Biometric Fingerprint Reader and Proximity Card Reader Setup Instructions Customer Service 405-314 _________________________________________________________________________________ ©2003 - 2012 Easy T by ID number screen with the long list of employees, You will see a list of functions with Search User on top. Select Search User and press OK again and you will see employee number and press OK and the highlighted. User Management and Manage means this employee is the administrator. means password has been enrolled. M/OK, press to select , to move up and down.) (Fingerprint) button will be highlighted, press the fingerprint – Press the index finger of the right hand in the green LED reader screen of the terminal three times to capture the best print. **Print Reading Poor: If you do not get a print reading, there will be an error with the RED X and the terminal voice will “Please Try Again”. **Print Reading Good: When the reader is get a good print reading, you will display a “Enroll Success: OK” print. Do you want to save prompt pops M/OK, and ESC when finished. Select the list. Fingerprint enrollment and identification shall be taken after installing US100 It is recommended to use the index finger, middle finger or ring finger; avoid the Biometric Fingerprint Reader and Proximity Card Reader Setup Instructions 314-2436 _________________________________________________________________________________ Page 4 of 9 Time Clock, All Rights Reserved 1) 2) press M/OK Press the index finger of the right hand in the green LED : If you do not get a good message al voice will say When the reader is able to get a good print reading, you will display a message 5) Save . Do you want to save prompt pops up, press the next employee from Fingerprint enrollment and identification shall be taken after installing US100 well. the thumb and little finger .

Proximity Card Reader Setup Instructions Customer Service 405-314-2436 _________________________________________________________________________________ Page 5 of 9 Easy Time Clock Customer Service 405-314-2436 ©2003 - 2012 Easy Time Clock, All Rights Reserved Notice: Please adopt the correct way to place a finger when enrolling and identifying, to avoid the lower identification caused by unnecessary operations. STEP 4 Test the Card 1) Test clocking in with the card by placing the card in front of the sensor area. Employee can now clock in and out using just the fingerprint without a password. When print is accepted the system will show the name of the employee and the clock in or out time displayed. 2) Look at the Detailed Report in Easy Time Clock to see the clock in. Now your employees are ready to use the US100C-ID to clock in and out. Next Setup the Administrator to lock out the menus.

Customer Service 405-314-2436 STEP 5 – IMPORTANT!! Setup Fingerprint/ID Reader Administrator Limit the Manage functions (the M/OK can enter the Manage area. To limit this, set one or more people to be Administrators. 1) Press M/OK to enter the Main Menus 2) Press M/OK to enter 1.UserMng 3) Arrow to the right to Manager 4) Arrow down to select the ID.No added to help with this) and press 5) Arrow down to Edit and press 6) Arrow down to Purview and Arrow to the right 7) Arrow down to OK and Press 8) You will see a lock next to the user to show that they are now an ☺ Important: 1) means this employee is the administrator. 2) means password has been enrolled Note: If the screen says "Admin Affirm 1 finger printer reader has been set to require an administrator to access the management features. The number shown with Admin Affirm is the number of users with administrator access. To enter the management features simply use the administrator’s finger print. If the administrator is no longer available or was never set, contact us for help resetting the administrator requirement STEP 6 --OPTIONAL -- Enroll Password 1) At the US100C, go into User Management 2) Highlight each name, Press M/OK, press M/OK (Press to move up and down. 3) Press select Enroll PW (Password) button, press 4) Input Password: Type in 8 digit password Biometric Fingerprint Reader and Proximity Card Reader Setup Instructions Customer Service 405-314 _________________________________________________________________________________ ©2003 - 2012 Easy T Setup Fingerprint/ID Reader Administrator: M/OK button) to require a fingerprint or password. By default, anyone Manage area. To limit this, set one or more people to be Administrators. to enter the Main Menus 1.UserMng Manager and press OK ID.No to set as administrator (during the download, the ID.NO of 9999 was added to help with this) and press M/OK to open the next menu and press M/OK and Arrow to the right to change from User to Admin and Press M/OK to Save next to the user to show that they are now an Admin this employee is the administrator. means password has been enrolled Admin Affirm 1" and shows a picture of a padlock , the finger printer reader has been set to require an administrator to access the The number shown with Admin Affirm is the number of users with administrator access. To enter the management features simply use the If the administrator is no longer available or was never set, the administrator requirement. User Management and Manage M/OK, press to select , to move up and down.) select Enroll PW (Password) button, press M/OK Input Password: Type in 8 digit password. (All numbers not starting with zero.) Biometric Fingerprint Reader and Proximity Card Reader Setup Instructions 314-2436 _________________________________________________________________________________ Page 6 of 9 Time Clock, All Rights Reserved button) to require a fingerprint or password. By default, anyone Manage area. To limit this, set one or more people to be Administrators. to set as administrator (during the download, the ID.NO of 9999 was Admin , the finger printer reader has been set to require an administrator to access the The number shown with Admin Affirm is the number of users with administrator access. To enter the management features simply use the If the administrator is no longer available or was never set,

Proximity Card Reader Setup Instructions Customer Service 405-314-2436 _________________________________________________________________________________ Page 7 of 9 Easy Time Clock Customer Service 405-314-2436 ©2003 - 2012 Easy Time Clock, All Rights Reserved 5) Press select to move cursor to the next PW field and type the password again to “Affirm” password, press M/OK to save, 6) Press Esc popup to save PW, select M/OK for Yes. 7) Go to back to the employee list. 8) Press to move the cursor or selection. Follow the same instructions for all of the employees. Change Password: 1) At the US100C, go into User Management and Manage 2) Highlight each name, Press M/OK, press to select , press M/OK (Press to move up and down.) 3) Press select Change PWD (Password) button, press M/OK 4) Input Password: Type in 8 digit password. (All numbers not starting with zero.) 5) Press select to move cursor to the next PW field and type the password again to “Affirm” password, press M/OK to save, 6) Press Esc popup to save PW, select M/OK for Yes. 7) Go to back to the employee list. 8) Press to move the cursor or selection. Follow the same instructions for all of the employees. T9 Input T9 means “Text on 9 keys.” It is commonly used on cell phones. The US100C uses a combination of keys to enter uppercase, lowercase, and symbols. Here is an overview: 1) Arrow to get to the name text field, press the right arrow */ and you will see a gray bar at the bottom of the screen with the word [English] . 2) To get a letter, press the number key with the letter you want on it and you will see a second line with numbers followed by upper and lower case letters. Press the number to the left of the letter you want. 3) To get symbols, press the right arrow a second time and you will see the second row with numbers followed by symbols. To see more symbols, arrow down. You can select a symbol by pressing the number key or you can go back to Letters by pressing the right arrow again.

Proximity Card Reader Setup Instructions Customer Service 405-314-2436 _________________________________________________________________________________ Page 8 of 9 Easy Time Clock Customer Service 405-314-2436 ©2003 - 2012 Easy Time Clock, All Rights Reserved 4) To remove letters, press the / for backspace to remove the letters. 5) Back to number, press ESC to get back to the numbers. Here are the setups to enter a word that starts with a capital A: 1) Press the right arrow */ and you will see a gray bar with the word [English] on the bottom of the screen. 2) Press the number 2 and you will see a second line with numbers followed by upper and lower case letters A through C. � 3) Press the number 3 to get the uppercase A.

Proximity Card Reader Setup Instructions Customer Service 405-314-2436 _________________________________________________________________________________ Page 9 of 9 Easy Time Clock Customer Service 405-314-2436 ©2003 - 2012 Easy Time Clock, All Rights Reserved Cleaning Guidelines From time to time, the surface of optical sensor lens, the keypad and LCD display screen will need to be cleaned to keep your reader in top performance. The optical sensor lens in the unit is delicate and requires special cleaning instructions so to not scratch or damage the lens. Please follow the cleaning guidelines to protect your unit from getting damaged. LCD Display Screen Optical Sensor Lens Keypad Cleaning the Keypad and LCD Display Screen Turn off the unit before cleaning. To clean the keypad and LCD display screen, moisten a soft non-scratch cloth with water or some other mild “all purpose” cleaning spray to clean, like multipurpose spray and wipe or 409 cleaner. It is recommended to dilute the cleaning solution with water. Do not spray or apply water directly on the reader. Test a small section of the keypad to make sure the cleaner will not remove the lettering from the keypad. Lightly wipe the keypad and LCD screen with a damp cloth and air dry. Be sure the keypad and LCD screen is dry before turning on the reader. DO NOT put the reader under running water or immerse in water when cleaning. Cleaning the Optical Sensor Lens Avoid scratching the lens by following the instructions below. Turn off the unit before cleaning the optical lens. 1. If dusty or gritty, first blow air on surface of the lens to clear off any loose particles. 2. It is recommended to first apply any scotch or adhesive tape to clean the surface of lens. Warning: don’t use water and the other cleaning agents for cleaning, which may damage the lens. 3. Use an optical lens cleaning product that is available at most office supply stores and computer supply stores. Use an optical lens cloth or wipes to gently wipe the lens to clean and air dry. Be careful not to scratch the lens when wiping the lens. If you see lint on the lens, lightly blow air on the lens after the sensor is dry. Do Not Use Cotton or Alcohol Wipes.