Xantech HDMI1X4 Operation & User’s Manual
Text of the manual
- 2 -
INTRODUCTION
Congratulations on your purchase of the HDMI1X4 Splitter. The HDMI1X4 Splitter allows easy
distribution of HDTV devices, using up to four HDTV displays. The line offers solutions for Home
Theater, AV installation, data center, information distribution, conference room presentation, school
and corporate training environments.
The HDMI1X4 Splitter allows one HDTV HDMI device to be distributed easily in to four HDTV HDMI
compatible monitors or projectors. Simply connect your HDTV displays to the DA’s display outputs.
The 1x4 HDMI Splitter can also be placed at the end of a long HDMI cable to regenerate the HDMI
signal.
• Easily distributes HDMI HDTV devices on up to four DVI/HDMI displays with zero signal loss
• Allows simultaneous display
• Maintains 480p, 720p, 1080i, and 1080p resolutions
• Maintains highest HDMI single link video resolution for beautiful HDTV
• Maintains highest HDMI digital audio signal
• HDMI or DVI to HDMI cables are used to connect to the inputs or outputs
• HDCP compliant
• Installs in seconds
The HDMI1X4 consists of:
(1) 1x4 HDMI Splitter
(1) 6 foot HDMI cable (M-M)
(1) 5VDC Power Supply
(1) Users Manual
- 3 -
INSTRUCTIONS
1) Connect the supplied cable from the HDTV HDMI sources into the 1x4 HDMI Splitter input. HDMI
to HDMI cable for HDMI source or HDMI to DVI cable for DVI source.
2) Connect the cables from your displays (monitor or projector) into the HDMI outs of the 1x4 HDMI
Splitter.
3) Plug the 5VDC power supply into the 1x4 HDMI Splitter.
DIP SWITCH GUIDELINES
Inside the HDMI1X4 is a bank of Dip Switches. Below is a table describing their functions. By default,
all switches are set to the Off position.
Dip Switch #
Name
Description
1
Switching Delay
Adds a 3 second delay to switching
2
On Board EDID
Feeds a generic HDMI EDID (720p/1080i) to all inputs
3
IR Code Dip Switch Corresponds to Dip Switch 1 on RMT16-IR
4
IR Code Dip Switch Corresponds to Dip Switch 2 on RMT16-IR
5
Unused
-
6
Unused
-
7
Unused
-
8
Edge Select
+ Edge Pixels
How to open the 1x4 HDMI Splitter:
To access the dip switches, just remove the four screws on the bottom. Slide the top portion off of the
bottom and you should see the dip switches on the board.
- 4 -
SPECIFICATIONS
Video Amplifier Bandwidth
1.65 Gbps
Input Video Signal
1.2 volts p-p
Input DDC Signal
5 volts p-p (TTL)
Single Link Range
1080p / 1920 x 1200
Input Connector Type
HDMI Type A 19 pin female
Output Connector Type
HDMI Type A 19 pin female
Power Consumption
10 Watts (max.)
Power Supply
5V DC
Dimensions
12”W x 1.25”H x 4.125”D
Shipping Weight
5 lbs.
Technical Support
Hours:
7AM-5PM Pacific
Phone:
800.843.5465
press 2 for Tech Support
Fax:
800.492.6832
email:
[email protected]
Mailing Address
Xantech Corporation
13100 Telfair Avenue, 2/F
Sylmar, CA 91342
HDMI1X4 User Manual © 2007 Xantech Corporation
This document is copyright protected. No part of this manual may be copied or reproduced in any
form without prior written consent from Xantech Corporation.
Document Number 08905131A
