Code CR3 Quick Start Manual

are connected to the CR3 with a 8-pin DIN connector. Please determine the best connector for use with your host computer. Install a Cable Directly to the CR3 Line up the 8-pin DIN connector into the back end of the unit. The arrows on the connector should be facing down (Figure 1). When the two items are aligned, fi rmly push the cable into the reader. Install a Cable to a Handle If you purchased a cabled handle for use with the CR3, the 8-pin DIN connector is at the bottom of the handle (Figure 3). Line up the cable’s 8-pin DIN connector with the handle’s connector and fi rmly push the cable into the handle. The cable has a locking mechanism that will fi rmly hold the cable in place. To detach the cable from the reader, pinch the plastic on the 8-pin DIN and pull back to disengage the connector. Reader & H2, BH1/BH2 Handle Assembly The CR3 utilizes the battery compartment to ‘snap’ the reader to the H2, BH1 and BH2 handles. For the H2 (only), push the 8-pin DIN connector at the end of the reader into the fl exible connector at the end of the handle. For all three handles, snap the reader onto the handle (Figure 5) matching the battery compartment of the reader to the battery connec- tors, visible inside the handle (Figure 6). Newer readers (MFG # 012_05- see Figure 7) can be secured further with threaded screws on the under side of the handle (Figure 8). This CR3 features a Bluetooth® wireless radio. The radio allows for point to point wireless communication with other Bluetooth devices that support serial port protocol (SPP). The following guide will give you general instructions on connecting your CR3 to a desktop or laptop computer with a Bluetooth radio. Connecting With A QuickConnect Code The easiest way to connect to a Bluetooth device is to visit the Code website and create a QuickConnect Code that is specifi c to your device (Figure 1). This code will link your CR3 directly to the desired Bluetooth device. To create a QuickConnect Code, you will need to know the Bluetooth address (often referred to as the BD_ADDR) of that device. You can usually fi nd the 12-character Bluetooth address somewhere on the device near the device’s serial number (see Figure 2). Code Reader 3.0 - Wireless 4 C002525_03_CR3 Quickstart_Wireless CR3 Wireless Setup Figure 1 Figure 2 Quickstart Guide C002525_03_CR3 Quickstart_Wireless 1 Sample CR3 (Batch Mode) Cable & Handle Installation Figure 3 Figure 4 Figure 1 Figure 2 For additional security, if using the H2 cabled handle, there is an optional cable attachment clip that can secure the cable to the handle with two threaded screws (Figure 4). Reader & H1 Handle Assembly Slide the CR3 into the handle, aligning the 8-pin DIN connector to the stationary connector pin on the handle (Figure 9). Push reader and handle together fi rmly until you feel the reader ‘click’ in place. The cable has a locking mecha- nism that will fi rmly hold the cable in place (Figure 2). To detach the cable, pinch the plastic on the 8-pin DIN and pull back to disengage the connector. Figure 5 Figure 6 Figure 7 Figure 8 Figure 9

All Code Readers come preloaded with Dynamic Optimization Technology (DOT), a revolutionary, adaptive read technology. DOT automatically improves decode performance by con- tinually processing resolution, illumination, and image fi eld settings for the fastest possible symbol identifi cation. You may further optimize DOT technology by scanning predefi ned environment parameters from the user manual. By setting simple parameters such as symbol size and type, the reader will produce instanteous decodes. For more information on DOT, and to begin confi guring your reader for your environment, please consult the CR3 User Manual at: http://www.codecorp.com/support/manuals.htm DOT constantly evaluates decode performance and adapts, offering instant decoding on any type of symbol. CR3 Wireless Setup Reset to RF Factory Defaults QuickConnect Save Settings Radio Range and Transferring Data The CR3 radio is a Class 1 device. If connected to another Class 1 device the unit has roughly a 300 foot line of sight operating range. If connecting to a Class 2 or Class 3 device, the operating range may drop to match the lower range. Once a unit is connected, the application software on the host must be open to receive data. When the CR3 detects the radio is out of range, the CR3 will store data on the reader’s non-volatile memory. For more information about setting up and using the CR3 with a wireless Bluetooth con- fi guration, please visit www.codecorp.com/support and download the latest version of the CR3 User Manual. 2 C002525_03_CR3 Quickstart_Wireless C002525_03_CR3 Quickstart_Wireless 3 If you purchased a CodeXML Bluetooth Modem or a Belkin® Bluetooth adapter from Code or from an authorized distributor, a QuickConnect Code was included. If you bought a Bluetooth adapter separately and wish to create a QuickConnect Code, please visit Code’s web site at: http://www. codecorp.com/support/bdaddr.php. Important Note: While installing the Bluetooth Confi guration Manager software that was included with your Bluetooth adapter, make sure to note the Communications (COM) Port number the software assigned for the adapter (e.g., COM 10). This is the COM Port through which your CR3 will connect. To connect your reader, use the following steps: 1. Power on the CR3 reader. If battery power (no power adapter) is being used, press one of the red buttons for one second to power on the reader. 2. Scan the Reset to RF Factory Defaults code on Page 3 (M684_01). 3. Scan the QuickConnect Code you received or created from Code’s website (see Sample on Page 3). 3. The CR3 will automatically connect to the host computer. By default, the CR3 will beep once after it connects and beep three times in a row if it did not connect. 4. Scan the Save Settings code on Page 3 (M188_02) if you want to save the wireless connection settings to the CR3 so that the CR3 will automatically try to connect wirelessly the next time it is powered on. Scan the QuickConnect code that matches the Bluetooth address of your device. Sample

Our customers turn to us to help them become more productive and profitable. TPI’s expertise guarantees your project will be successful: on time, on budget and meet your ROI requirements. TPI will facilitate your entire wireless and data collection project: � Business analysis � Project justification & ROI � Wireless design, RF site survey and spectrum analysis � WWAN, WLAN design & installation � Custom software � Integration w/legacy systems � Mobile computers � Data collection terminals � Barcode printers, labels and scanners � RFID solutions � Configuration and deployment � Training and installation � Service and upgrades � Remote device management and support TPI can share best practices in data collection from a number of industries including wholesale distribution, manufacturing, healthcare and retail/consumer goods. Our expertise allows you to shorten your learning curve and increase your return on investment. Product specification sheet provided by TPI